Outdoor GreatRoom Company HGI-31 User manual

1
HGI-31 : 1-23-2018 www.outdoorrooms.com
HGI - 31
USER MANUAL

2www.outdoorrooms.com HGI-31 : 1-23-2018
• Important operating and maintenance
instructions included.
• Read, understand, and follow these
instructions for safe installation and operation.
INSTALLER: Leave manual with the appliance.
CONSUMER: Retain this manual for future
reference.
• Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electrical switch;
do not use any phone in the building.
- Leave the building immediately.
- Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
- If you cannot reach your gas
supplier, call the fire department.
• Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
DO NOT DISCARD THIS MANUAL!
WARNING:
WARNING
WARNING
It is imperative the burner be kept clean.
The appliance must be serviced and
maintained to ensure proper operations and
performace. All service should be done by
NFI certied persons.
INSTALLATION AND SERVICE OF THIS
APPLIANCE SHOULD BE PERFORMED BY
AUTHORIZED PERSONNEL.
FOR USE IN WOOD BURNING FIREPLACES
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury, death or property damage.

3
HGI-31 : 1-23-2018 www.outdoorrooms.com
HOT! DO NOT TOUCH!
SEVERE BURNS MAY RESULT!
CLOTHING IGNITION MAY RESULT!
• Glass and other surfaces are hot during
operation and cool-down periods.
• Keep children away.
• Young children should be CAREFULLY
SUPERVISED when they are in the same room
as the appliance. Toddlers, young children, and
others may be susceptible to accidental contact
burns. A physical barrier is recommended
if there are at-risk individuals in the house.
To restrict access to the appliance, install an
adjustable safety gate to keep toddles, young
children, and other at-risk individuals out of the
room and away from hot surfaces.
•Children and adults should be alerted to the
hazards of high surface temperature and should
stay away to avoid burns or clothing ignition.
• CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED ON OR
NEAR THE APPLIANCE.
• PRIMARILY A VENTED APPLIANCE - NOT
CERTIFIED AS A SPACE HEATER!
•Due to high temperatures, the appliance should
be located out of traffic and away from furniture
and draperies.
WARNING WARNING
Improper installation, adjustment, alteration,
service, or maintenance can cause injury
or property damage. DO NOT MODIFY
THIS APPLIANCE. Read the installation and
maintenance instructions thoroughly before
installing or servicing this equipment.

4www.outdoorrooms.com HGI-31 : 1-23-2018
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
CONGRATULATIONS
Congratulations on selecting an Outdoor GreatRoom Company vented gas appliance. The
Gas Appliance you have selected is designed to provide the utmost in safety, reliability, and
eciency.
As the owner of an Outdoor GreatRoom Company gas appliance, you’ll want to read and
carefully follow all of the instructions contained in this owner’s manual. Pay special attention to
all cautions and warnings.
This owner’s manual should be retained for future reference. We suggest you keep it with
other important documents and product manuals.
The information contained in this owner’s manual applies to the HGI-31 only.
Your new HGI-31 will give you years of durable use and trouble-free enjoyment.
WARNING
ALL GAS SUPPLIES MUST BE HARD-PIPED TO THE APPLIANCE.

5
HGI-31 : 1-23-2018 www.outdoorrooms.com
TABLE OF CONTENTS
1. Listing and Code Approvals
a. Appliance Certication
b. Specications
2. Getting Started
a. Design and Installation Considerations
b. Tools and Supplies Required
c. Inspect the Appliance and Components
3. Additional Items Required
a. Packing List
b. Additional Items Required
4. Framing Clearances
5. Gas Hookup and Information
a. Fuel
b. Gas Pressure
c. Gas Connection
d. LP Gas Setup
e. Natural Gas Setup
6. Installation
a. Venting the Appliance
b. Positioning Appliance
c. Testing the Appliance
d. Attaching the Surround
e. Logs and Embers
f. Glass Front
g. Safety Screen
h. Final Verication Tests and Remote Functions
i. Pilot Only Operation
7. Lighting and Operation
8. Troubleshooting
9. Service and Maintenance
10. Reference Materials
a. Service Parts List
b. Dimensional Information
c. Wiring Diagram
d. Checking Test Point Pressure
e. Limited One Year Warranty
6
7
8
8
9
12
19
21
23
24

6www.outdoorrooms.com HGI-31 : 1-23-2018
WHAT’S INCLUDED:
HGI-31 NATURAL GAS
• Multi-speed fan
• Set-up for Natural Gas
• Multi-level ember bed setting
• Glowing embers
• Flexible metal gas line with shut-off
• Owner’s Manual
• Remote Control
1
Listing and Code Approvals
A. APPLIANCE CERTIFICATION B. SPECIFICATIONS
MODEL ORIFICE SIZE
LP - #54 NG - #41
HGI-31
MAX INPUT
BTU
MODEL: HGI-31 Vented Gas Insert
LABORATORY: Underwriters Lab (UL)
TYPE: Sealed combustion gas insert for
use in wood burning replaces.
STANDARD: ANSI Z21.50-2014 Vented
Gas Fireplace / CSA 2.22-2014
HGI-31 has been tested in accordance
with US and Canadian requirements for
vented gas replaces, reference Natonal
Fuel Gas Code ANSI Z223.1/NFPA54 or
the Natural Gas and Propane Instalation
Code CSA B149.1, and operating as
described in these installation and
operating instructions.
The installation must conform with local
codes or, in the absence of local codes, to
ANSI Z21-50 or CSA 2.22-2014.
The appliance, when installed, must be
electrically grounded in accordance with
local codes or, in the absence of local
codes, with the National Electrical Code,
ANSI/NFPA 70, or the Canadian Electrical
Code, Part 1, CSA C22.1.
22,000 BTU/hr - high
16,500 BTU/hr - low
24,400 BTU/hr - high
19,100 BTU/hr - low

7
HGI-31 : 1-23-2018 www.outdoorrooms.com
2
Getting Started
This appliance is a Vented Gas Appliance and
MUST NOT be used for cooking.
Place the HGI-31 system in an existing functional
wood burning replace with a functional ue, this
can be a manufactured replace or site built type.
This location must have a natural gas supply line
or LP gas supply.
When planning an appliance installation, it is
necessary to determine the following information
before installing:
• Where will the appliance be installed? See section 4
• Gas supply piping. See section 5
• Framing and nishing details. See section 4
Before beginning the installation, be sure that the
following tools and supplies are at hand.
• Gloves
• Safety Glasses
• Phillips screwdriver
• Non-corrosive leak-check solution
• Wrenches
A. DESIGN AND INSTALLATION
CONSIDERATIONS
C. INSPECT THE APPLIANCE AND
COMPONENTS
B. TOOLS AND SUPPLIES REQUIRED
The Outdoor Greatroom Co.
disclaims any responsibility for,
and the warranty will be voided by,
the following actions:
Asphyxiation Risk:
Sharp Edges:
WARNING
WARNING
WARNING
WARNING
WARNING
• Installation and use of any damaged
components.
• Modification of the assembly.
• Installation other than as instructed by the
Outdoor Greatroom Company.
ANY SUCH ACTION MAY RESULT IN A FIRE HAZARD
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
• Do not install damaged, incomplete, or
substitute components. Report damaged parts to
your dealer.
• Carefully remove all components from
packaging.
• Read all instructions before beginning
installation. Follow these instructions carefully
during installation to ensure maximum saftey and
performance.
• This gas appliance is to be vented outdoors.
• This unit must NOT be installed inside an
unvented appliance.
Wear protective gloves and safety glasses
during installation.
Vented Decorative gas appliance: NOT a source
of heat; NOT for use with solid fuel.
Do NOT use this appliance if any part of it has
been underwater. Have an authorized service
technician inspect the appliance and replace
any part of the control system and any gas
control which has been underwater.

8www.outdoorrooms.com HGI-31 : 1-23-2018
10”
MIN
6”
MIN
6”
MIN
10”
MIN
36”
MIN
TOP OF
APPLIANCE
OPENING
3
4
Additional Items Required
Framing Clearances
Some parts may have become damaged during shipment. Visually inspect every element for damage
before installation. NEVER install a damaged component. Review the Limited One Year Warranty found
on page 28 and 29 of this manual.
• Log set
• Glowing ember material
• Glass media
• Remote transmitter
• Power cord
• Manual gas valve shut o
• Vent Connection Tool
• Front surround kit - sold separately
• Venting system - 3” ex system
• Direct vent cap
• Phillips screw driver
• Flat-head screw driver
• 5/16” Hex driver
A. PACKING LIST B. ADDITIONAL ITEMS REQUIRED:
FIRE RISK
PROVIDE ADEQUATE CLARANCE:
CLEARANCES:
WARNING WARNING
• Around air openings
• For service access
• Locate appliance away from traffic areas
Inlet Exhaust
Minimum clearance to combustible side-walls:
6 inches
Minimum clearance to ceiling combustibles:
36 inches
Minimum clearance to front of appliance:
10 inches
(Img. 1)
INSPECTION OF APPLIANCE AND COMPONENTS
Minimum clearance to mantel:
12 inches for a 10 inch deep mantel
(Img. 2)
10”
MIN
6”
MIN
6”
MIN
10”
MIN
36”
MIN
TOP OF
APPLIANCE
OPENING
10”
36”
12”
10”
MIN
6”
MIN
6”
MIN
10”
MIN
36”
MIN
TOP OF
APPLIANCE
OPENING
mantel
ceiling

9
HGI-31 : 1-23-2018 www.outdoorrooms.com
5
Gas Hookup and Information
FIRE RISK FIRE RISK
CHECK FOR GAS LEAKS
EXPLOSION RISK: VERIFY INLET PRESSURES EXPLOSION RISK
EXPLOSION RISK
FIRE RISK
ASPHYXIATION RISK
WARNING WARNING
WARNING
• High pressure may cause over-re
condition.
• Low pressure may cause explosion
• Verify minimum pressures when other
household appliances are operating
Install regulator upstream of valve if line pressure
is greater than 10.5 in WC for natural gas and 14
in WC for LP gas.
• Gas build-up during line purge may
ignite
• Purge should be performed by authorized
technician
• Ensure adequate ventilation
• Ensure there are no ignition sources such as
sparks or open flames
• Check all ttings and connections
• Do not use open flame
• After the gas line installation is complete, all
connections must be tightened and checked
for leaks with a commercially available leak-
check solution. Be sure to rinse off all leak-
check solution following testing.
Fittings and connections may have loosened
during shipping and handling.
Before making gas connections, ensure the
appliance being installed is compatible with the
available gas type.
NOTE: Have the gas supply installed in accordance
with local building codes, if any. Installation should
be done by an authorized installer approved and/
or licensed as required by the locality.
Incoming gas line should be piped to the
12.7mm (1/2 inch) connection on the manual
shut-o valve.
A small amount of air will be in the gas
supply lines. When rst lighting appliance it
will take a short time for air to purge from
lines. Subsequent lighting of the appliance
will not require such purging.
Proper input pressures are required for optimum
performance and safety. Gas line sizing
requirements need to be made following NFPA-
54.
Pressure requirements for appliance are shown
in table below. Minimum pressures must be
met when other household gas appliances are
operating.
A. FUEL
C. GAS CONNECTION
B. GAS PRESSURE
PRESSURE NATURAL GAS PROPANE
Min. inlet pressure 5 inch WC
10.5 inch WC
10.5 inch WC
14 inch WC
Max. inlet pressure

10 www.outdoorrooms.com HGI-31 : 1-23-2018
WARNING
WARNING
WARNING
IMPROPER INSTALLATION,
ADJUSTMENT, ALTERATION SERVICES,
OR MAINTENANCE CAN CAUSE INJURY
OR PROPERTY DAMAGE. REFER TO
AND UNDERSTAND THIS MANUAL.
FOR ASSISTANCE OR ADDITIONAL
INFORMATION CONSULT A QUALIFIED
INSTALLER, SERVICE AGENCY,
LICENSED TECHNICIAN OR THE GAS
SUPPLIER.
The installation must conform with local codes or, in the absence of local codes,
to the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or the National Gas and Propane Installation Code, CSA B149.1
Your gas fireplace insert was built for Natural
Gas use. If you are converting from one fuel
source to another, you must reference the
specific Conversion Kit Instructions supplied
with the Conversion Kit. CONVERSION
Kits MUST be installed by QUALIFIED
INSTALLERS.
NATURAL GAS CONVERSION KIT:
PART NUMBER: HGI-16
LIQUID PROPANE CONVERSION KIT:
PART NUMBER: HGI-17
AN APPROVED REGULATOR, IF NEEDED,
MUST BE FITTED BY THE INSTALLING
PLUMBER.
WARNING
CHECK ENTIRE SYSTEM FOR LEAKS
BEFORE OPERATING. IF AN INSTALLER IS
CONVERTING THE UNIT FROM NATURAL
GAS TO LP, RE-CHECK ALL CONNECTIONS
FOR LEAKS BEFORE USE.
• The LP gas supply used with LP congurations
must be constructed and marked in accordance
with the specications for LP gas
• Cylinders must be stored outdoors in a well-
ventilated area out of the reach of children.
Disconnected cylinders must have threaded
valve plugs tightly installed and must not
be stored in a building, garage, or any other
enclosed area.
• The LP gas supply system must be arranged
for vapor withdraw.
D. LP GAS SETUP
GAS SETUP FOR LIQUID PROPANE

11
HGI-31 : 1-23-2018 www.outdoorrooms.com
WARNING
WARNING
IMPROPER INSTALLATION,
ADJUSTMENT, ALTERATION SERVICES,
OR MAINTENANCE CAN CAUSE INJURY
OR PROPERTY DAMAGE. REFER TO
AND UNDERSTAND THIS MANUAL.
FOR ASSISTANCE OR ADDITIONAL
INFORMATION CONSULT A QUALIFIED
INSTALLER, SERVICE AGENCY,
LICENSED TECHNICIAN, OR THE GAS
SUPPLIER.
CHECK ENTIRE SYSTEM FOR LEAKS
BEFORE OPERATING. IF AN INSTALLER
IS CONVERTING THE UNIT FROM LP
TO NATURAL GAS, RE-CHECK ALL
CONNECTIONS FOR LEAKS BEFORE USE.
• The appliance and its appliance main gas valve must be disconnected from the gas
supply piping system during any pressure testing of that system at test pressures in
excess of ½ psi (3.5 kPa).
• The appliance must be isolated from the gas supply piping system by closing the
equipment shut-off valve during any pressure testing of the gas supply piping system at
test pressures equal to or less than ½ psi (3. kPa).
• Provide a 1/8-in NPT plugged tapping, accessible for test gage connection, immediately
upstream of the gas supply connection to the appliance.
1. Ensure that the HGI-31 is stable and level.
Verify that the Natural Gas injector is in place
and that the air shutter is 1/8” open. Adjust air
shutter by loosening the small screw on the air
shutter and rotating it to an 1/8” open position
and re-tighten screw.
2. Connect the metal flex-line included with your
insert to the incoming Natural Gas supply line
shut-off valve using two (2) wrenches to tighten.
3. Ensure that the manual shut-off valve is
placed on the Natural Gas line before it reaches
the appliance control valve.
E. NATURAL GAS SETUP
GAS SETUP FOR NATURAL GAS
• The Natural Gas supply must be properly sized
for use with this appliance.
• An adequate gas supply system must be in
place to provide gas to the replace without
aecting other gas appliances.
• Gas supply sizing must be done by a certied
professional.

12 www.outdoorrooms.com HGI-31 : 1-23-2018
WARNING
WARNING: Failure to install the parts in accordance with these directions or failure to use only parts
specifically approved with this appliance may result in property damage or personal injury.
6
Installation
• If any parts need to be removed, they should be removed in a manner that allows the unit to be
returned to its original condition in the event this insert is removed. A label is provided to position
in the interior rebox stating the replace has been altered and cannot be used for wood burning
unless it is returned to the original condition.
• The damper and grate, if present, must be removed form the wood burning replace. Other
parts as needed must also be removed, these can include: glass doors, smoke shelf, ash ledge,
refractory liner, screen. Nothing must be removed that weakens the structural strength or
integrity of the existing wood burning replace. A gas appliance must NOT be connected to a
chimney ue servicing a separate solid-fuel burning appliance.
• If the lower hearth of the unit is removed, the HGI-31 must be set on noncombustible material and
should be positioned so that appliance is not installed where carpet or other material will discolor
or ignite from radiant heat. See Page 7 for clearances.
• After removal of obstructions in the existing factory-built replace, you can now begin installation
of the HGI-31.
• Ensure accessibility of components for service when unit is installed.
• Installation and repair should be done by a qualied service person. The appliance should be
inspected before use and at least annually by a professional service person. More frequent
cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burners, and circulating air passageways of the appliance
be kept clean.
1. Install the two (2) 3-inch diameter ex lines
down your chimney. This is a dangerous
job - ensure you use all necessary safety
precautions to prevent falling from the roof.
2. Stretch the vent to the desired length.
3. Mark both ends of one ex line with the
word “EXHAUST” as to properly identify and
connect to the cap and the appliance.
4. Attach a rope to the end of the ex line with a
heavy object. Do not use anything that could
damage your chimney. The rope must be long
enough to reach into the rebox from your
rooftop.
STEP ONE: VENTING THE APPLIANCE
(Img. 3)
(Img. 4)
EXHAUST

13
HGI-31 : 1-23-2018 www.outdoorrooms.com
• The installer must mechanically attach the
marking supplied with the gas replace insert
to the inside of the rebox of the replace into
which the gas replace insert in installed
• Cutting any sheet-metal parts of the replace in
which the gas replace insert is to be installed is
prohibited.
• If the factory-built replace has no gas access
hole(s) provided, an access hole of 1.5 in (38.1
mm) or less may be drilled through the lower
sides or bottom of the rebox in a proper
workmanship like manner. This access hole
must be plugged with non-combustible
insulation after gas supply line has been
installed.
• The replace ue damper can be fully blocked
open or removed for installation of the gas
replace insert.
• The replace and replace chimney must
be clean and in good working order and
constructed of non-combustible materials.
• Refractory, glass doors, screen rails, screen
mesh, and log grates can be removed from
the replace before installing the gas replace
insert.
• Trim panels or surrounds shall not seal
ventilation openings in the replace.
• Ensure that chimney clean outs t properly.
• Smoke shelves, shields, and baes may be
removed if attached by mechanical fasteners.
• Ensure a tight connection is made between the
gas insert ue collar and replace chimney.
5. Slowly lower your rope down the chimney.
After the rope is inside the rebox, the installer
on the rooftop feeds the ex vent down the
chimney while a second person guides the
pipe through the chimney by pulling on the
rope from the interior of the house.
6. After both ex vents are in place, attach the
cap with the end you marked exhaust to the
exhaust terminal of the roof cap. The roof cap
can now be secured in place.
7. You can now complete the installation indoors
- connect the Termination Plate inside the unit
rst connecting the exhaust ex vent to the
exhaust side. (Img. 5-6) (clamps are provided
with vent kit and require either a 1/4” wrench or flat-
head screwdriver)
8. Press berglass insulation around the two vents, at
the damper level, to prevent cold air from entering
or hot air from escaping.
9. Attach the Termination Plate to the unit using two
(2) provided screws. (Img. 6)
(Img. 7)
(Img. 6)
(Img. 5)
EXHAUST
EXHAUST

14 www.outdoorrooms.com HGI-31 : 1-23-2018
1. Slide the appliance and vent connector
assembly into the wall cavity. (NOTE: Vent
connector assembly may be dicult to reach
depending on the opening height of the fireplace
cavity. An installation tool is provided to assist in
positioning the vent connection assembly.)
2. Position the appliance so that it is ush with the
exterior face of the replace cavity.
1. The appliance should now be tested to ensure
the gas supply and electrical connection have
been properly installed.
2. If you did not previously check for leaks, you
must remove the appliance from the wall
cavity at this time and perform a check for
leaks on all gas connections.
3. Use the manual switch and remote control unit
to ensure the appliance is properly operating.
4. Do not operate for more than two minutes
as the appliance will not properly exhaust at
this time without the front glass assembly
installed.
1. Fasten the Surround panel to the appliance
using the provided four (4) screws into the
upper and lower corners of the surround (Img. 8).
2. Following Step One, the appliance should
be positioned so that the surround is rmly
pressed against the exterior face of the
replace cavity.
STEP TWO: POSITIONING APPLIANCE
STEP THREE: TESTING THE APPLIANCE
STEP FOUR: ATTACHING THE SURROUND (Img. 8)
(Img. 9)

15
HGI-31 : 1-23-2018 www.outdoorrooms.com
1. Position the back log (A) as seen in Img. 10.
Press it in place such that the tabs secure it on
both ends. The log should be at against the
back of the rebox.
2. Position the two (2) larger side logs (B) and
(C) as shown in Img. 11.
3. Position the center log (D) over tube as seen in
Img. 11.
4. Position the ber embers over the porting - be
sure not to interfere with the pilot assembly.
Pull the material apart so it is light and thin
over the ports, it is not necessary to use all of
the material.
5. Position the glass embers over the LED tray.
Use all the glass embers, place them randomly
ensuring the darker side of the material is not
uniformly installed.
6. Position the last two (2) smaller logs (E) and
(F) to line up with the indentations for the
grate bar as shown in Img. 12.
STEP FIVE: LOGS AND EMBERS A
B
D
C
EF
(Img. 10)
(Img. 11)
(Img. 12)

16 www.outdoorrooms.com HGI-31 : 1-23-2018
1. Position the TOP two (2) slots over the tabs
on the appliance and press tight the bottom of
the glass as seen in Img. 13 and Img. 14.
2. Reach into the lower slot of the appliance and
grasp the spring-loaded glass clamps as seen
in Img. 15.
3. Pull the latch forward and up to latch the
hooks to the front.
4. Release the handle to secure the front.
5. NOTE: BOTH SPRING-LOADED GLASS
CLAMPS ARE NECESSARY FOR THE
APPLIANCE TO FUNCTION PROPERLY AND
SAFELY!
6. Press heat deector into position above glass
door assembly. (Img. 16)
STEP SIX: GLASS FRONT
WARNING
The glass front seals the front of the appliance
and provides relief in the event of a delayed
ignition. You must ensure it is correctly
installed for proper, safe operation!
• DO NOT USE SUBSTITUTE MATERIALS.
• DO NOT SLAM OR STRIKE GLASS.
• DO NOT OPERATE WITH BROKEN GLASS.
• DO NOT CLEAN WHEN HOT.
• DO NOT USE ABRASIVE CLEANERS.
(Img. 13)
(Img. 14)
(Img. 15) (Img. 16)

17
HGI-31 : 1-23-2018 www.outdoorrooms.com
1. The Vented Front Face with Integral Screen
can now be placed on the mounting brackets.
2. Align the tabs of the Safety Screen with
their associated mounting brackets on the
appliance. (Img. 17)
3. Lower the assembly into place. (Img. 18)
4. The safety screen is now installed. (Img. 19)
STEP SEVEN: SAFETY SCREEN
(Img. 17)
(Img. 18)
(Img. 19)
NOTE TO THE INSTALLER
COMPLETE ALL VERIFICATION TESTING PRIOR TO TURNING OVER THE UNIT TO THE
HOME OWNER. FOLLOW THE SECTION “LIGHTING AND OPERATION” BEFORE LIGHTING.
BE SURE TO READ ALL WARNINGS AND SAFETY PRECAUTIONS.
• If the screen becomes damaged, the
screen shall be replaced with the
manufacturer’s barrier for this appliance.
• In case of glass breakage, notify
the manufacture for new glass front
assembly. DO NOT ATTEMPT TO
REPLACE THE GLASS PANEL.
• THIS APPLIANCE IS NOT INTENDED
FOR USE WITH GLASS DOORS.
• A barrier designed to reduce the risk
of burns from the hot viewing glass
is provided with this appliance and
shall be installed for the protection of
children and other at-risk individuals.
• If the barrier becomes damaged, the
barrier shall be replaced with the
manufacture’s barrier for this appliance.

18 www.outdoorrooms.com HGI-31 : 1-23-2018
1. Install remote control batteries (Battery Type:
CR2450). Test the remote control from various
locations within the room - a blue light on the
remote will indicate the remote is working.
2. Select remote operation on the replace switch, see
Img. 22.
3. Push the button shown on Image 20.
4. Press the ON button on the replace remote.
5. A series of two (2) beeps will be heard from the
control module of the replace. An additional beep
will indicate that the unit is searching for a remote
signal to operate.
6. Remote is paired with the replace.
7. Turn on the main burner - this will take a few
minutes for its initial burn. It is necessary that air
bleeds out of the gas line on its initial start-up.
8. Once the pilot lights, the main burner of the
appliance will light. The glass will fog over from
moisture exhaust against the cold glass. This will
dissipate in a few minutes.
9. Allow the appliance to burn for a few minutes.
10. Adjust the ame height a number of times from
high to low. As the valve is adjusting, you will hear
a noise of the servo motor moving within the
appliance. When the valve has reached a maximum
or minimum value, the appliance will beep twice to
indicate the highest or lowest setting.
11. Adjust the fan control up and down. Similar to
the ame height adjustment, two beeps from the
appliance will alert you when the maximum or
minimum value has been reached.
12. Repeat for ember light adjustments.
1. With unit on, cycle down to the lowest ame setting
using the SMALL FLAME button. Two beeps will
indicate lowest ame setting.
2. Press and hold the SMALL FLAME button. The
control module will beep twice and the light on
the remote will go out and come back on following
ONE beep from the control module.
3. Turn the unit o with the remote OFF button. Pilot
will remain lit.
1. With unit on, cycle up to the highest ame setting
using the LARGE FLAME button. Two beeps will
indicate highest ame setting.
2. Press and hold the LARGE FLAME button. The
control module will beep twice and the light on
the remote will go out and come back on following
TWO beeps from the control module.
3. Turn the unit o with the remote OFF button.
Pilot will no longer remain lit.
STEP EIGHT: FINAL VERIFICATION TESTING AND REMOTE FUNCTIONS
ACTIVATE PILOT ONLY OPERATION
DEACTIVATE PILOT ONLY OPERATION
POWER: ON
FLAME: UP
FAN: UP
LIGHT: UP LIGHT: DOWN
FAN: DOWN
FLAME: DOWN
POWER: OFF
(Img. 21)
FCC STATEMENT
Warning
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Attention:
Changes or modication not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
Note: This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
product generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this product does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
(Img. 20)

19
HGI-31 : 1-23-2018 www.outdoorrooms.com
WARNING
• DO NOT TRY TO LIGHT ANY APPLIANCE
• DO NOT TOUCH ANY ELECTRIC SWITCH
• DO NOT USE ANY PHONE NEARBY
• IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE - FOLLOW THE
GAS SUPPLIER’S INSTRUCTIONS.
• IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE LOCAL FIRE DEPARTMENT
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY
RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, AND/OR LOSS OF LIFE.
WHAT TO DO IF YOU SMELL GAS:
FOR YOUR SAFETY, READ BEFORE LIGHTING
7
Lighting and Operation
A. This appliance is lit electronically. When
lighting, follow these instructions exactly.
B. BEFORE LIGHTING, perform a smell test for
gas around the entire appliance. Be sure to smell
next to and around the base of the appliance -
some gas is heavier than air and will settle on
the floor.
C. Use only your hand to turn the gas control
knob on the gas supply (if equipped), never
use tools. If the valve will not turn by hand, do
not attempt to repair it. Call a qualified service
technician. Force or attempted repair may
result in a fire or explosion.
D. Do not use the appliance if any part has been
under water. Immediately call an authorized
service technician to inspect the appliance and
replace any part which has been under water.

20 www.outdoorrooms.com HGI-31 : 1-23-2018
LIGHTING INSTRUCTIONS
1. Turn ON/OFF switch to the ON position
3. Remote function
Remote Function
Off
On
(Manual Operation)
2. You will see or hear sparking occurring at
the electrode.
4. Standing pilot
WARNING
IN THE EVENT THE FLAME DOES NOT LIGHT:
1. Flip switch to the OFF position.
2. Wait 10 minutes.
3. Smell for gas before you re-attempt ignition.
(Img. 22)
(Img. 24)
(Img. 23)
(Img. 25)
POWER: ON
FLAME: UP
FAN: UP
LIGHT: UP LIGHT: DOWN
FAN: DOWN
FLAME: DOWN
POWER: OFF