Outwater architectural products alpha bed SBF User manual

architectural products
OUTWATER
by
L.L.C.
Architectural Products by Outwater assumes no liability for improper installation. Page 1
Stocked in: ° Single/Twin ° Single/Twin X-Long
° Double/Full ° Double/Full X-Long
° Queen ° King
ASSEMBLY INSTRUCTIONS
MODEL #SBF: STEEL BED FRAME
***15 YEAR WARRANTY ***
One universal bed frame for each of Single, Double, or Queen wall beds.
May be mounted in either vertical or horizontal modes.
A lightweight, universal, structural steel bed frame with double overlap steel stieners,
completed with fold-away leg system. Designed to exceed the strength of wood or
aluminum as well as residential and commercial specications.
Designed to Exceed International ISO 9002
Standards for residential specications

Architectural Products by Outwater assumes no liability for improper installation. Page 2
• Familiarize yourself with all of the components in the Steel Bed Frame and mechanism
cartons, as well as throughly study this manual so you may plan the steps required to
complete this project.
• Study all illustrations and plan drawings. Make sure that the space available is adequate
for the specied dimensions of the bed cabinet, both in the open and closed positions
(see cut list pages to cross check dimensions).
• Cabinet Panels may be constructed of Ply Core or Particle Board.
• Handles to pull the bed open are not provided. Select these from your local decorative
hardware supplier. Have them on site at the time of assembly.
• Check to be sure that all items are available
Steel Bed Frame and Mechanism
Cabinet Components and Hardware
Necessary Tools
• If you choose a horizontal bed orientation, a separate cut list is provided and assembly
diagrams are on page 18.
1. Prepare all wood or laminate cabinet components.
2. Mount Lift Mechanism.
3. Install spring in Lift Mechanisms.
4. Assemble the Bed Cabinet.
5. Attach Bed Cabinet to wall.
6. Assemble Steel Bed Frame to Bed Face Panels.
7. Install the Bed Face Panel in Cabinet.
8. Install Handles, Left Assembly, Mechanism Covers, Mattress
PROJECT START-UP
STEPS TO COMPLETE PROJECT

Architectural Products by Outwater assumes no liability for improper installation. Page 3
CARTON CONTENTS FOR
NOTE: Each Frame Carton contains one Single, Double, Queen or King Steel Bed Frame complete
with leg assembly and necessary hardware. Mechanism components are in separate carton.
Qty. Frame Carton Items Comments
2 Frame End Sections Identical Head & Foot
2 Frame Side Sections Identical, Right or Left
3(5) Stieners - Bed Face (King Size) Space Evenly Between Frame Sides
2 Fold-away Legs One Left - One Right
1 Leg Connector Rod Stabilizes and Eases Leg Operation
Hardware Card #3
14 Bolt 10-24 x 1/2” (M6 x 12mm) Black Bolt Frame Corners
2 Bolt 10-24 x 1-1/4” (M6 x 32mm) Black Bolt Leg Stop Foot Corners
16 Nut 10-24 (M6) Black Nylock Use with #1214 & #1213
4 Angle 1” x 1” x 1-3/4”(25 x 25 x 44mm) Black Use inside Frame Corners
2 1/2” x 3/4” (13 x 19mm) Round Black Cylinder Use with #1213 as Leg Stop
Hardware Card #4
2 1-1/2” x 5/16” (T1.5 x 40mm) Black Washer Secure Leg Inside Frame
2 1-1/2” x .765” (T2.5 x 40mm) Black Washer Secure Leg Inside Frame
2 1-1/2” x .765” (T2.5 x 40mm) Black Nylon Washer Between Left & Outside of Frame
2 Nut 5/16” (M8) Black Nylock Secure Leg Inside Frame
2 Bolt 1/4”-20 Black Hex Head Attach Leg to Leg Rod
2 Star Washer for #1210 Attach Leg to Leg Rod
Hardware Card #5
1 Nylon Web Strap with Buckle Secure Mattress to Bed Frame
2 3/4” x 1/4” (T1.5 x 25mm) Washer Secure Nylon Web Strap to Bed
Face Panel Under Mattress
2 #8 x 5/8” (M4 x 15mm) Wood Screw Secure Nylon Web Strap
Hardware Card #7 - King Size Includes 2 Bags
110 #8 x 5/8” (M4 x 15mm) Wood Screw Attach Steel Bed Frame to Bed Face
Qty. Mechanism Carton Items Comments
1 Left Mechanism - Right Side Attach to Right Side Panel
1 Lift Mechanism - Left Side Attach to Left Side Panel
2 #1 Bags Containing 9 Springs Each Install Correct Number in Each Mechanism
1 13” Plastic Pipe Used to Set the Lift Mechanisms
Hardware Card #2
10 Machine Screw 5/16-18 x 1-1/4” To Attach Lift Mechanism to Side Panels
4 Hex Head Bolt 5/16-18 x 1” Attach Mechanism to Frame Side Section
2 Allen Head Bolt 5/16-18 x 1” Position Mechanism Arm on Frame Side Section
16 Hex Head Nylock Nut Secure Bolts and Screws
1Allen Wrench 5/16” For Allen Head Bolts

Architectural Products by Outwater assumes no liability for improper installation. Page 4
COMPONENT LAYOUT
• The frame is adaptable as vertical or horizontal (side tilt) bed.
• Frame has mounting holes to use any of 4 Power Packs:
SBLM, SBLM-A, ACBM, GPLS
Frame laid out for assembly in the vertical orientation.
Frame laid out for assembly in the horizontal orientation.

Architectural Products by Outwater assumes no liability for improper installation. Page 5
CABINET CUT LIST (VERTICAL ORIENTATION)
FOR USE WITH LIFT MECHANISMS: SBLM
Numbers in parenthesis ( ) are millimeters.
For use with 13” (330) or 11” (279) Leg Assemblies
Cabinets using 13” (330) Legs use a 2” (51) Facia and 4” (102) Kick. See page 12 for details.
Single / Twin Bed
Mattress Size: 39”x 75” (990 x 1905)
12” (305) max thickness
Overall Cabinet Dimensions:
44-1/2”w x 83-1/4” h x 16”d (1130w x 2115h x 406d)
Protrusion From Wall: 85” (2146)
Cabinet Material: 3/4” (18) MDF or Plycore
Qty. Description Width Length Finish (Tape) Edges
2 Bed Face Panel 21-1/4” (540) 77-5/16” (1964) 4 Edges
2 Side Panel 16” (406) 83-1/4” (2115) 2 Long Edges
2 Headboard (1) & Top Panel (1) 14-1/4” (362) 43” (1092) 2 Long Edges
1 Top Facia with 13” (330mm) Leg
or Bottom Kick with 11” (279mm) Leg
2” (51) 43” (1092) 2 Long Edges
1 Bottom Rear Base 6” (152) 43” (1092) 2 Long Edges
1 Bottom Kick with 13” (330mm) Leg
or Top Facia with 11” (279mm) Leg
4” (102) 43” (1092) 2 Long Edges
Double / Full Bed
Mattress Size: 54”x 75” (1372 x 1905)
12” (305) max thickness
Overall Cabinet Dimensions:
59-1/2”w x 83-1/4” h x 16”d (1511w x 2115h x 406d)
Protrusion From Wall: 85” (2146)
Cabinet Material: 3/4” (18) MDF or Plycore
Qty. Description Width Length Finish (Tape) Edges
4 Bed Face Panel 14-3/8” (365) 77-5/16” (1964) 4 Edges
2 Side Panel 16” (406) 83-1/4” (2115) 2 Long Edges
2 Headboard (1) & Top Panel (1) 14-1/4” (362) 58” (1473) 2 Long Edges
1 Top Facia with 13” (330mm) Leg
or Bottom Kick with 11” (279mm) Leg
2” (51) 58” (1473) 2 Long Edges
1 Bottom Rear Base 6” (152) 58” (1473) 2 Long Edges
1 Bottom Kick with 13” (330mm) Leg
or Top Facia with 11” (279mm) Leg
4” (102) 58” (1473) 2 Long Edges
Queen Bed
Mattress Size: 60”x 80” (1524 x 2032)
12” (305) max thickness
Overall Cabinet Dimensions:
65-1/2”w x 88-1/4” h x 16”d (1664w x 2242h x 406d)
Protrusion From Wall: 90” (2273)
Cabinet Material: 3/4” (18) MDF or Plycore
Qty. Description Width Length Finish (Tape) Edges
4 Bed Face Panel 15-7/8” (403) 82-5/16” (2090) 4 Edges
2 Side Panel 16” (406) 88-1/4” (2242) 2 Long Edges
2 Headboard (1) & Top Panel (1) 14-1/4” (362) 64” (1626) 2 Long Edges
1 Top Facia with 13” (330mm) Leg
or Bottom Kick with 11” (279mm) Leg
2” (51) 64” (1626) 2 Long Edges
1 Bottom Rear Base 6” (152) 64” (1626) 2 Long Edges
1 Bottom Kick with 13” (330mm) Leg
or Top Facia with 11” (279mm) Leg
4” (102) 64” (1626) 2 Long Edges

Architectural Products by Outwater assumes no liability for improper installation. Page 6
CABINET CUT LIST (VERTICAL ORIENTATION) - continued
*RECOMMENDED STIFFENER PLACEMENT FOR KING BEDS*
FOR USE WITH LIFT MECHANISMS: SBLM
Numbers in parenthesis ( ) are millimeters.
For use with 13” (330) or 11” (279) Leg Assemblies
Cabinets using 13” (330) Legs use a 2” (51) Facia and 4” (102) Kick. See page 12 for details.
Use 5-stieners total:
3 - equally spaced head to foot
2 - against inside of End Rail (foot end)
to provide added strength.
King Bed
Mattress Size: 76”x 80” (1930 x 2032)
12” (305) max thickness
Overall Cabinet Dimensions:
81-1/2”w x 88-1/4” h x 16”d (2070w x 2242h x 406d)
Protrusion From Wall: 90” (2286)
Cabinet Material: 3/4” (18) MDF or Plycore
Qty. Description Width Length Finish (Tape) Edges
4 Bed Face Panel 19-7/8” (505) 82-5/16” (2091) 4 Edges
2 Side Panel 16” (406) 88-1/4” (2115) 2 Long Edges
2 Headboard (1) & Top Panel (1) 14-1/4” (362) 80” (2032) 2 Long Edges
1 Top Facia with 13” (330mm) Leg
or Bottom Kick with 11” (279mm) Leg
2” (51) 80” (2032) 2 Long Edges
1 Bottom Rear Base 6” (152) 80” (2032) 2 Long Edges
1 Bottom Kick with 13” (330mm) Leg
or Top Facia with 11” (279mm) Leg
4” (102) 80” (2032) 2 Long Edges

Architectural Products by Outwater assumes no liability for improper installation. Page 7
CABINET CUT LIST (HORIZONTAL ORIENTATION)
#Qty. Description Single Double Queen Edge Band
1 2 Bed Face Panel 39” x 41-3/4”
(990 x 1060)
39” x 56-3/4”
(990 x 1441)
41-1/2” x 64-3/4”
(1054 x 1594)
4 Edges
2 2 Side Panel for 11”(280) Leg
Side Panel for 13”(330) Leg
16” x 47-3/4”
(406 x 1213)
16” x 49-3/4”
(406 x 1264)
16” x 62-3/4”
(406 x 1594)
16” x 64-3/4”
(406 x 1645)
16” x 68-3/4”
(406 x 1746)
16” x 70-3/4”
(406 x 1797)
2 Long Edges
2 Long Edges
3 1 Top Panel 16” x 78-1/2”
(406 x 1994)
16” x 78-1/2”
(406 x 1994)
16” x 83-1/2”
(406 x 2121)
2 Long Edges
4 1 Top Facia 2” x 78-1/2”
(51 x 1994)
2” x 78-1/2”
(51 x 1994)
2” x 83-1/2”
(51 x 2121)
2 Long Edges
5 1 Top Facia Stiener 3” x 78-1/2”
(76 x 1994)
3” x 78-1/2”
(76 x 1994)
3” x 83-1/2”
(76 x 2121)
2 Long Edges
6 2 Top Rear Stiener (1)
Bottom Rear Base (1)
4” x 78-1/2”
(102 x 1994)
4” x 78-1/2”
(102 x 1994)
4” x 83-1/2”
(102 x 2121)
2 Long Edges
7 2 Kick & Kick Stiener for 11”
(280) Leg
Kick & Kick Stiener for 13”
(330) Leg
2” x 78-1/2”
(51 x 1994)
4” x 78-1/2”
(102 x 1994)
2” x 78-1/2”
(51 x 1994)
4” x 78-1/2”
(102 x 1994)
2” x 83-1/2”
(51 x 2121)
4” x 83-1/2”
(102 x 2121)
2 Long Edges
2 Long Edges
8 1 Head Board 15” x 78-1/2”
(381 x 1994)
15” x 78-1/2”
(381 x 1994)
15” x 83-1/2”
(381 x 2121)
2 Long Edges
9 1 Head Board Stiener 6” x 78-1/2”
(152 x 1994)
6” x 78-1/2”
(152 x 1994)
6” x 83-1/2”
(152 x 2121)
0 Edges
10 1 Panel Connector 3” x 37”
(76 x 940)
3” x 52”
(76 x 1321)
3” x 58”
(76 x 1473)
0 Edges
Single Double Queen
Cabinet Size (D.W.H) 16” x 80” x 49-3/4”
(406 x 2032 x 1264)
16” x 80” x 64-3/4”
(406 x 2032 x 1645)
16” x 85” x 70-3/4”
(406 x 2159 x 1797)
Projection from Wall 49” (1245) 64” (1626) 70” (1778)
Max Mattress Size 39” x 75” (990 x 1905) 54” x 75” (1372 x 1905) 60” x 80” (1524 x 2032)
Max Mattress Thickness 12” (305) 12” (305) 12” (305)
Cabinet Components Description & Cut List (for both 11” & 13” legs). See pg. 18 for assembly.
Cabinet Material: 3/4”(19) MDF or Plycore Numbers in parenthesis ( ) are millimeters.
Cabinet Footprint Dimensions & Protrusion Distance from Wall (Horizontal)
Numbers in parenthesis ( ) are millimeters.

Architectural Products by Outwater assumes no liability for improper installation. Page 8
STEP-BY-STEP INSTRUCTIONS
STEP 1: MOUNT THE LIFT MECHANISM TO THE SIDE PANELS
1. Exactly mark the mounting holes on the inside of each side panel.
2. Drill a 1/16” (2mm) pilot hole for each mounting bolt. Drill the nal hole with a 5/16” (8mm) bit.
3. Countersink 5/8” (15mm) on the outside of the panels just deep enough for the 5/16” x 1-1/4”
(8 x 32mm) Machine Screws.
4. Mount the Lift Mechanisms.
NOTE: All location measurements are from the front edge of the Cabinet Side Panels.
Refer to Drawings 3 & 4.
Refer to Drawing 3, when using the 13” (330 mm) Leg
Refer to Drawing 4, when using the 11” (279mm) Leg
Drill Patterns in Drawings 3 & 4 are only for the SBLM Lift Mechanism
Number in parenthesis ( ) are millimeters.

Architectural Products by Outwater assumes no liability for improper installation. Page 9
STEP 2: INSTALL THE SPRINGS ON THE LIFT MECHANISMS
There are nine locations for springs. If the bed requires an even number of springs, do not use the
center hole (#5 from the top). If the bed requires an odd number of springs, start with the center hole
(#5 from the top) and work outward in both directions evenly.
Hook the springs so the open ends are facing outward. You may have to gently pry up the tension
arm and slide the spring under and snap them into place in the proper hole, matching the same
numbered hole from the top of the mechanism back plate. You should have an equal number of
springs on each side of the center hole.
Use the same number of springs and the same layout on both the left and right mechanisms.
SPRING APPLICATION CHART
Please Note: These are recommendations only. Actual number of springs required will depend
on the total weight of the bed-face unit including the mattress and all bedding.
BED SIZE BED PANEL MATERIAL
Plywood Core Particle Board
Single/ Twin 4-5 springs per side 5-6 springs per side
Double/Full 6-7 springs per side 7-8 springs per side
Queen 7-8 springs per side 8-9 springs per side
King 9 springs per side not recommended
After you have completed installing and checking the operation of your bed, you may nd it
necessary to add or remove springs to achieve the correct lift eort of between 5 to 10 pounds.

Architectural Products by Outwater assumes no liability for improper installation. Page 10
STEP 3: ASSEMBLE THE BED CABINET (VERTICAL ORIENTATION)
1. Locate the mounting position of the headboard marking the left and right side panels 20”
(508mm) from the oor and the 3”(76mm) in from the back edge of the panels. Note from
Drawings 6 & 7 that this mounts the bottom edge of the headboard out 3”(76mm) from the
back or wall edge of the Side Panels. Use the 1” x 1” x1-3/4” (25 x 25 x 44mm) mounting brackets
(2 each side). Be sure the top bracket is set low enough not to protrude beyond the back of the
cabinet. Use #8 x 3/4”(M4 x 19mm) Pan head Screws. The Headboard location may vary slightly;
just be sure it is secure and at the approximate 3”(76mm) distance from the back edge.
2. Use Angle Brackets to assemble Bottom Rear Base and Bottom Kick in position shown in
Drawings 6 & 7. Use two Angle Brackets on each end.
3. Attach Top Panel as shown in Drawings 6 & 7. Be sure back edge of the Top Panel is ush with
back of Side Panels and 1-1/4” (32mm) down from the top of the Side Panels so it is ush with the
bottom edge of the Top Facia. The Top Facia will cover the front edge of the Top Panel.
• If possible, the Bed Cabinet should be assembled in the room where it will be used.
• Be sure Lift Mechanisms are securely installed.

Architectural Products by Outwater assumes no liability for improper installation. Page 11
STEP 3: ASSEMBLE THE BED CABINET (VERTICAL ORIENTATION) - continued
Numbers in parenthesis ( ) are millimeters.
NOTE:
Top Facia and Bottom Kick cabinet parts are interchangeable for use
with either the 11” (279) Leg Assembly or the 13”(330) Leg Assembly.
Follow these directions:
When using the 11” (279) Bed Leg Assembly, use the 2”(51) tall board
as the Bottom Kick and the 4” (102) board as the Top Facia.
When using the 13” (330) Beg Leg Assembly, use the 4”(102) tall board
as the Bottom Kick and the 2” (51) board as the Top Facia.

Architectural Products by Outwater assumes no liability for improper installation. Page 12
STEP 4: ATTACH BED CABINET SECURELY TO WALL
1. Place cabinet against wall. Make sure the cabinet is level and square. Measure diagonally to be
sure of square. Bed will not operate if cabinet is not square. Check also for square from front to
back as well as side to side. Use shims where necessary.
2. Prior to placing cabinet against the wall, locate 3 studs or other wall frame members at the level
of the Top Panel (top of bed).
ALERT: The cabinet must be secured to studs or other wall structural members using 2” x 2”
(51 x 51mm) L-Brackets. If the wall is not a wood stud wall, use metal stud screws, toggle bolts or
concrete expansion bolts if necessary.
3. Now that the cabinet is square and plumb, use two #8 x 2” (M4 x 51mm) at head wood screws in
each of three 2”x 2” (51 x 51mm) brackets to attach to studs at the top level of the Top Panel (see
Drawing 9). Re-check square and plumb and then secure 2”x 2” (51 x 51mm) L-Brackets to Top
Panel with #8 x 3/4” (M4 x 19mm) wood screws. Attach warning label to top of cabinet. Attach
three Bumper Buttons to bottom of the front edge of the Top Facia. These Bumpers allow the Bed
Face Panel to close quietly.
• You may or may not wish to remove the Base Board to allow the Bed Cabinet to t ush against
the wall. If you do remove the Base Board, save for later trim and replacement. If you do not wish
to remove the Base Board, you may use a shim or ller strip of the same thickness at the top
between the cabinet and the wall.
HINTS: If the room is carpeted you may raise the kick up to 1/4” (7mm) to clear the carpet. More than
1/4” (7mm) will obstruct the operation of the bed.

Architectural Products by Outwater assumes no liability for improper installation. Page 13
STEP 5: ASSEMBLE STEEL BED FRAME TO FACE PANELS

Architectural Products by Outwater assumes no liability for improper installation. Page 14
STEP 5: ASSEMBLE STEEL BED FRAME TO FACE PANELS - continued
STEP 6: SET THE LIFT MECHANISM
1. Lay the Bed Face Panels down on a non-scratch surface such as a carpet or blanket.
2. Completely assemble the 4 Frame Sections with the corner brackets and the 3/16” x 1/2”
(M5 x 12mm) black bolts provided. Refer to Drawing 12 to properly place the leg stops at outer
right and left bottom holes at the foot of the bed frame.
3. Position the bed frame on the bed face panels. With the Head Frame section ush with the head
end of the Bed Face Panels. Refer to Drawing 10. Carefully attach the Bed Frame so it is centered
on the Bed Face Panels; you will have approximately 15/16” (24mm) space from the bed frame to
the panel edges right and left and at the bed foot.
NOTE: It is very important to have the Bed Frame centered on the Bed Face Panels. Any error will
be noticed in the vertical sight lines when the bed is closed.
4. Three steel stieners are provided for all beds (5 for King). These notched stieners should be
located and attached to divide the Bed Face length into four equal sections. Use caution not to
damage raised panels by putting screws in recessed areas. NOTE: King Beds have 5 stieners
(see diagram on pg. 6 for placement)
5. Attach the Nylon Web Strap approximately 18”(460mm) down from the foot of the bed and 6”
(150mm) in from the sides, for tucking in sheets. The Straps help secure the mattress in the
vertical position (see drawing 10).
Holding one foot against the bottom front edge of the side panel and using the 13”(330mm) PVC
tube, lever the tension arm out until you can set the arm lock to the hex nut at the hole A
(see drawing 13). This is the hex nut at the top front corner of the mechanism.
CAUTION:
If possible have a helper assist in the setting of the mechanism and loading of the bed face panel.
DO NOT reach behind the tension arm when you are doing the setting procedure.

Architectural Products by Outwater assumes no liability for improper installation. Page 15
STEP 7: INSTALL THE BED FACE PANEL UNIT
1. Insert Allen Head Bolts through Hole #1 (6-3/4” from end of side frame) on both left and right side
frames (see Drawing 14). Thread on 5/16”(8mm) Nylock nuts and securely tighten.
2. Insert two 5/16” (M8 x 20mm) Hex Head Bolts from the outside of the frame through Hole #3 and
put 5/16” (8mm) Nylock Nuts on these bolts only nger tight at this time.
3. Stand the Bed Face Panel in vertical position between the tension arms, lift evenly until the bolt
in Hole #3 drops in the slotted end of each tension arm. Gently tilt the bed face toward you until
the Allen Bolts in Hole #1 are completely seated in the bottom notch of the tension arms. Insert
the remaining 5/16”(8mm) Hex Head Bolts through tension arms into Holes #2 and fasten with
5/16” (8mm) Nylock Nuts; securely tighten these and the nuts on Hole #3.
4. When all bolts are securely tightened, you may tilt the panel outward to approximately 45
degrees to release the arm locks. You will hear a click as they disengage.
CAUTION:
Hold the Face Panel securely, DO NOT let it slam shut. Balance is not achieved until the mattress is
loaded in the bed.
Leveling of the bed cabinet is essential. Check the level both side to side and front to back. Proper
leveling will facilitate proper closure and exact sight lines of the t of the Face Panel to the Cabinet.

Architectural Products by Outwater assumes no liability for improper installation. Page 16
STEP 8: INSTALL HANDLES - LEGS - MECHANISM COVERS - MATTRESS
1. Position and secure handles for ease of operation. Measure down approximately 36”(914mm)
from the panel top to the top of the handles.
2. Install legs with the washers on the inside of the Rails and the Nylon washer on the outside.
Tighten nut to have a small amount of friction when leg assembly is rotated from the up to down
position.
3. Install leg connector rod between legs and secure with 1/4”x 1-1/4” (M4 x 32mm) Hex head bolts
and star washers. Be sure they are securely tightened so not to become loose.
4. Install the mattress and secure with previously installed Nylon Straps.
5. Snap the powder coated steel mechanism covers in place - secure with #8 x 1-1/4”(M4 x 32mm)
black wood screws through the stando on the backer plate.

Architectural Products by Outwater assumes no liability for improper installation. Page 17
COMPLETE BED ASSEMBLY
FOLLOW UP TO INITIAL ASSEMBLY
Check that the Bed Cabinet is level and square so the Bed Face has
equal clearance of the Cabinet on both sides, top to bottom. If the
Cabinet is leaning to one side, nudge it at the oor level. If the top
is uneven, place shims under the Side Panels. If bed is too heavy to
operate easily or slams shut, remove the Bed Face Panel and add or
subtract springs. At this time, you may decide to use one more or
less spring(s) on the left or right side Lift Mechanism.

Architectural Products by Outwater assumes no liability for improper installation. Page 18
BED ASSEMBLY (HORIZONTAL ORIENTATION)
It is recommended to reinforce
the vertical seam where the face
panels meet with a 3/4” x 3”
(18 x 76mm) wood stiener held
in place with wood screws to
the face panels. Use the steel
stieners as well; one next to
the wood stiener and the other
two equally spaced.
FOR POWER PACKS:
#SBLM:
Spring Balance Lift Mechanism
#SBLM-A:
Spring Balance Lift Mechanism Adjustable