Outwater EVOLVE HORIZONTAL User manual

INSTALLATION INSTRUCTIONS
EVOLVE
VERTICAL / HORIZONTAL
WALL BED HARDWARE
Architectural Products by Outwater, LLC.
24 River Road, P.O. Box 387, Bogota, NJ 07603-0387
Phone: [phone] • Fax: [phone]
www.outwater.com
Architectural Products by Outwater LLC | 1-800-835-4400 | outwater.com

Nx1
Ox1
Px2
Qx2
Rx1
Sx4
Tx2
Ux20
Vx12
Wx8
Xx3
Yx8
Zx4
AA x2
1
HARDWARE
Ax16
Bx16
Cx8
Dx4
Ex2
Fx6
Gx2
Hx2
Ix2
Jx2
Kx2
Lx8
Mx8
Threaded Insert
M8 x 16 Screw
M5 x 55 Screw
Nylon Washer
M8 x 40 Bolt
M8 Nut
Piston
Mattress Support
M5 x 10 Screw
Fastener
Bracket
Washer
M6 x 20 Screw
Wrench
Allen Key
Plate
Leg
Tube
M5 Nut
Flat Bar
5/8in x 15mm Screw
Door Bracket
1 3/4in x 44mm Bolt
2 3/4in x 70mm Bolt
Slat Cap
Slat
M5 x 30 Bolt
Architetural Products by Outwater LLC oers a 5 year limited warranty on slat bases used in the wall bed
as well as the mechanisms. The warranty covers the replacement of parts with manufacturing defects
and/or breakage caused by regular use. It does not cover damages caused by a poor installation or misuse
of the product. Professional installation suggested. The bed must be secured to the wall into wood or
metal studs.

2
290
155.50
196.50
64
64
28.50
83.50
290
354
450
244.50
179.50
DRILLING GUIDE
Front
Back
Bottom
All measurements are for 19mm (3/4’’) board.

3
Right side
Front
Front
Left side
Bottom
INSTALLING THE MOUNTING BRACKETS
1
A + B
A
P
B
P
Wood
ASSEMBLING THE CABINET
2
*
See conversion guide for suggested cabinet dimensions.

4
ASSEMBLING THE FRAME
4
3SECURING TO THE WALL
*
Professional installation recommended.
*
Needs to be secured into at least
two wood or metal studs.
L + M
K
4.1-
Attach the two half frames with X
4.2-
T to the frame with W
T
W
x3
X
x8
Tx2

5
5
6
MOUNTING THE FRAME ONTO THE MOUNTING BRACKET
I
J
S
x2
x2
x2
ATTACHING THE PISTONS TO THE FRAME
F= x2
Secure the shorter ends of the pistons to the frame
G= x2

6
Tilt the frame past the cabinet edge to mount the pistons on
the mounting brackets through the opening between the
slats
7INSTALLING THE PISTONS TO THE CABINET
Fx2
8INSTALLING THE STOPPER
Install the stopper (not included) on the
inside top of the cabinet where it will allow
cabinet.

7
9INSTALLING THE LEGS
F
D
E
R
Q
x2
x4
Install legs to bed frame.
Do not overtighten.
Install tube to both legs.
Q
6.1
6.2
E
AA
S
x2
x2
x2
10 INSTALLING THE DOOR BRACKETS
Vx12
Install the door brackets in alignment with the support
bars on the bed frame.
The door brackets must point downward
AA

8
11 INSTALLING THE DOORS
Hook the door brackets onto the frame and push down until
they click.
Attach the doors to the frame while putting weight on the frame to keep
the bed open.
C
U
C
Ux 20
x 8
11.1
11.2

9
INSTALLING THE MATTRESS SUPPORT
Insert the mattress supports into the
predrilled holes in the bed frame. H
12
13
Hx 2
INSTALLING THE SLATS
Place a cap on both ends of the slats. Insert
the slats into their designated holes along
the frame.
Y
Z
x8
x4
Y
Z

10
14 USING THE WALL BED
.
The wall bed is assembled and shown in lowered position.
Pivot the leg towards the inside of the unit.
Make sure leg is fully closed.
Pull up gently to close. Leg serves as mattress retaining system.
Pistons insure that door closes properly and remains closed.
.