Outwater TLL-ACTIV Series User manual

1
Please read this document carefully. If this desk is sold, please provide this manual to the buyer.
Use - Liability
This height adjustable desk has electric motors and is designed for use in dry work areas only. The desk height is
adjustable so that it can be positioned at the most ergonomically suitable height. Any other use is at user’s risk.
Under no circumstances does the manufacturer accept warranty or liability claims for damages caused from
improper use or handling of the desk frame.
Make sure no obstacles are in the desk’s path.
Make sure the desktop is not touching any walls.
Make sure all cords are appropriate length to accommodate the change in height.
Children should only operate desk under adult supervision.
There is a risk of injury and electric shock if not properly installed.
Keep liquids away from electrical components.
Do not sit or stand on the desk frame.
Do not crawl or lie under the desk frame.
Do not place any object taller than 508 mm (20”) underneath the desk .
Do not open any of the electrical components. There is a danger of electric shock.
This product is designed with a duty cycle of 10% (2min. on, 18 min. o).
In the event of a power outage or if the power cord is unplugged, a manual reset may be necessary
Weight capacity: 95 kg ( 209lb ).
1-
2-
3-
4-
5-
6-
7-
8-
9-
10-
11-
12-
13-
Caution!
In the event of a power outage or if the power cord is unplugged, a manual reset may
be necessary. Push and hold the arrows on the switch until the desk reaches its lowest
height, slightly rises and stops. Release the up & down buttons. Your desk is now ready
to use.
24 River Road, P.O. Box 500, Bogota, NJ 07603-0500
Phone: [phone] • Fax: [phone]
www.outwater.com
ARCHITECTURAL PRODUCTS by OUTWATER
ELECTRIC TABLE
Model: Activ / TLL-ACTIV-*
Assembly and instructions

2
Control switch
8x 10x
8x
4x
2x
Electrical Motor
1x
2mm
Parts Included
Structure
Frame
Hardware
Electrical components
5mm
1x
6x
Control Box and Power Cord
h l
m
n
o
i
j
k

3
Install the side supports on each side.
Assembly Instructions
Pivot each support at 90 degrees.
Step 1
Step 2
4x
4x
5mm
5mm
ni
ni
Tighten the screw
Deserrer la vis avant de pivoter si nécéssaire.
Loosen the screw before pivoting the leg if necessary.

4
Insert the cross support.
Step 3
Step 4
4x
5mm
n
8x
5mm
h
n
j
Complete this step for both legs
Do not screw in completely

5
Insert the shaft into the gearboxes mounted on the legs. Do not
tighten the set screws completely before the nal adjustments.
2mm
Map out the desired position of the legs. For maximum stability, center the legs on the table.
Adjustable width of 1050 mm to 1565 mm ( 41 3/8” - 61 5/8”). We suggest to use a tabletop with a minimum thickness of 25,4 mm (1”).
Step 5
Step 6
2mm

6
Step 7
Adjust the length of the legs and the shaft before you attach the table top.
Make sure no screws protrude from the shaft as they would rub against the
leg brackets during operation.
Please center the tubing for best results.
8x 6x
o
Insert the cover caps if necessary.
Step 8
Install the controller so it does not exceed the table top.
2x
l
Reserrer les vis de réglage
Tighten the set screws
l
Install the legs to the underside of the table top.
To Preset Heights:
Choose a comfortable height. Press one of the ‘‘M1, M2, M3 or M4’’
buttons and hold until the conrmation sound. Repeat the sequence
for the other desired heights.
4 personal height settings.
LED height readout.
Up-down.
2mm

7
Connect the control switch to the control box. Connect the motor to the control box.
Step 9
A
B