Ovela THEODORE OVTHEOGLKGA User manual

THEODORE GAS LIFT BED
KING
OVTHEOGLKGA, OVTHEOGLKCA, OVTHEOGLKBA

Ensure to read all instructions and warnings in this user guide prior to assembly.
When opening the packaging, ensure all components are accounted for. If components are
missing, contact help.Kogan.com for assistance.
Use a slightly damp cloth to wipe the surface.
SAFETY & WARNINGS
CLEANING & CARE
Note:
Do not use strong abrasive cleaners on this bed as it may result in damage.

AHeadboard (x1)
BFootboard (x1)
CLeft sideboard (x1)
DRight sideboard (x1)
ELong slat support (x2)
FShort slat support (x2)
GCentre slat support
(x2)
HSupport leg (x4)
IBed base (x1)
COMPONENTS

Hardware
1 Phillips head screw (x4)
2M8 nut (x22)
320mm screw (x24)
4M8 washer (x30)
540mm screw (x22)
6Allen key (x1)
7T-handle Allen key (x1)
8Bracket (x2)
9Foot (x4)
10 End cap (x24)
11 Slat (x36)
12 Inner cap (x24)
13 Lift handle (x1)
14 Mattress stopper (x1)
15 Screwdriver (x1)

Step 1: Using the screwdriver (15), secure the feet (9) onto the headboard (A) and footboard
(B) with four Phillips head screws (1).
1 (x4)
9(x4)
15 (x1)
ASSEMBLY
1
9
1
9
15
15
A
B

Step 2: Align the holes on the ends of the footboard (B) with those on the left and right
sideboards (C, D).
Align a bracket (8) onto the corner between the left sideboard (C) and footboard (B), then
using the Allen key (6), secure the bracket (8) with four 20mm screws (3).
Repeat this process on the other corner with the right sideboard (D) and footboard (B).
3(x8)
6 (x1)
8 (x2)
6
3
8
B
C
D

Step 3: Insert the long slat supports (E) into the short slat supports (F). Aligning the holes,
place two M8 washers (4) over top the two holes, then using the Allen key (6), secure with
two 20mm screws (3).
Repeat this process on the other corners to secure the long slat supports (E) into the short
slat supports (F).
3(x8)
4 (x8)
6 (x1)
6
4
3
E
E
F
F
E
F

Step 4: Align the holes of one centre slat support (G) with two support legs (H).
Over the holes, place four M8 washers (4) on top, then using the Allen key (6), secure four
40mm screws (5) through the washers (4). Using the T-handle Allen key (7), secure the
underside of the holes with four M8 nuts (2).
Repeat with the other centre slat support (G) and two remaining support legs (H).
2 (x8)
4 (x8)
5 (x8)
6 (x1)
7 (x1)
x2
G
H
H
6
4
5
E
H
2
7

Step 5: Align the holes on the ends of centre slat supports (G) with those on the short slat
supports (F).
Secure the two centre slat supports (G) to the short slat supports (F) using eight 40mm
screws (5), eight M8 washers (4), and eight M8 nuts (2).
This completes the slat support assembly.
2 (x8)
4 (x8)
5 (x8)
6 (x1)
7 (x1)
6
4
5
F
G
2
7
F
F
G
G

Step 6: Place the bed base (I) onto the bed assembly. Align the brackets on the left and
right sideboard (C, D) to the headboard (A) and footboard (B). Secure each bracket with
two 20mm screws (3).
3(x8)
6 (x1)
3
6
I
A
C
D
B

Step 7: Extend the gas lifts on the left and right sideboards (C, D).
D
C

Step 8: Place the slat support assembly onto the gas lifts and secure it in place using six
40mm screws (5), six M8 washers (4), and six M8 nuts (2) in the holes indicated in the
image below.
2 (x6)
4 (x6)
5 (x6)
6 (x1)
7 (x1)
6
4
5
E
E
E
2
7

Step 9: Connect three slats (11) using two inner caps (12) and two end caps (10) to create a
slat assembly. Repeat this process until you have twelve slat assemblies.
Secure the slat assemblies by aligning the holes on the end caps (10) and inner caps (12)
with the markers on the base assembly.
10 (x24)
11 (x36)
12 (x24)
10
11
12
11
12
11
10
x12
10
11
12

Step 10: Attach the lift handle (13) and mattress stopper (14) to the bed.
13 (x1)
14 (x1)
14
13

Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com