Overland Storage NEO 4000e User manual

Part Number 10400214-101 05/2009 ©2009 Overland Storage, Inc. Page 1 of 2
IMPORTANT: Overland Storage requires that all NEO
Series parts be removed and replaced by an Overland
Storage authorized service provider. Improper installation may
result in damage which voids existing warranties.
This document describes how to remove and replace the
chassis of a NEO 4000Elibrary from Overland Storage.
WARNING: The GUI touch screen does not completely
shut off NEO Series system power. To reduce the risk of
electric shock or damage, unplug both power cords.
Unpacking the Spare
Carefully unpack and verify that you have all the parts:
•NEO 4000Echassis
•One M3x8mm flathead Phillips screws
•Four M4x8mm flathead Phillips screws
•These instructions
Electrostatic Discharge Information
A discharge of static electricity can damage micro-circuitry
or static-sensitive devices. To help prevent Electrostatic
Discharge (ESD), observe standard ESD precautions.
1. If the library is operational:
a. Exit the application software and, if necessary,
stop the software services.
b. Using the Graphical User Interface (GUI) or the
application software, remove any cartridges from
the drives to prevent damage.
c. Use the GUI to remove all the magazines.
IMPORTANT: If the library is non-operational, the
doors can be manually opened by pushing a stiff
wire against the mechanical releases directly behind the
front panel (Figure 1).
Figure 1. Manual Door Release Locations
2. For a Master module, if possible, print the first few
pages of the Trace Log (up to the Factory Area) to
capture the current settings of the library. Log into
WebTLC and click History > Display Trace.
3. Power off the library as follows:
a. Use the GUI to power down the library.
b. Turn the power supply switches to OFF (O).
c. Remove the power cords.
4. Remove all external cables.
5. If XpressChannel is installed, release it by loosening
the four captive screws on the back side and, for a
Master unit, unplugging the DB-15 plug.
6. To reduce weight, we recommend removing the drive
assemblies.
WARNING: It is recommended that a mechanical
lifter (or at least two people) be used during rack
installation or removal to prevent injury.
7. Using a mechanical lifter (or two people), remove the
unit from the rack and place on a secure ESD surface.
8. Unpack the new chassis and place it next to the old
chassis on the ESD surface.
NEO®4000E
Spare Chassis
Remove & Replace Instructions
Overview & Notes
NEO-0157
Prepare the Library
NEO-0155
Manual Release

Part Number 10400214-101 05/2009 ©2009 Overland Storage, Inc. Page 2 of 2
Move XpressChannel Cover Plate
If the old library used the XpressChannel feature, move
the XpressChannel cover plate from the new chassis to
the old unit (Figure 2).
Figure 2. Removing the XpressChannel Cover
1. On the new unit, remove and discard the two screws
(located inside drive bays #2 and #4) that secure the
cover plate.
2. Remove and discard the top cover screw.
3. Remove and discard the two screws outside (next the
power supplies) that hold the cover.
4. Move the XpressChannel cover plate from the new
chassis to the old chassis.
5. Install a new M3x6mm flathead screw in the top hole.
6. Install two new M4x8mm flathead screws inside
drive bays #2 and #4.
7. Install two new M4x8mm flathead screws on the
outside (next the power supplies), securing the cover.
Reinstall the Library
1. Using a mechanical lifter (or two people), reinstall the
library into the rack.
2. If removed, reinstall the drive assemblies.
3. If used, reconnect the XpressChannel and, for a
Master unit, plug in the DB-15 cable.
4. Reconnect the external cables.
5. For SCSI systems, verify the terminators are still in
place.
6. Manually open the doors and reinstall the magazines.
Power On the Library
1. Plug in the power cords.
2. Turn the power supply switches to ON (|).
3. Press the GUI touchscreen to power on the module.
Configure the Library
Depending on the type of module, do one of the following:
•For a Master/Standalone module:
a. Using the default Administrator password (“2”), log
on to WebTLC.
b. Using the printed partial Trace Log, reconfigure
the library to match its previous configuration.
c. Change the Administrator password.
d. If necessary, re-enter any feature key codes.
•For a Slave module, use the GUI to change it to Slave
mode.
NOTE: For full details, refer to the NEO 4000EUser Guide.
Return Old Chassis
Using the replacement part box and packing, return the
old chassis to Overland Storage.
Complete the Exchange
NEO-9198
M3x6mm
4x8mm
4x8mm
Locking Bracket
Additional Help
You can get additional technical support on the Internet at http://support.overlandstorage.com, or call
1-877-654-3429 (toll-free U.S. & Canada), [phone] (Europe), or [phone] Option 5 (International).