OWC data doubler User manual

DATA DOUBLER
Installation Guide

OWC Data Doubler
Introduction........................................................................ 1
1.1 Minimum Requirements
1.2 Package Contents
1.3 About This Manual
Installation..........................................................................3
2.1 Mounting a 2.5" SATA Drive to the Bracket
2.2 Installation by Laptop type
2.2.1 - Late 2008 13” MacBook (5,1) and Mid-2009 13” MacBook Pro (5,5)
2.2.2 - Late 2009 13” MacBook (6,1) and Mid-2010 13" MacBook (7,1)
2.2.3 - Mid-2010 13” MacBook Pro (7,1)
2.2.4 - Early / Late 2011 13” MacBook Pro (8,1) and Mid-2012 13” MacBook Pro (9,2)
2.2.5 - Late 2008 15” MacBook Pro (5,1), Mid-2009 15" MacBook Pro (5,3 and 5,4)
2.2.6 - Mid-2010 15” MacBook Pro (6,2)
2.2.7 - Early / Late 15” MacBook Pro (8,2) and Mid-2012 15” MacBook Pro (9,1)
2.2.8 - Early / Mid 2009 17” MacBook Pro (5,2)
2.2.9 - Mid-2010 17” MacBook Pro (6,1) and Early / Late 2011 17” MacBook Pro (8,3)
Support Resources..........................................................77
3.1 Troubleshooting
3.2 Contacting Technical Support
OWC Data Doubler Table of Contents
Contents

OWC Data Doubler Introduction
1
1.1 Minimum Requirements
• MacBook 13” (Late 2008, Late 2009, Mid 2010)
• MacBook Pro 13” (Mid 2009, Mid 2010, Early 2011, Late 2011, Mid 2012)
• MacBook Pro 15” (Late 2008, Mid 2009, Mid 2010, Early 2011, Late 2011,
Mid 2012)
• MacBook Pro 17” (Early 2009, Mid 2009, Early 2010, Early 2011, Late
2011)
• The Data Doubler works with 2.5 inch SATA drives (7mm or 9.5mm drive
height)
1.2 Package Contents
Installation screws (7)
OWC Data Doubler
5-Piece Toolkit
NOTE: Some kits do not come with a 2.5 inch SATA drive as pictured above.
1.3 About this manual
The images and descriptions may vary between this manual and the unit
shipped. Functions and features may change depending on the rmware
version. Please visit the product web page for the most recent product
specications.
Introduction

OWC Data Doubler Introduction
2
Your laptop is a static-sensitive device. It is susceptible
to invisible damage if not protected during installation.
We recommend proper grounding by using a
grounding strap. Make sure to work in a clean, static-
free area, and avoid wearing clothing that retains
static charges. For more information please visit:
www.owcdigital.com/support/anti-static

OWC Data Doubler Installation
3
2.1 Mounting a 2.5" SATA Drive to the Bracket
1. Align the drive to the connector on the green circuit board, then apply
gentle pressure in the direction shown below to fully connect the drive.
2. Use the two large, round-head Phillips screws from the kit to ax the drive
to the side of the Data Doubler bracket (screw hole locations shown in red).
The OWC Data Doubler and SATA drive are now ready for installation.
Installation

OWC Data Doubler Installation
4
2.2 Installation by Laptop type
2.2.1 Late 2008 13” MacBook (5,1) and Mid-2009 13” MacBook Pro (5,5)
IMPORTANT: before beginning, be sure that your laptop is fully shut down
and disconnected from all cables, including the power cable. If you have a
MacBook model 5,1, start with Steps 1-3. If you have a MacBook Pro model
5,5 start with Step 4.
1. Use the release lever (highlighted below in red) to release the battery cover,
then remove it (bottom photo). Recommended: Use the pull-tab on the
battery to remove it from the laptop, then set it aside.

OWC Data Doubler Installation
5
2. Next, remove the eight Phillips screws that secure the bottom cover to the
chassis (highlighted below).
Note: the three right-most screws along the top edge (shown in yellow)
are longer than the rest; install them in the same screw holes at the end of
the process. The rest can be used interchangeably in the remaining screw
holes.
3. Place your ngers on the bottom cover near the black vent opposite the
battery compartment, then lift the bottom cover. There are two snap clips
holding the cover in place; they will release when you lift the cover. Set the
bottom cover aside. You do not need to remove the SATA drive.
Proceed to Step 6.

OWC Data Doubler Installation
6
4. Remove the 10 Phillips screws from the bottom cover. Note: the three right-
most screws along the top edge (shown in yellow) are longer than the rest;
install them in the same screw holes at the end of the process. The rest can
be used interchangeably in the remaining screw holes.
5. Once the screws are removed, place your ngers along the bottom cover
near the black vent, then lift the bottom cover. There are two snap clips
attached to the cover that will release when you do this. Set the cover aside.
Recommended: before continuing, use the nylon pry tool to gently lift the
battery connector (highlighted in yellow) from the logic board.

OWC Data Doubler Installation
7
6. You should see the optical drive (indicated by the red arrow). This drive
needs to be removed before you can install the OWC Data Doubler.
7. Rotate the laptop so the optical drive is oriented in the same manner as the
drive shown below.

OWC Data Doubler Installation
8
8. Beginning on the right side of the optical drive, remove the two Phillips
screws that are highlighted in the photos below. Note: These screws are
not used when reassembling the laptop; store them in a safe place in case
you need them later.