Oxford Garden Dartmoor DMST User manual

Components
1Seat
QUANTITY: 1
2Front Right Leg
QUANTITY: 1
3Front Left Leg
QUANTITY: 1
4Rear Right Leg
QUANTITY: 1
D A R T M O O R S T O O L
I T E M - D M S T
O X F O R D G A R D E N
O X F O R D G A R D E N
1729 Research Drive, Unit A Louisville, Kentucky 40299
877.866.3331 (fax) 502.719.8888
Assembly Instructions page 1 Dartmoor Stool
5Rear Left Leg
QUANTITY: 1
Hardware
8mm dowels
QUANTITY: 14
Tools Components
A
6Foot Rest
QUANTITY: 1
Wood Glue
QUANTITY: 1
e
u
l
G
d
o
o
W
Wood Glue Brush
QUANTITY: 1
Finishing Items (included)
(included)
Medium Grit Sandpaper
NOTE: A hammer (not provided) will be needed for the assembly
of this bar chair.
GLUING INSTRUCTIONS:
Correct assembly of this chair requires glue to be applied to the final
assembly joints using the supplied glue. To properly glue these
joints follow the directions below:
a. Lay the assembly part flat and apply a liberal amount of glue into
the mortise using the brush and glue supplied. Use the brush to
make sure the glue is thick on the inside walls of the mortise.
b. Apply a liberal amount of glue to the complete tenon using the
brush to make sure the glue has contact with the entire tenon.
c. Assemble the parts as instructed in the instruction steps. After
assembling the glued parts, use a damp cloth or sponge to clean
up any excess glue from the outer surface of the furniture.
NOTE: If the furniture is going to be placed on concrete or tile patio,
it should first be rinsed well to remove the sawdust that may cause
some staining.
About Shorea Wood
Wood Care Instruction
Shorea is a tropical hardwood that is comparable to teak. Because of its high oil content it
is resistant to rotting, bug infestation, and the effects of wind, rain, sun, and snow. If left
untreated shorea weathers naturally to a beautiful silver gray color. Some surface
roughness may develop, especially at the end grain, but over a period of about one year,
the natural weathering process will stabilize. Moderate checking in the grain is normal
with exposure to the elements. Small surface cracks that may appear in no way affect the
structural integrity of the furniture. As weather conditions and temperatures fluctuate
these small cracks may expand and contract.
To prevent the staining of concrete or tile the furniture should be rinsed well after
assembly to remove dust that might remain from the manufacturing process. Although
shorea weathers well we recommend a routine application of teak oil or Cabot’s
Australian Timber Oil in extremely dry climates. A routine oiling is also recommended for
furniture to be used for dining purposes to discourage staining from food and drink spills.
For seasonal cleaning rinse the furniture well and then scrub (using a sponge or soft
bristle brush) with a mild solution of water, laundry detergent and a little bleach. Rinse
with fresh water.
To restore the original wood color, Oxford Garden suggests applying Cabot’s Australian
Timber Oil or any high quality teak oil after cleaning. Test in an inconspicuous spot first, to
approve the color. Application of oil is at the customer’s discretion and is not covered by
the warranty. Paint or any products with polyurethane are not recommended, as
application of these products will void the warranty as well.
For additional information regarding our warranty, please visit www.oxfordgarden.com

Assembly Instructions page 2 Dartmoor Stool
Step 1
On a clean flat surface, lay the right front leg 2 (front leg has
two lower mortise holes), and the right rear leg 4 (rear leg has
one lower mortise hole) on their sides mortise holes facing up.
Step 6
Enjoy your new bar stool!
Step 2
Line up the seat 1 , and insert into the legs.
Step 4
Place the left front leg 3 and the left rear leg 5 onto the
parts already assembled.
Step 3
Line up the foot rest 6 , and insert into the legs.
Step 5
With a hammer, drive 12 total dowels Ainto the predrilled holes on
the inside of the front and rear of the legs as shown. Insert the tapered
end of the dowels first. NOTE: The dowels should be easily driven in
flush. If there is strong resistance, do not force the dowel. Sand to
smooth off areas around the dowel pins.
A
3
5
* Apply glue in this step. * Apply glue in this step.
* Apply glue in this step.
* Apply glue in this step.
* See page 1 for gluing instructions.
4
6
2
3
5
1