Oxford Garden FRANKLING FRCH User manual

FRANKLIN ROCKER
I T E M - F R C H
O X F O R D G A R D E N
O X F O R D G A R D E N
1729 Research Drive, Unit A Louisville, Kentucky 40299
877.866.3331 (fax) 502.719.8888
Assembly Instructions page 1 Franklin Rocker
Components
1Right Arm Assembly
QUANTITY: 1
2Left Arm Assembly
QUANTITY: 1
7Front Seat Rail
QUANTITY: 1
Components
8 Back Seat Rail
QUANTITY: 1
Hardware
Dowel
QUANTITY: 22
A
Wood Screw
QUANTITY: 4
B
Tools (included)
Wood Glue
QUANTITY: 1
Wood Glue Brush
QUANTITY: 1
e
u
l
G
d
o
o
W
3Right Rocker
QUANTITY: 1
4 Left Rocker
QUANTITY: 1
6Back
QUANTITY: 1
5Seat
QUANTITY: 1
Finishing Items (included)
Medium Grit Sandpaper
NOTE: A hammer (not provided) will be needed for the assembly
of this bar chair.
GLUING INSTRUCTIONS:
Correct assembly of this chair requires glue to be applied to the final
assembly joints using the supplied glue. To properly glue these
joints follow the directions below:
a. Lay the assembly part flat and apply a liberal amount of glue into
the mortise using the brush and glue supplied. Use the brush to
make sure the glue is thick on the inside walls of the mortise.
b. Apply a liberal amount of glue to the complete tenon using the
brush to make sure the glue has contact with the entire tenon.
c. Assemble the parts as instructed in the instruction steps. After
assembling the glued parts, use a damp cloth or sponge to clean
up any excess glue from the outer surface of the furniture.
NOTE: If the furniture is going to be placed on concrete or tile patio,
it should first be rinsed well to remove the sawdust that may cause
some staining.
About Shorea Wood
Wood Care Instruction
Shorea is a tropical hardwood that is comparable to teak. Because of its high oil content it
is resistant to rotting, bug infestation, and the effects of wind, rain, sun, and snow. If left
untreated shorea weathers naturally to a beautiful silver gray color. Some surface
roughness may develop, especially at the end grain, but over a period of about one year,
the natural weathering process will stabilize. Moderate checking in the grain is normal
with exposure to the elements. Small surface cracks that may appear in no way affect the
structural integrity of the furniture. As weather conditions and temperatures fluctuate
these small cracks may expand and contract.
To prevent the staining of concrete or tile the furniture should be rinsed well after
assembly to remove dust that might remain from the manufacturing process. Although
shorea weathers well we recommend a routine application of teak oil or Cabot’s
Australian Timber Oil in extremely dry climates. A routine oiling is also recommended for
furniture to be used for dining purposes to discourage staining from food and drink spills.
For seasonal cleaning rinse the furniture well and then scrub (using a sponge or soft
bristle brush) with a mild solution of water, laundry detergent and a little bleach. Rinse
with fresh water.
To restore the original wood color, Oxford Garden suggests applying Cabot’s Australian
Timber Oil or any high quality teak oil after cleaning. Test in an inconspicuous spot first, to
approve the color. Application of oil is at the customer’s discretion and is not covered by
the warranty. Paint or any products with polyurethane are not recommended, as
application of these products will void the warranty as well.
For additional information regarding our warranty, please visit www.oxfordgarden.com

Apply wood glue provided and attach the left rocker to the left
arm assembly 2 .
Step 1
Insert front seat rail into arm assembly.
Step 4
Attach the rocker then secure it by hammering two dowels into
each join. After the glue has set for at least 30 minutes but before it
hardens, clean the excess glue from the join with a clean cloth or knife. D
Step 2
Assembly Instructions page 2 Franklin Rocking Chair
Step 5
4
7
2
eu
l
G
d
oo
W
eu
l
G
d
oo
W
4
eu
l
G
d
oo
W
eu
l
G
d
o
o
W
On a clean flat surface, lay left arm assembly flat on the ground. With
mortise holes facing up, insert back assembly into arm assembly.
NOTE: The top of the back is marked and should be placed at the top
of the chair.
Step 3
6
6
Insert the back seat rail into arm assembly.
NOTE: The back rail is shorter than the front rail. The tenons
of both rails are angled. Position the rails so that the tenons point
to the back of the rocker.
8
8
7
A
AA
A
A
* Apply glue in this step. (See pg.1 for instruction.)

Step 6
Drive 16 wood dowels into place, with the tapered end first.
Step 8
Repeat Steps 1 and 2 for the right arm and then attach the right arm
assembly to the rest of the assembled parts.
Repeat Step 9 for both the left and right side.
Step 7
Assembly Instructions page 3 Franklin Rocking Chair
Step 8 (front view detail)
Step 9
Secure seat with 4 wood screws .
B
Step 9 (detail)
B
A
Put seat assembly into place, keeping the leg notches to the front of
the chair, and the rounded arch to the back.
5
A
A
A
A
A
A
A
A
A
A
1
1
5
B
B
B
B
B