Oxford Garden FRANKLIN ROCKER FRCHK User manual

15 Kingbrook Parkway, Suite 100
Simpsonville, KY 40067
p. 877.866.3331 f. 502.719.8888
oxfordgarden.com
FRANKLIN ROCKER - FRCHK
ASSEMBLY
INSTRUCTIONS
Ver. 2019.06.03
COMPONENTS HARDWARE
1
3
Right Arm Assembly
Quantity: 1
Right Rocker
Quantity: 1
2
Left Arm Assembly
Quantity: 1
B
4
Left Rocker
Quantity: 1
Dowels
Quantity: 28
A
Wood Glue
Brush
Quantity: 1
D
Wood Screws
Quantity: 4
B
eulGdooW
Wood Glue
Quantity: 1
C
FINISHING ITEMS
Medium Grit Sandpaper
NOTE: If the furniture is going to be placed on a concrete or
tile patio, it should first be rinsed well to remove the sawdust
that may cause some staining.
GLUING INSTRUCTIONS:
Correct assembly of this chair requires glue to be applied to
the final assembly joints using the supplied glue. To properly
glue these joints follow the directions below:
a. Lay the assembly part flat and apply a liberal amount of
glue into the mortise using the brush and glue supplied. Use
the brush to make sure the glue is thick on the inside walls of
the mortise.
b. Apply a liberal amount of glue to the complete tenon
using the brush to make sure the glue has contact with the
entire tenon.
c. Assemble the parts as instructed in the instruction steps.
After assembling the glued parts, use a damp cloth or
sponge to clean up any excess glue from the outer surface
of the furniture.
NOTE: A hammer (not provided) will be needed for the
assembly of this bar chair.
5
Seat
Quantity: 1
7
Front Seat Rail
Quantity: 1
6
Back
Quantity: 1
8
Back Seat Rail
Quantity: 1

STEP 4
Insert the back seat rail into arm assembly.
NOTE: The back rail is shorter than the front rail. The tenons
of both rails are angled. Position the rails so that the tenons
point to the back of the rocker.
INSTRUCTIONS
STEP 1 * Apply glue in this step. (See pg.1 for instruction.)
Apply wood glue provided and attach the left rocker to
the left arm assembly .
Ver. 2019.06.03
STEP 3
On a clean flat surface, lay left arm assembly flat on the
ground. With mortise holes facing up, insert back assembly
into arm assembly.
NOTE: The top of the back is marked and should be placed
at the top of the chair.
STEP 5
Insert front seat rail into arm assembly.
STEP 6
Put seat assembly into place, keeping the leg notches to
the front of the chair, and the rounded arch to the back.
2
eulGdooW
eulGdooW
eulGdooW
eulGdooW
4
2
STEP 2
Attach the rocker by fitting the front tenon first and then
the back. Secure it by hammering two dowels into each
join. After the glue has set for at least 30 minutes but
before it hardens, clean the excess glue from the join with a
clean cloth or knife.
Fit the front
tenon first
A
A
A
6
4
6
8
8
7
7
5
5

STEP 9
Secure seat with 4 wood screws .
STEP 8
Drive 16 wood dowels into place, with the tapered end
first.
INSTRUCTIONS
STEP 7
Repeat Steps 1 and 2 for the right arm and then attach
the right arm assembly to the rest of the assembled parts.
Ver. 2019.06.03

STEP 8 (front view detail)
STEP 9 (detail)
Repeat Step 9 for both the left and right side.
A
B

A
A
A
AA
A
A
A
A
A
B
B
B
B