Oxford Garden Siena Chaise Lounge SCL70 User manual

SIENA CHAISE LOUNGE
I T E M - S C L 7 0
O X F O R D G A R D E N
O X F O R D G A R D E N
1729 Research Drive, Unit A Louisville, Kentucky 40299
877.866.3331 (fax) 502.719.8888
Assembly Instructions page 1 Siena Chaise Lounge
Components
1Right Arm Assembly
QUANTITY:1
6Chaise Lounge Frame
QUANTITY: 1
Hardware
Short Bolt
QUANTITY: 4
Finishing Items (included)
Medium Grit Sandpaper
NOTE: A hammer and a phillips head screwdriver
(not provided) will be needed for the assembly of this chair.
NOTE: If the furniture is going to be placed on a concrete
or tile patio, it should first be rinsed well to remove the sawdust
that may cause some staining.
A
Long Bolt
QUANTITY: 2
B
Barrel Nut
QUANTITY: 2
D
Tools (included)
Allen Wrench
QUANTITY: 2
Components
Guiding Bolt
QUANTITY: 1
C
8Wheels
QUANTITY: 2
2Left Arm Assembly
QUANTITY: 1
3Arm Dowel
QUANTITY: 1
4Rear Leg Stretcher
QUANTITY: 1
5Back Rail
QUANTITY: 1
QUANTITY: 1
Hex Head Wrench
7Leg Assembly (Foot)
QUANTITY: 1
8mm Short Dowel
QUANTITY: 12
F
Washer (Big)
QUANTITY: 2
H
Washer (Small)
QUANTITY: 2
I
Hex Head Nut
QUANTITY: 2
J
Axel Bolt
QUANTITY: 2
K
8mm Long Dowel
QUANTITY: 6
G
Cap Nut
QUANTITY: 4
E
Wood Glue
QUANTITY: 1
e
u
l
G
d
o
o
W
Wood Glue Brush
QUANTITY: 1
About Shorea Wood
Wood Care Instruction
Shorea is a tropical hardwood that is comparable to teak. Because of its high oil content it
is resistant to rotting, bug infestation, and the effects of wind, rain, sun, and snow. If left
untreated shorea weathers naturally to a beautiful silver gray color. Some surface
roughness may develop, especially at the end grain, but over a period of about one year,
the natural weathering process will stabilize. Moderate checking in the grain is normal
with exposure to the elements. Small surface cracks that may appear in no way affect the
structural integrity of the furniture. As weather conditions and temperatures fluctuate
these small cracks may expand and contract.
To prevent the staining of concrete or tile the furniture should be rinsed well after
assembly to remove dust that might remain from the manufacturing process. Although
shorea weathers well we recommend a routine application of teak oil or Cabot’s
Australian Timber Oil in extremely dry climates. A routine oiling is also recommended for
furniture to be used for dining purposes to discourage staining from food and drink spills.
For seasonal cleaning rinse the furniture well and then scrub (using a sponge or soft
bristle brush) with a mild solution of water, laundry detergent and a little bleach. Rinse
with fresh water.
To restore the original wood color, Oxford Garden suggests applying Cabot’s Australian
Timber Oil or any high quality teak oil after cleaning. Test in an inconspicuous spot first, to
approve the color. Application of oil is at the customer’s discretion and is not covered by
the warranty. Paint or any products with polyurethane are not recommended, as
application of these products will void the warranty as well.
For additional information regarding our warranty, please visit www.oxfordgarden.com

Step 1
On a clean flat surface, lay chaise lounge frame flat on its back.
Apply the glue provided in the mortise holes on the back rail and the
tenons on the chaise frame as shown.
Step 4
Align the right arm assembly to the chaise lounge frame by attaching
the front section of the arm to the large arm dowel and attach the back
leg section of the arm to the rear tenon of the chaise lounge frame.
NOTE: You may need to turn the chaise frame on its side to attach the
arms or prop the head of the chaise to attach the arms.
Assembly Instructions page 2 Siena Chaise Lounge
6
Step 2
Step 3
Insert the arm dowel 3 but do not attach it yet.
3
1
1
e
u
l
G
d
o
o
W
eu
l
G
d
o
o
W
GLUING INSTRUCTIONS:
Correct assembly of this lounge requires glue to be applied to the final
assembly joints using the supplied glue. To properly glue these
joints follow the directions below:
a. Lay the assembly part flat and apply a liberal amount of glue into
the mortise using the brush and glue supplied. Use the brush to
make sure the glue is thick on the inside walls of the mortise and has
made contact with the entire tenon.
b. Assemble the parts as instructed in the instruction steps. After
assembling the glued parts, use a damp cloth or sponge to clean
up any excess glue from the outer surface of the furniture.
Once you have applied the glue, insert the back rail into the the
chaise frame and secure by driving 2 long dowels into the
back rail as shown.
5
5
6
G
G
G

Assembly Instructions page 3 Siena Chaise Lounge
Step 5
To secure right arm to the chaise body, first insert long bolt into the front upright
of the arm connecting it to the chaise body by inserting a barrel nut through the
bottom of the chaise as shown in the detail figure below. Then hammer two short
dowels through the back leg section and one dowel through the front arm section
to secure it to the large arm dowel. NOTE: Use the extra long bolt provided as a
guiding bolt in this step. See instruction at bottom.
B
F
D
C
B
D
F
F
Step 5 (detail)
B
D
F
F
How to align barrel nuts and bolts.
Insert a guiding bolt into the end of a barrel nut. Align the barrel nut inside of the component with the bolt used to connect the components. Once the component bolt is aligned and threaded, simply pull the guiding bolt from the end of the barrel nut.
Step 6
Insert rear leg stretcher into the right rear leg as shown, and repeat
Step 5 to attach the left arm assembly. Once the left arm is in place, drive
two short dowels into each rear leg section to attach the rear leg
stretcher to the rear legs.
4
4
F
F
F

Step 7
Assembly Instructions page 4 Siena Chaise Lounge
Step 9
Drive 2 long dowels through the arm dowel to secure it to the
chaise lounge frame.
Step 8
7
7
7
8
8
8
AE
Attach the front leg assembly to the body of the chaise
using four short bolts and cap nuts as shown.
To attach the wheels, place axel bolt through wheel hole. Slide the
largest washer onto bolt. Next slide the bolt through the leg from the
outside. Slide smaller washer onto bolt. Place hex head nut onto
bolt and tighten with the hex head wrench provided.
Repeat procedure for other wheel.
H
IJ
K
G
G
G
A
A
E
E
H
H
I
I
J
J
K
K