Oxgard Praktika K-01 Quick start guide

Operational
manual
www.oxgard.com
[email protected]
Tel.[phone]
Praktika K-01 card collector

Operational manual 3
CONTENTS
1. Product purpose………………………………………………………....5
2. Delivery set............................................................................................... 5
3. Basic specifications.................................................................................. 6
4. Product design.......................................................................................... 7
6. Safety requirements.................................................................................. 9
7. Operation of card collector..................................................................... 10
7.1. Startup ............................................................................................. 10
7.2. Working modes ............................................................................... 10
7.3. Removing guest cards from card reader ......................................... 12
7.4. Inversion of LED panel board........................................................ 12

Praktika K-01 card collector 4
List of abbreviations
PS –power supply
ACS –access control system
OD –operating device
Firmware version FW v1.52

Operational manual 5
1. Product purpose
Card reader is designed for collection and storage of proximity
access cards at the exit from the facility. Flexible logic of operation and
connection of controller of the card reader allow it to be integrated with
any type of access control system.
2. Delivery set
Table 1. Delivery set
Item
Qty, pcs.
Praktika K-01 card collector
1
Hatch key lock
2
Datasheet
1
Operational manual
1
Installation guidelines
1
Anchors SORMAT PFG LB12-50*
3
Screw М12х60 DIN912(GOST 11738-84) with hexagon
hole for wrench*
3
Connecting cable PVA 2x1,5*
1
*- optional
The manufacturer reserves the right to change the packaging, specifications and appearance
without notice

Praktika K-01 card collector 6
ATTENTION (!) Reader doesn’t include in scope of supply.
3. Basic specifications
Table 2. Basic specifications
Specification
Value
Dimensions (WхHхD), mm
200х1045х200
Weight, kg
24
Temperature range,, ºС:
-operation
-transportation and storage
+1…+40
+1…+40
Atmosphere relative humidity, no more than %
80
Supply voltage, V:
- nominal
- working
12
8…18
Average current in standby mode * A
0,2
Maximal current *, A
1,5
Maximal dimensions, mm
155х40х55
Number of cards
More than 500
Lifetime, years
8
* - values mentioned at a nominal supply voltage
The manufacturer reserves the right to change the packaging, specifications and appearance
without notice

Operational manual 7
4. Product design
Fig 1. General view of card collector
The housing is made of brushed stainless steel. In front of the
housing there is a hatch with lock for quick access to collected cards and to
the board where PS, OD and ACS cables are connected. The hatch
includes a card storage device. The lower part of housing is equipped with
a hole for cables inlet.
ATTENTION (!) Reader is not included in the delivery set.
Customer can choose reader model suitable for the existing system.

Praktika K-01 card collector 8
The reader is mounted on a universal adjustable bracket, located
under the top cover of the card collector. This solution provides
maximum flexibility for installation and connection of the card reader.
5. Transportation and storage
Card collector in its original packaging shall be transported by air, by
road and by railroad with protection from direct exposure to rain and dust
without range limitation. It is allowed to stack boxes in 3 rows during
transportation and storage if Euro-pallets used. Keep the card collector in
dry (no moisture condensation) heated places within +1 to + 40 °C
temperature range. Avoid vapors of acids, alkalis, and corrosive gases at
the storage place. Storage of card collector in the original package in a dry
unheated premises or closed transport containers is permitted for short
periods, no more than 3 days. Before startup, the card collector must be
kept in a room with normal climate conditions for 12 hours after storage in
unheated rooms.
Dimensions of container - 345x345x1095 mm (HxWxL).

Operational manual 9
6. Safety requirements
CAUTION! Failure to comply with the safety requirements specified in
this section may result in damage to human life and health, total or partial
loss of workability of products and (or) auxiliary equipment.
CAUTION! Installation of the card collector shall be performed by
qualified personnel according to the instructions.
CAUTION! The producer disclaims any liability for damage to human life
and health, total or partial loss of workability of products and (or) auxiliary
equipment for non-compliance of the safety requirements specified in this
section, as well as terminate the product warranty.
IT IS NO ALLOWED TO:
Set the power supply unit inside the housing of the card collector, as
this could lead to electric shock to persons;
Set the card collector other than in dry and heated places;
Impede or accelerate the curtain of card reader;
Apply chemically aggressive cleaning detergents (as pastes and
liquids) to the materials of the housing.

Praktika K-01 card collector 10
7. Operation of card collector
7.1. Startup
Connect the power supply unit to network 220V and turn it on. Card
collector will beep and red cross will turn on LED panel (Fig. 1). Card
collector is ready for operation.
7.2. Working modes
Standby mode
The mode is set after power-up. In this mode, the card collector waits
for a signal from ACS controller. Red cross is turned on on the display.
The mode of minimal power consumption.
Passage with permanent cards
When an authorized permanent visitor card is presented to the reader
card collector unlocks the speedgate for the time specified by ACS
controller (depending on the operating mode; for 5 seconds in pulse
mode). During the specified time interval other cards are not accepted.
When the passage is performed or the specified time interval is expired
card collector switches into standby mode and can collect the next card.
Green arrow turns on on the LED panel, indicating the authorization of the
passage.