Ozobot EVO User manual

Too Sharp! Just Right Just Right
Too Thin! Too Thick! Inconsistent! Just Right
Too Close! Just Right
COLOR CODE TIPS
PAPER
CALIBRATION
DRAWING
LINES
Press & hold Ozobot’s
Power Button for 2-4
sec. until top light
blinks white. Then,
release Power Button.
Ozobot blinks green when
calibrated. If Ozobot blinks red,
start over from step 1. Evo also
spins during calibration.
Make sure Ozobot is
powered off, then
place it in a black circle
slightly bigger than
Ozobot. If you are
using markers, create
this circle using a black
marker.
Press the Power Button to turn Bit back on.
Evo powers on automatically after calibrating.
1
2
34
ozobot.com © Ozobot Inc.
X
2-4 sec.

Codes on black lines
Ozobot Markers
Crayola Classic
Crayola Pastels
Sharpie Chisel Tips
(use light green and
light blue)
Single color squares
approx 1/4”
All other codes need black line
before and after
Two-color codes need to
be at line end
White spaces
Codes on
colored lines
Too dark
Single color squares
larger than 1/4”
Overlapping colors
Different sizes
Codes on corners Keep codes on straight lines
away from corners
Codes too close
Too close to
intersection
Codes at least 1” apart
Place codes away
from intersections
Dry Erase
Colored pencil
DRAWING
COLOR
CODES
MARKERS
STICKERS
COLOR
CODE
PLACEMENT
To draw any Color Code, you will need a
combination of black, red, green and
blue markers.
Crayons
Highlighter
Codes on
colored lines
GO STRAIGHT
Not lined up
GO STRAIGHT
Codes on
corners
GO STRAIGHT
Align with straight,
black lines
At least 1-inch from
corners, intersections,
and other codes
Too close
GO LEFT
GO LEFT
ozobot.com
© Ozobot Inc.

These calibration dots can be re-used for play on
paper with Evo or Bit. Cut along the dotted lines
and fill circles in with black marker.
Note: Do not laminate as your bot cannot
properly calibrate on a laminated surface.
How to Calibrate:
1. Make sure bot is powered off, then place it in
the black circle.
2. Press & hold bot’s Power Button for 2-4 sec.
until top light blinks white. Then, release
Power Button.
3. Your bot blinks green when calibrated. If bot
blinks red, start over from step 1. Evo also
spins during calibration.
4. Press the Power Button to turn Bit back on.
Evo powers on automatically after calibrating.
CALIBRATION DOT
Fill in with
black marker
Fill in with
black marker
How to Calibrate:
1. Make sure bot is powered off, then place it in
the black circle.
2. Press & hold bot’s Power Button for 2-4 sec.
until top light blinks white. Then, release
Power Button.
3. Your bot blinks green when calibrated. If bot
blinks red, start over from step 1. Evo also
spins during calibration.
4. Press the Power Button to turn Bit back on.
Evo powers on automatically after calibrating.
CALIBRATION DOT
How to Calibrate:
1. Make sure bot is powered off, then place it in
the black circle.
2. Press & hold bot’s Power Button for 2-4 sec.
until top light blinks white. Then, release
Power Button.
3. Your bot blinks green when calibrated. If bot
blinks red, start over from step 1. Evo also
spins during calibration.
4. Press the Power Button to turn Bit back on.
Evo powers on automatically after calibrating.
CALIBRATION DOT
© Ozobot Inc. ozobot.com
Fill in with
black marker
CALIBRATION DOT
TEMPLATES