OZTI OME 4070 User manual

PASTA COOKER (ELECTRICAL)
USER’S MANUAL
PRODUCTION YEAR: SERIAL NO
PRODUCTION SITE : Cumhuriyet Mah. Eski Hadımköy Yolu No:29/A Büyükçekmece İstanbul/TÜRKİYE
Phone : [phone] (8 Lines) Fax : [phone]
PUBLISHED ON :01.01.2013 VER:V13.01 Page1 of 15
Our website: www.oztiryakiler.com e-mail: [email protected]
MANUFACTURER :ÖZTİRYAKİLER MADENİ EŞYA SAN. VE TİC A.Ş.
ozti

TABLE OF CONTENTS
PAGE NR. TOPICS
1COVER PAGE
2TABLE OF CONTENTS
3INTRODUCTION
4TECHNICAL DATA
5ELECTRICAL CIRCUIT DIAGRAM
6 - 7 MAIN DIMENSIONS AND WARNING SIGNS
8SAFETY DETAILS
9TRANSPORTING AND MOVING
10 INSTALLATION OF THE APPLIANCE
11 CONTROL BOARDS
12-13 OPERATION OF THE APPLIANCE
14 CLEAN-UP AND MAINTENANCE
15 TERMS OF WARRANTY
2/15
CAUTION
This applıance should only be used in facilities where relevant standards,
laws and safety requirements are complied with

INTRODUCTION
☞Please read and ensure that your operation personnel also reads this user’s
manual care fully before installing and using the appliance. If the appliance is
operated without reading the user’s manual, the appliance will not be covered
by the warranty.
☞The manual containing information about installation, usage and maintenance
of our product you purchased should be read carefully. Please ensure that
power supply connections to the appliance are already installed by qualified
personnel according to local legislation, before our authorized service
personnel arrives for the installation of the appliance.
☞If you are confused or you don’t have enough information
please get in touch with authorized service by phone.
☞Please keep in mind that, if the service personnel is delayed
at your site, related expenses and delay costs will be charged to
you on hourly basis.
☞We hope that you will get the best performance from our product…
Dear User,
Thank you for purchasing our appliance and for your reliance upon our
company. Our appliances are used in professional kitchens in 100
countries.
Our appliances are produced in compliance with international standards.
Important notice: Please read and ensure that the users read this user’s
manual in order to achieve the desired performance in line with your
expectations and to use your appliance for long years. Please take the
warnings mentioned above into consideration before calling for service...
3/15

TECHNICAL DATA
4/15
YOUR PRODUCT'S TYPE
OME 4070 OME 8070 OME 4090 OME 8090 OME 4060
MAIN DIMENSIONS (mm) 400X700X280 800X700X280 400X900X850 800X900X850 400X700X240
TOTAL ELECTRICAL INPUT
(KW) 5,5 11 12 24 4,5
POWER SUPPLY VOLTAGE (V) 380-400 380-400 380-400 380-400 230
WORKING FREQUENCY (Hz) 50-60 50-60 50-60 50-60 50-60
THERMOSTAT (°C) 30-115 30-115 30-115 30-115 30-115
SUPPLY CABLE (H 07 RNF) 5 X 2,5 5 X 4 5X4 5X4 3 X 2,5
CLASS 5° 5° 5° 5° 5°
MAXIMUM SLOPE 1 1 111
PROTECTION CLASS IP 21 IP 21 IP 21 IP21 IP 21

ELECTRICAL CIRCUIT DIAGRAM
5/15
C1: Contactor R1: Resistance
S1: Water On/Off Switch T1: Temperature regulator (On-Off)
H2: Thermostat lamp H3: Limit Thermostat Lamp
L1: Limit Thermostat V1: Water Inlet valve
V1

MAIN DIMENSIONS
6/15
OME 4070 OME 8070
OMFE 4090 OME 8090
OME 4060

7/15
POWER NETWORK GROUNDING
PE
GROUNDING
OVERHEAT
POWER SUPPLY CONNECTIONS
380-400V 3 NPE / 50-60 Hz /
230 V NPE / 50-60 Hz MONOPHASE
VOLTAGE: 380-400 V
SUPPLY CONNECTION: TRIPHASE
GROUNDED
FREQUENCY : 50-60 Hz
POWER
WARNING SIGNS

8/15
SAFETY DETAILS
☞The applıance should only be operated under a
chimney hood.
☞Any kind of flammable solid and liquid material (cloths,
alcohol and derivatives, petrochemical products, wooden
and plastic materials, cutting blocks, curtains etc.) should
never be held near the applıance.
☞You can use this applıance simultaneously together
with other products of ours.
☞Do not clean up the applıance with pressure water
☞This applıance should be installed in line with
effective regulations and only be operated in well
ventilated places. Please refer to the instructions before
installing and operating the applıance.
☞This applıance is designed for industrial use and
should only be operated by personnel trained on the
applıance.
☞The applıance should not be handled by
unauthorized persons except for the manufacturer or
authorized service.
☞In case of fire or flame in the area where the applıance is
operated, act without panic, close gas valves, turn off the
power switches and use a fire extinguisher. Never use water
to extinguish the fire.

TRANSPORTING AND MOVING
SMALL UNITS:
☞Before transporting device should be
disconnected from power.
☞The device can be moved with man power
☞Do not hit or drop the device when moving.
9/15
CHANGING THE LOCATION;
MACHİNES İNSTALLED BY AN AUTHORİZED SERVİCE.CANNOT
BE MOVED ELSEWHERE, ITS POWER SUPPLY CABLES CANNOT BE
EXTENDED OR REPLACED EXCEPT BY AN AUTHORİZED SERVİCE.
BIG UNITS:
☞The device should be placed vertically on a palette with man
power.
☞Feet of the fork lift should be placed under the appliances.
☞If the transported distance is far, the machine should be
moved slowly and the appliances should be fixed on palette or
supported in order to prevent jolt.
☞Do not hit or drop the products when moving.

INSTALLATION OF THE APPLIANCE
10/15
If this applıance located near to any wall, separation, kitchen
furniture, decorative coating etc. the distance in between
should be min.20 cm. and if those are coated with fireproof heat insulating
material, the distance should be min. 5 cm. It is strongly recommended that fire
safety protection instructions are observed.
All of the items mentioned below in connection with the
installation of the applıance should be carried out by
authorized service personnel.
☞Workbench on which the applıance stands should be adjustable and
the applıance should be ensured to operate in a leveled position.
☞Power supply connection of the applıance should be checked by an
eligible electrician, and it should be connected to a fuse at a maximum
height of 170 cm.
☞Power supply connection should be made using a 30 mA current
leakage fuse as
a protection against current leakage danger.
☞Power installation to be used should be grounded by connecting it to a
grounding bar at the nearest panel.

CONTROL BOARDS
11/15
A : ON-OFF SWITCH+THERMOSTAT
B : SAFETY THERMOSTAT
C : TANK FILLING SWITCH
ALEFT RIGHT
LEFT&RIGHT A
B
B
C
A
WATER TAP

OPERATION OF THE APPLIANCE
12/15
1. Pasta cooker is used in kitchens of restaurants, fast food stands, canteens, hospitals
in order to cook.
Fill the basin with water up to the maximum level through the water filling tap.
2. Before initial use of the applıance, beginning with the pasta container the outer surface
should be wiped with a cloth soaked in warm water and soap.
NOTE: Do not use except purpose of use. The applıance should be operated by
qualified personnel knowing safety terms and technical specifications and who has
read the instruction manual.
Turn the on-off key on and set controlled thermostat to 100 ºC (green lamp will light)
When the water starts to boil, place the pastry on the basket into the basin.
Check the water level within the basin regularly. Insufficient water levels will cause
defects in the resistances and harm the applıance. Add required water from the water
filling tap.
Shake the basket from time to time during cooking without taking out of the basin, in
order to cook pastry well In doing so, pastry is protected from sticking together.
Thermostat can be set to stand-by position 50 °C and the water kept at this
temperature, between each cooking batch in order to keep the water warm and
allow it heat up the water to 90°C more easily and also in order to save energy. The
cooker should not be disconnected from power. During stand-by periods without
cooking operation, leaving the thermostat set to 90 °C, causes unnecessary energy
waste and unnecessary boiling of water as well.
Turn the thermostat to “0” position and turned the pasta cooker off after daily use.
It is recommended to operate the applıance between temperatures of
+5ºC +40ºC and in ambient humidity of maximum 65%.
CAUTION !
NEVER OPERATE YOUR DEVICE
WITHOUT GROUND CONNECTION.

13/15
OPERATION OF THE APPLIANCE
CAUTION! : The appliances should be installed and
operated as described in this user’s manual. If any failure
is encountered please contact our nearest authorized
service dealer.
WHEN THE APPLIANCES HAS A FAILURE ONLY
AUTHORIZED …………………… SERVICE DEALERS ARE
ALLOWED TO HANDLE THE APPLIANCES. IF ANY
PERSON OTHER THAN ONLY AUTHORIZED SERVICE
DEALERS HANDLE THE APPLIANCES, IT WILL NOT BE
COVERED BY THE WARRANTY.
NEVER ALLOW PEOPLE WHO ARE NOT AUTHORIZED TO
HANDLE THE APPLIANCES. OTHERWISE PRODUCER
COMPANY WILL NOT BE RESPONSIBLE FOR THE
CONSEQUENCES. DURING MAINTENANCE SERVICE
OUR AUTHORIZED SERVICE DEALERS SHOULD NOT BE
PROPOSED TO USE NON-ORIGINAL SPARE PARTS FOR
WHATSOEVER. INSTALLING ANY NON-ORIGINAL SPARE
PART TO THE APPLIANCE LEAVES THE APPLIANCE OUT
OF WARRANTY COVERAGE.

1. CLEAN-UP:
Before (before the power is switched on) and after the first use and every
subsequent use, outer surface of the applıance should be completely cleaned
up with sponge and liquid detergent and then wiped dry.
Do not use CHEMICAL CLEANINGAGENTS like hydrochloric acid or abrasive
cleaning agents.
2. MAINTENANCE:
Periodic maintenance should be carried out by a technician. It is
recommended to carry out maintenance at least every 6 months, depending
on the frequency of use. Periodic maintenance conducted by authorized
service personnel of ours is charged, even the guarantee period has not
expired.
CLEAN-UP AND MAINTENANCE
14/15
LIFE OF USE
applıances life of use is 10 year if it is used under recommended
conditions.

TERMS OF WARRANTY
15/15
1- Documents without sales date, factory and sales company
approval on, are not valid. In order to benefit from the warranty,
warranty document should be presented.
2- If the appliance is installed and operated following the
instructions in the installation, maintenance and user's manual,
it is warranted for failures sourcing from materials and
workmanship .
3- The failures within the scope of warranty, how and where
these will be eliminated, and the way and place of maintenance
is determined by ................
4- The warranty is only valid provided that the warranty terms
and the instructions in the installation, maintenance and user's
manual are fully complied with. The warranty is only valid for the
warranted appliance, and no other right or compensation for
some other thing may be claimed.
5- If the information about the kind and the type of the appliance,
serial numbers printed on the warranty document are scraped,
rubbed or changed, then the warranty is not valid.
6- The warranty covers only maintenance and repairing of
material or workmanship failure within the valid warranty period.
Failures and parts within the scope of the warranty are repaired
and replaced without any charge. Replaced parts belong to
................
7- The failures occurring in the appliance may only be handled
by service personnel authorized by ................ If people who are
not authorized handle the appliance, it will not be covered by the
warranty.
8- Installation should be carried out by authorized service
personnel and the service should be informed about the location
change of the appliance.
9- When any failure occurs during operation, authorized service
dealer should be contacted.
10-Warranty does not cover failures and damages resulting from
loading, unloading and shipping, which are outside the
responsibility of ................ Similarly, failures and damages
resulting from external factors are not covered.