OZTTER SA User manual

Instruction Manual
Instruction Manual
www.oztter.com
OZTTER
CORPORATION
www.oztter.com
OZTTER CORPORATION
SA Sanitary Cartridge Filter Housing
Instruction Manual

永阡鑫股份有限公司
[SA SANITARY CARTRIDGE FILTER HOUSING INSTRUCTION MANUAL]
www.oztter.com OZTTER CORPORATION | 永阡鑫股份有限公司
1
Contents
◎Notice………………………….……. 2 - 3
◎Know Your Product….…………. 4
◎Instruction Manual..……........... 5- 6

永阡鑫股份有限公司
[SA SANITARY CARTRIDGE FILTER HOUSING INSTRUCTION MANUAL]
www.oztter.com OZTTER CORPORATION | 永阡鑫股份有限公司
2
Notice
1. Please install and test the housing according to the product operation manual.
2. This product is designed for filter equipment used for water filtration only, please don’t use it on other
purpose to avoid danger.
3. This product is categorized as pressure vessel, only professional or well-trained person who can install
and operate it.
4. Please read through the instruction manual before moving, installation and using of this product.
5. Please check the product and make sure that there is no any damage or components lost before
installing it. If the product was damaged, deformed or leaking, please stop using the housing
6. Please make sure that if the fluid is suitable for the filter before use.
7. Please use the product according to the instruction manual and make sure that the design pressure
and the operating pressure are in the required range.
8. The filter housing must be installed and fixed on the le l ground. Please do not fix it on the vibration
ground.
9. Please do not open the top cover randomlybefore piping .
10. Installing the pressurecontrol valve is suggested to keep the water pressure in casethe suddenly
increased/ decreased water pressure happens

永阡鑫股份有限公司
[SA SANITARY CARTRIDGE FILTER HOUSING INSTRUCTION MANUAL]
www.oztter.com OZTTER CORPORATION | 永阡鑫股份有限公司
3
11. Please avoid rapid switching of ball valve and continuous countercurrent which may cause damage of
filter while using the product.
12. Be sure to release the pressure inside the filter housing completely before replacing filter cartridges.
Please be cautious with the possibility of fluid ejection when it is at a high temperature
13. Please use the suitable O-ring and check it regularly. Please replace it if necessary. Deterioration or
damage of the O-ring may cause fluid leakage.
14. The internal plastics components will deteriorate by long-term use. Please check it regularly and
replace it if deterioration or damage is found

永阡鑫股份有限公司
[SA SANITARY CARTRIDGE FILTER HOUSING INSTRUCTION MANUAL]
www.oztter.com OZTTER CORPORATION | 永阡鑫股份有限公司
4
Know Your Product
No.
名稱
Description
No.
名稱
Description
No.
名稱
Description
1.
束環
Clamp
2.
排氣口
Vent
3.
桶體
Shell
4.
濾芯
Filter Cartridge
5.
桶唇
Shell flange
6.
墊片
Gasket
7.
底座
Base
8.
出入水口
Inlet / Outlet
9.
出入水口
Inlet / Outlet

永阡鑫股份有限公司
[SA SANITARY CARTRIDGE FILTER HOUSING INSTRUCTION MANUAL]
www.oztter.com OZTTER CORPORATION | 永阡鑫股份有限公司
5
Instruction Manual
1. Fix：
a. Fix the filter on the ground or a proper board.
2. Pipe：
a. Connect ⑦Base with ⑧⑨Inlet/Outlet and the main pipe.
b. Install the exhaust valve and pressure gauge at ②Vent
3. Open the filter and install the internal component：.
a. Unfasten and remove ①Clamp. Remove ③Shell..
b. Direct ⑤Shell flange at the central hole on ⑦base .
c. Check the ④Gasket, make sure it is in the groove.
d. Put ③Shell from the top down in parallel and place on the top of ⑥Gasket.
e. Open the ①Clamp, align it to the connection of the ⑥Base and ③Shell and lock the ①
Clamp tightly.
f. Lock the plum-type lock screw tightly in clockwise direction.
4. Testing：
a. Open ②Vent and pour water in till the water full out of the port. Close ②Vent
b. Check whether there is any leakage.
5. Stop Leaking：

永阡鑫股份有限公司
[SA SANITARY CARTRIDGE FILTER HOUSING INSTRUCTION MANUAL]
www.oztter.com OZTTER CORPORATION | 永阡鑫股份有限公司
6
a. If the liquid leak out, pleaseclose ⑧Inlet and unfasten ②vent to release the inner pressure.
b. Unfasten ①Clamp, and fasten is again. Open ⑧Inlet, add pressure slowly and check if
there is any leakage.
c. When the liquid stops leaking out, please open ⑧Inlet/Outlet to start the filter.
6. Stop running：
a. To stop the product operating, please close ⑫Inlet and ⑬Outlet first to stop the flow inside.
b. Open ②Vent to release pressure slowly.
c. Make sure inner pressure is released clearly and remove the shell.