PACH & COMPANY AeGIS 7000 Series Assembly instructions

AeGIS 7000 Series
Installation and Programming Manual
October 01, 2001
Pach & Company 941 Calle Negocio Phone: [phone]
www.pach-co.com San Clemente, CA 92673 Fax: [phone]

TABLE OF CONTENTS
Limitations of Liability
Chapter 1. Getting Started ............................................................................................. 1
1.1. Introduction .................................................................................................................................. 1
1.2. System Description, Specifications and Accessories .................................................................. 1
1.3 Unpacking the System ................................................................................................................. 2
1.4 Warranty ........................................................................................................................................3
Chapter 2. Installation .................................................................................................... 4
Chapter 3. Programming ................................................................................................ 7
3.1. Local Programming Via Built-in Keypad ...................................................................................... 7
3.2. Remote Programming Via a Touch Tone Phone ......................................................................... 7
Programming Function Codes .......................................................................................... 8
* ............................................................................................................................. 8
# ............................................................................................................................. 8
00 Replace System Master Code ................................................................. 8
01 Program a New Tenant ............................................................................ 9
02 Modify an Existing Tenant Directory .........................................................10
03 Delete an Existing Tenant Directory .........................................................11
04 Clear All Tenants Directory .......................................................................11
05 Manual Lock (open) or Unlock (Close) Door ............................................12
06 Selecting Directory Digits .........................................................................12
07 Single or Multi Systems ............................................................................13
08 System Number ........................................................................................13
10 Change the Welcome Screen ..................................................................13
46 System Information .................................................................................. 14
50 Clear the Memory to Factory Default .......................................................14
70 Change Talk Time .....................................................................................15
71 Change Door Open Interval .....................................................................15
72 Change Lock Out Count .......................................................................... 15
73 Select Tone or Pulse Dialing ................................................................... 16
74 Enable or Disable Auto Answer .............................................................. 16
75 Turn On or Off Key Press Beep .............................................................. 16
76 Turn On or Off Speaker Beep ................................................................. 17
77 Enable or Disable Remote Access ......................................................... 17
78 View Directory by Name ......................................................................... 17
91 Exit from Remote Programming ............................................................ 18
Chapter 4. System’s Operation ..................................................................................... 19
How to View the Tenant Name .......................................................................................................... 19
How to Initiate a Call and Unlock the Door for Visitor ....................................................................... 19
How to Extend the Talk Time ............................................................................................................. 19
How to Call into The System ............................................................................................................. 19
How to Provide Remote Access ........................................................................................................ 20
How to Disable Remote Access ........................................................................................................ 20
How to Call to a Voice Mail or Extension Number ............................................................................ 20
How to Use the 4-Digit Access Code to Unlock the Door ................................................................. 20
How to Adjust the Speaker and Microphone Volume ....................................................................... 20
How to Adjust the LCD Display ......................................................................................................... 20
How to Adjust the Pulse Sensitivity ................................................................................................... 20
How to Check the Number of Tenants Programmed in the System .................................................. 20
Chapter 5. Trouble Shooting Guide .............................................................................. 21
General FCC Requirements .......................................................................................... 24
Quick Guide .................................................................................................................... 25

LIMITATIONS OF LIABILITY
This manual is subject to change without notice.
Pach and Company is not liable for any errors that might occur from use of this document,
nor is any commitment to update the information herein implied.
Pach and Company does not assume any liability for any damages, which may arise in
installation or use of the AeGIS 7000 Series. Pach and Company does not assume liability for
any incompatibility between the AeGIS 7000 Series and users devices.
Pach & Company reserves the right to make changes without prior notice to any products in
order to improve reliability, function or design.

Chapter 1
GETTING STARTED
1.1 Introduction
Pach & Company thanks and congratulates you on the purchase of your AeGIS 7000 Series (7025, 7050, 7100, 7150,7200
or 7250) Telephone Access Control Systems.
The manual is designed to guide you through the proper programming and use of the AeGIS 7000 Series. It is important for
you to read and follow the manual completely.
The Aegis 7000 Series comes with two years warranty, but we are so confident in our product and our dealer's ability to
install them properly, we will include lightning strikes in our two years warranty if Pach and Company surge protector (ASP1)
is installed with the systems.
1.2 System Description, Specifications and Accessories
AeGIS 7000 Series utilizes microprocessor technology to provide security as well as convenience to you. It is designed for
residential and commercial buildings, military and government sites, industrial facilities, or any location where access control
is required. It uses a dedicated phone line and connects to the public telephone network. Authorization for access control is
through the telephone line, or with the tenant's own access code, which is entered on the system keypad. The tenants MUST
have a telephone to allow remote visitor access.
Also, as a standard feature, the tenant is allowed to "call" the Aegis unit and converse with the visitor and "remote
programming" using a touch tone phone.
The system parameters and tenants data will be entered via the keypad and the LCD provides easy display. EEPROM
technology is used for AeGIS 7000 series. The tenant database will not be lost during a power failure.
Standard features:
• Program and store the tenant's name, directory code, telephone number and personal access code.
• Unlocking door or gate remotely by the tenant using his or her telephone keypad.
• Unlocking door or gate by the tenant using his or her own private access code.
• Built-in back-light LCD directory, Postal Switch.
• Remote Phone Programming.
• Works behind a PBX to dial extensions (analog only).
• Keypad Activated to support Voice Mail.
• Programmable features:
• 2, 3 or 4 Digit Directory Code
• Lock Out Count
• Manual Unlock-Auto Countdown Re-lock.
• 4 Digit Unit master Code
• Open Interval
• Talk Time
Technical Specifications:
Power Input: 12 VAC 40 VA (supplied) or 12 VDC 40VA UL Listed Transformer
Current Consumption: 500mA idle, 700mA operation
Emergency Battery: 12Vdc, 4Ahr rechargeable (not supplied)
Telephone Line: Standard voice grade RJ11 jack.
Night Light:14V 0.080A 15,000 Average life hours.
Pach and Company Chapter 1 Page 1
AeGIS 7000 Series GETTINGSTARTED 10/01/01

Operating Environment: Temp. 32°F to +140°F Relative Humidity 0% to 95% non-condensing.
* Heater Pad (AHP5) is required if the ambient temperature is below 32°F.
Relay Output: Form C Dry Contact 120 VAC 10A/ 24VDC 10A/ 250VAC 7A
Memory Type: EEPROM
Tone Detection: Crystal controlled, capable of detecting short bursts 80 ms
Ringer Equivalence:0.6B
Mounting: Surface or Full-Flush.
Construction: 16-gauge stainless steel
Shipping: 11 lbs. or 5 kg. Approximate
Dimensions:10.75" (27.3Cm) x 8.5" (21.6Cm) x 3.125" (7.9Cm) (HWD)
Specifications subject to change without prior notice
Accessories and Replacement Parts:
1.3 Unpacking the System
After you unpacked the package, check the serial number on the printed circuit board, cabinet and warranty card, they must
match. If they do not match, please contact Pach and Company toll free number at [phone]. All the items listed below
come with the AeGIS 7000 Series. If you have missing items, please contact your distributor or Pach and Company at (888)
678-7224. • AeGIS 7000 Series System (7025, 7050, 7100, 7150, 7200 or 7250).
• XMFR (Power Transformer, 12VAC 40VA).
• 2-pin terminal connector (inside the cabinet)
• 4-pin terminal connector (inside the cabinet).
• 5-pin terminal connector (inside the cabinet).
• Key sets (2 keys per set)
• RJ-11 adapter (inside the unit's cabinet).
• Owners Manual.
• Warranty Card with unit's serial number.
Pach and Company Part Number Description
FFM7 Full flush mounting ring
ASP1 AC and Telephone Surge Protector
AHP5 Heater pad with Thermostat
APM1 AeGIS Pedestal Mounting Post for car and pedestrian
APM2 AeGIS Pedestal Mounting Post for semi-truck, car and pedestrian
APM3 AeGIS Pedestal Mounting Post for semi-truck.
AP7 Adapter plate for APM1, APM2 and APM3
XMFR Power Transformer
AVP7 AeGIS Video Package
AVP7C AeGIS Video Package (Color)
AVPX AeGIS Video Package Power Transformer
AKYS AeGIS key Sets (2 keys per set)
7MAN AeGIS 7000 Series Installation and program manual
ABAT1 AeGIS 12 VDC 4.5 Ahr battery backup
ABAT2 AeGIS 12 VDC 1.3 Ahr battery backup
Pach and Company Chapter 1 Page 2
AeGIS 7000 Series GETTINGSTARTED 10/01/01

1.4 Warranty
The AeGIS 7000 Series come with TWO (2) YEARS WARRANTYFOR MANUFACTURER’S PARTS AND
MANUFACTURINGLABOR.We will include lightning strikes in our two years warranty if our ASP1 surge protector is
installed with the systems. If you use other than Pach and Company ASP1 Surge Protector, you are responsible to claim the
damages to the surge protector manufacturer. The above warranties are subject to the following conditions.
• The serial number on the printed circuit board must match the serial number on the cabinet.
• The system's failure is not caused by vandalism, improper installation, misuse or abuse.
• Physically damaged product is not acceptable for repair or exchange within or after warranty.
• The warranty will be void and null if the product has been repaired or modified by unauthorized party without
authorization of Pach and Company Technical Department.
• If for some reason your system cannot be repaired, Pach and Company will replace it with an identical product of
equal value.
• You must obtain a Return Merchandise Authorization (RMA) number from Pach and Company Technical
Department before you can send back the product to factory for repair.
• You are responsible for all transportation and insurance charges for the products shipped to the Pach and
Company repair center.
• PACH AND COMPANY WILL NOT COVER THE FIELD LABOR TO INSTALL, REMOVE AND
TROUBLE-SHOOT THE SYSTEM.
Pach and Company Chapter 1 Page 3
AeGIS 7000 Series GETTINGSTARTED 10/01/01

Chapter 2
INSTALLATION
A proper installation of the AeGIS system is very essential. You MUST follow the installation procedures, block diagrams and
installation requirements as specified in this chapter.
Figure 2.1
Pach and Company Chapter 2 Page 4
AeGIS 7000 Series INSTALLATION 10/01/01
1
2
3
4
5
6
7

GROUNDING
Grounding the AeGIS steel enclosure is essential. Please comply with all local ordinances and industry standard
procedures to ensure a complete and safe ground. Recommended earth grounds are:
• Use 18-gauge solid wire for grounding.
• Installing a ground steel rod from the AeGIS steel enclosure to the earth ground.
• Installing a solid heavy gauge wire from the AeGIS steel enclosure to a water pipe.
• Connecting the AeGIS steel enclosure to any earth grounded steel metal.
TELEPHONE LINE
Always use AeGIS AC/Telephone Surge Protector (ASP1) to protect your investment. The Pach and Company “Two Years
Warranty” will include lightning if Pach and Company Surge Protector (ASP1) is installed. One surge protector must be
used for each AeGIS 7000 system. You must claim the damages to the manufacturer of the surge protector, if another
manufacturer surge protector is installed.
• Twisted pair category 5 is the minimum requirement if the distance less than 200 feet. Shielded wires are
recommended to avoid radio reception or any other noise problems. If the distance is more than 200 feet,
2-conductors, 18-gauge shielded stranded is recommended. Ground one end of the shielded to earth ground.
See installation instruction if ASP1 Surge Protector is used.
• If a PBX line is used connect the AeGIS to the analog PBX's extension to dial the extensions within the PBX.
Do not connect to a PBX's Digital Port.
NOTE:The AeGIS 7000 Series only works behind the PBX to dial extensions, no pause can be programmed on
the AeGIS 7000 to dial the outside line.
DOOR STRIKE OR ELECTRICAL STRIKE
The AeGIS 7000 series provides a single relay form "C" dry contact: Normally Open (NO) and Normally Closed (NC).
• 10 Ampere 120 VAC or
• 10 Ampere 24 VDC or
• 7 Ampere 250 VAC
See figure 2.1 for door strike wiring diagram. You MUST use two conductors 18 gauge stranded wire minimum.
Note: Some door strikes are creating electrical or magnetic noise or spikes and could create problem to the system's
memory. Although the system's relay has built-in filtration circuit, installing an isolation relay is recommended if the
system is experiencing with looses memory.
POSTAL LOCK
The AeGIS system comes with pre-wired "Normally Open" postal switch as shown on figure 2.2(a). If the postal switch is
pressed, the gate will open. If you need "Normally Closed" postal switch, see figure 2.2(b).
The postal lock is not included. You have to purchase the postal lock from your local post office. See figure 2.2 to alter the
postal switch to normally closed.
1
2
Pach and Company Chapter 2 Page 5
AeGIS 7000 Series INSTALLATION 10/01/01
3
4
Figure 2.2 (a) Figure 2.2 (b)
LCOM
POST
LCOM
POST

POWER
A 12 VAC 40VA transformer is supplied by Pach and Company. However, 12 VDC 40VA power supply or 12VDC power
supply with battery backup can be used to power the AeGIS 7000 Series, use the same connection as shown on figure 2.1.
• Two conductors, 18-gauge shielded stranded wires must be used. Ground one end of the shielded to earth
ground. See installation instruction if ASP1 Surge Protector is used.
• Do not share power transformer or power supply between the AeGIS and other electronic equipment.
• Turn the power "ON" (left position). The Power Light Emitting Diode (LED2) should be "ON". You should see
“Welcome to Pach's Telephone Access Systems" on the Liquid Crystal Display (LCD). If the display is blank, turn
the system off and see Chapter 4.0 Operations and Chapter 6.0 Trouble Shooting Guides.
BATTERY BACKUP
The AeGIS 7000 Series have built-in charging circuit for battery backup. The battery will keep the system in full operation
during power failure. Recommended battery is 12 VDC, 4.5 Ahr rechargeable (customer supply). The life of the battery is
approximately 8 hours in idle mode.
• Use two conductors 8-gauge shielded stranded wires.
WARNING: The connection is polarity sensitive. Connect the battery (+) terminal to the connector labeled (BAT) on the
AeGIS and the battery (-) terminal to the connector labeled LCOM on the AeGIS. See figure 2.1 for wiring
diagram.
NIGHT LIGHT
14V 0.080A 15,000 Average life hours light bulbs. Use the same rating of replacement light bulb.
5
Pach and Company Chapter 2 Page 6
AeGIS 7000 Series INSTALLATION 10/01/01
6
7

Chapter 3
PROGRAMMING
The AeGIS 7000 Series can be programmed locally using the built-in keypad or remotely via a touch tone phone.
3.1 LOCAL PROGRAMMING VIA BUILT-IN KEYPAD
Log on to programming mode
Two ways to log on to programming mode:
1) PRESS 0 AND # SIMULTANEOUSLY THEN RELEASE, the display screen stops scrolling (If the display screen is still
scrolling repeat this step again) then enter the valid 4-digit Master Code (default Master Code: 0000). Now, you are in
programming mode, the display shows:
and proceed to Local Programming Table 3.1. If the system idles in 30 seconds, the display will return to a scrolling mode.
2) IF YOU DO NOT HAVE A VALID MASTERCODE, open the panel (key must be used) then press and release the “RED
BUTTON” on the board and the display shows:
x x x x: 4-digit Master Code.
then press #. Now, you are in programming mode and proceed to Local Programming Table 3.1. If the system idles in 30
seconds, the display will return to a scrolling mode.
3.2 REMOTE PROGRAMMING VIA A TOUCH TONE PHONE
You may use Telephone Remote programming to add a tenant, delete or modify the system's parameter. The rules below
must be followed:
• Enable the system Auto Answer (see table 3.1 Function Code 74-Enable or Disable Auto Answer), the AeGIS
7000 Series will answer on the first ring.
• Do not share the AeGIS 7000 phone line with any answering devices such as a fax machine, alarm device or
modem.
• A touch-tone phone must be used.
• Only letter A-Z can be entered using a touch-tone phone for a person name. No punctuation or number can be
entered.
• A person name only in upper case.
Log on to programming mode
1) SINGLE SYSTEM
Step 1 Call the AeGIS 7000. When the system answer you will hear:
One Short Beep: Door is opened.
Two Short Beeps: Door is closed.
Press # key
Step 2 Press your valid Master Code.
• If your Master Code is accepted, you will hear Two Short Beeps and now, you are in the programming
mode and proceed to Touch Tone Programming Table 3.1.
Note: If the system idles in 30 seconds, the display will return to a scrolling mode.
• If your Master Code is rejected, the system will disconnect.
Pach and Company Chapter 3 Page 7
AeGIS 7000 Series PROGRAMMING 10/01/01
Select Func: _ _
Master Code: x x x x

2) MULTI-SYSTEM IN SINGLE TELEPHONE LINE
Step 1 Call into the AeGIS 7000 using a touch tone phone. When the system answer you will hear:
• One Short Beep: Door is opened.
• Two Short Beeps: Door is closed.
• One Long Beep: Combination of Closed and open.
Step 2 Press the System Number you want to log in (1-8) then press # key.
Step 3 Press your valid Master Code.
• If your Master Code is accepted, you will hear Two Short Beeps and you are in the programming mode,
then proceed to Touch Tone Programming Table 3.1.
Note: If the system idles in 30 seconds, the display will return to a scrolling mode.
• If your Master Code is rejected, the system will disconnect.
Step 4 Follow the next programming sections below to program the tenant database and parameters.
TABLE 3.1 PROGRAMMING FUNCTION CODES
*
#
00
REPLACE SYSTEM
MASTER CODE
(Default setting is
0000)
Master Code is used to log
on to programming mode,
not to unlock door or gate.
1. Exit the programming mode by pressing * once or
twice.
2. Clear the programmed name, phone number or access
code by pressing *
3. Press * then the 4-digit access code to unlock the door
or gate via the system keypad.
Press # to accept program.
Step 1 Log on to programming mode (see section 3.1).
The display shows
Step 2 Enter Function code 00, then press #, the display
shows
Step 3 Enter the new 4-digit Master Code then press #
the display shows
If you press * the display shows
Ignore the message, and your existing Master
Code will remain in the system.
Step 4 Select another Function Code to program
different field from the table or press *to exit the
programming mode and you hear “Three
Short Beeps”.
Not applicable.
Press # to accept program.
Step 1 Log on to programming mode,
see section 3.2. If you have
logged on. Proceed to step
2.
Step 2 Enter Function Code 00 and
press #, you will hear “One
Short Beep”.
Step 3 Enter the new Master Code and
press #, and you will hear “Two
Short Beeps”.
Step 4 Select another Function Code to
program another parameter or
press 91 then press # to
disconnect the call, you will hear
“Three Short Beeps”.
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Pach and Company Chapter 3 Page 8
AeGIS 7000 Series PROGRAMMING 10/01/01
Select Func: _ _
Master Code: 0000
Select Func: _ _
ERROR DATA * * * *

01
PROGRAM ANEW
TENANT
There are four different
fields that need to be
programmed: Directory
Code (DIR), Name, Phone
Number (PH #), and
Access Code.
Directory Code (DIR):A
unique (non-duplicating) 2,
3 (factory default) or 4 digit
code assigned for each
tenant for identification
(Used Function Code 06 to
Change Directory Digits). It
links to tenant name,
phone number and access
code. The same number of
digit must be used on
every tenant's directory.
Name: up to 16
characters.
Phone Number: up to
11-digit.
Access Code: A 4-digits
personal code is assigned
to individuals for the
purpose of granting
entry using the Telephone
Entry Systems keypad.
Please note the following
criteria before entering
the tenant Directory
Code, Name, Phone
Number and Access
Code.
1. The Directory Codes
can NOT be duplicated.
2. Each Directory Code is
considered as one
tenant.
3. The existing Directory
Codes cannot be
changed by another
directory code. They
can be deleted using
Function Code "03".
4. Delete the unused
directory code to avoid
running out of memory.
5. The Tenant Directory
database must contain
name. Tenant Directory
cannot be deleted if the
directory code is
forgotten and no name
is programmed.
6. The tenant names may
be entered in any order.
The system will
automatically arrange
them it alphabetical
order.
7. The same Name,
Telephone Number and
Access Code can be
assigned into different
directory code number.
Step 1 Log on to programming mode (see section 3.1),
the display shows
Step 2 Enter Function Code 01 then press #, the
display shows:
Step 3 Enter the directory code (see setting on
function code 06) 2, 3 (default) or 4-digit. The
display shows:
The display goes blank about one second then
the display shows:
Proceed to Step 4.
If the directory code has already used,
the display shows:
Return to Step 2.
If the memory is full, the display shows:
You cannot program more tenant unless if you
delete the existing one or call Pach and
Company to purchase memory upgrade EPROM.
Step 4 Enter the tenant name (up to 16 characters )
using the keypad (see keypad layout) then
• Press # after entering each letter then
• Press # # after entering the last letter
the display shows:
Press 0 for space ( move
cursor to the right).
Press 8 then 0 for back
space ( move cursor to
the left.
Press *to clear all letters
or numbers entered.
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 01 then
press #, you hear “One
Short Beep”.
Step 3 Enter a tenant directory code (2,
3 or 4 digits) then press # and
you hear “One Short Beep”.
If the directory has already
existed, you hear “Two Long
Beeps” , return to step 2.
Step 4 Enter tenant name up to 16
characters then
• Press # after entering each
letter then
• Press # # after entering the last
letter
then you hear “One Short
Beep”.
Step 5 Enter tenant's telephone number
up to 11-digit and press #, you
hear “One Short Beep”.
Step 6 Enter tenant's 4-digits access
code number then press #, you
will “One Short Beep”.
Step 7 Select another Function Code to
program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear “Three Short
Beeps”.
Pach and Company Chapter 3 Page 9
AeGIS 7000 Series PROGRAMMING 10/01/01
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Select Func: _ _
Enter Dir: _ _ _
Enter the NAME:
_
Dir # is used !
ERROR DATA * * * *
PH #:_ _ _ _ _ _ _ _ _ _ _

Pach and Company Chapter 3 Page 10
AeGIS 7000 Series PROGRAMMING 10/01/01
02
MODIFY AN
EXISTINGTENANT
DIRECTORY
You must know the tenant
directory you want to
modify. If you do not know
the tenant directory, see
Function Code78 View
Directory by Name.
For example, to enter Pach & 12
• Press "7" key once to select the letter "P", then press #.
• Press "2" key four times to select letter "a", then press #.
• Press "2" key six times to select letter "c", then press #.
• Press "4" key five times to select letter "h", then press #.
• Press “0” key once for space
• Press any key to get the &
• Press “0” key once for space
• Press "1" key eleven times to select number "1", then press #.
• Press "1" key twelve times to select number "2", then press
##.
Step 5 Enter the tenant phone number or extension
number up to 11-digit then press #, the display
shows:
Note: The AeGIS 7000 Series does not provide a pause to dial.
Step 6 Enter the 4-digit access code then press #. The
4-digit code is for the tenant to to gain access
into the door or gate. See operation to use the
access code.
Step 7 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you hear “Three Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 02 then press #, the
display shows:
Step 3 Enter the tenant directory to be modified then
press # the display shows:
then
Step 4 • To change name: press * to erase and
program a new one.
• Press # after entering each letter then
• Press # # after entering the last letter
• To keep name: press #.
The display shows:
NOT AVAILABLE.
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
ACCESS CODE:_ _ _ _
Select Func: _ _
Modify Dir:_ _ _
Enter the NAME:
Tenant’s name appear
PH#: Tenant’s Phone

Pach and Company Chapter 3 Page 11
AeGIS 7000 Series PROGRAMMING 10/01/01
03
DELETE AN
EXISTINGTENANT
DIRECTORY
Delete an existing tenant
one by one. This function
code is very useful to free
the system memory by
deleting the unused
directory.
04
CLEAR ALL
TENANTS
DIRECTORY
Step 5 • To change phone number: press * to erase
and program a new one then press #.
• To keep the phone number: press #.
The display shows:
Xis existing access code.
• To change access number: enter a new one
then press #.
• To keep the access code: press #.
Step 6 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will “Three Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 03 then press #, the
display shows:
Step 3 Enter a tenant directory code you want to delete
the press #. The display shows:
If the directory does not exist, the display shows:
Proceed to step 2.
Step 4 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will hear “Three Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 04 then press #, the
display shows:
Step 3 • Press 13 then # the display shows:
then proceed to step 4 or
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 03 then
press #, you hear “One Short
Beep”.
Step 3 Enter the tenant directory code
(2, 3 or 4 digits) you want to
delete then press # and you hear
“Two Short Beeps” means
directory is deleted or “One Long
Beep” then “Two Short Beeps”
means vice versa.
Step 4 Select another Function Code to
program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear “Three Short
Beeps”.
NOT AVAILABLE.
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Access Code: XXXX
Select Func: _ _
Delete Dir: _ _ _
(Dir Code)is deleted !
Error on Delete !
Select Func: _ _
Delete all?13
Are you sure ? 5

05
MANUALLOCK
(OPEN) OR
UNLOCK (CLOSE)
DOOR
06
SELECTING
DIRECTORY DIGITS
Factory default setting is
3-digit.
•Press * to cancel deletion and you hear “One
Long Beep” and proceed to step 5.
Step 4 Press 5 then # to delete or
Press *to cancel deletion.
Step 5 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will hear “Three Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 05 then press #, the
display shows:
Step 3 Enter • 01-98 hours to unlock door or
• 99 hours to to unlock door for
indefinite time or
• 00 hours to lock door
then press # or press *to cancel.
Step 5 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will hear “Three Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 06 then press #, the
display shows:
Step 3 Enter the Directory Digits 2, 3 or 4 then press #
or press *to keep the existing one.
Step 4 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will hear “Three Short Beeps”.
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 05 then
press #, you hear “One Short
Beep”.
Step 3 Enter • 01-98 hours to unlock
door or
• 99 hours to to unlock
door for indefinite time
or
• 00 hours to lock door
then press # you will hear “Two
Long Beeps” and “Two Short
Beeps”.
Step 4 Select another Function Code to
program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear “Three Short
Beeps”.
NOT AVAILABLE.
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Pach and Company Chapter 3 Page 12
AeGIS 7000 Series PROGRAMMING 10/01/01
Select Func: _ _
OPEN: 00 HOURS
Select Func: _ _
DIR DIGITS: 3 _

07
SINGLEOR MULTI
SYSTEMS
(Default setting is
Single)
You must set the system to
multi if more than one
systems are installed using
a single phone line. You
can connect up to eight
system on a single phone
line.
It is not necessary to set
the system to multi if sepa-
rate phone is used for
each system.
If system is set for multi,
Function Code 75 (Key
Press Beep) is disabled.
08
SYSTEM NUMBER
(Default Setting is
1)
It is not necessary to set
the system number if :
1. Remote touch-tone
programming is not
used.
2. Separate phone line is
used for each system.
10
CHANGETHE
WELCOME
SCREEN
Welcome screen is divided
into three segments. Each
segment consists of 16
characters. The welcome
screen can be a
combination of letter and
number.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 07 then press #, the
display shows:
Step 3 Enter • 1 for Single system or
• 0 for multi systems
then press # or press *to keep the existing one.
Step 4 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will hear “Three Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 08 then press #, the
display shows:
Step 3 Enter the system number 1-8 then press # or
press *to keep the existing one.
Step 4 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will hear “Three Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 10 then press #, the
display shows:
Step 3 Press *to erase the 1st segment then enter the
welcome message then press # # to proceed to
the 2nd segment, the display shows:
NOT AVAILABLE.
NOT AVAILABLE.
NOT AVAILABLE.
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Pach and Company Chapter 3 Page 13
AeGIS 7000 Series PROGRAMMING 10/01/01
Select Func: _ _
SING=1, MULT=0: 1
Select Func: _ _
SYSTEM # [1-8] 1
Select Func: _ _
Welcome to Pach’
1st segment
s Telephone Acce

46
SYSTEM
INFORMATION
Display the model number
and the firmware released
date.
50
CLEAR THE
MEMORY TO
FACTORY
DEFAULT
Use this Function Code will
erase the whole database
and and reset the system
to factory default.
Step 4 Press *to erase the 2nd segment then enter
the welcome message then press # # to proceed
to the 3rd segment, the display shows:
Step 5 Press *to erase the 3rd segment then enter
the welcome message then press # #.
Step 6 Proceed to step 2 and select the same Function
Code or different Function Code to continue
programming or press *to exit the programming
mode and you will hear “Three Short Beeps”.
Note: See keypad correlation on page 3.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 46 then press #, the
display shows:
XXX: the model number.
MM/DD/YY: month, date, and year firmware
released.
Step3 Press * then proceed to step 2 and select the
same Function Code or different Function Code
to continue programming or press *to exit the
programming mode and you will hear “Three
Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 50 then press #, the
display shows:
Step 3 Press 1 to confirm the display shows:
and the system returns to Welcome Screen,
or *to cancel and proceed to step 3.
Step4 Press * then proceed to step 2 and select the
same Function Code or different Function Code
NOT AVAILABLE.
NOT AVAILABLE.
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Pach and Company Chapter 3 Page 14
AeGIS 7000 Series PROGRAMMING 09/01/01
ss System . . . * *
Select Func: _ _
V7XXX MM/DD/YY
Select Func: _ _
1 to confirm:_
DB Init. Wait . . ._

70
CHANGE TALK
TIME
(Default setting is
60
seconds)
The talk time is the length
of time the visitor can talk
to the tenant. The talk time
timer starts as soon as the
system initiates the call.
71
CHANGEDOOR
OPENINTERVAL
(Default setting is
12 seconds)
The Door Open Interval is
the length of time the
relay turns on.
72
CHANGELOCK
OUT COUNT
(Default setting is
3)
The system is disabled if
invalid access code has
been entered according to
the lock out count sets on
Function Code 72. The
system will ignore further
access code entries for 90
seconds.
to continue programming or press *to exit the
programming mode and you will hear “Three
Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 70 then press #, the
display shows:
Step 3 Enter Talk Time Value in 3-digit mode (010 -
180) seconds the press #.
Step4 Press * then proceed to step 2 and select the
same Function Code or different Function Code
to continue programming or press *to exit the
programming mode and you will hear “Three
Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 71 then press #, the
display shows:
Step 3 Enter the Open Time value in 2-digit mode (04-
99) seconds then press #.
Step4 Press * then proceed to step 2 and select the
same Function Code or different Function Code
to continue programming or press *to exit the
programming mode and you will hear “Three
Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 72 then press #, the
display shows:
Step 3 Enter the lock out count in one-digit mode (1-9).
Step4 Press * then proceed to step 2 and select the
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 70 then
press #, you hear “One Short
Beep”.
Step 3 Enter the talk time in 3-digit mode
(10-180 seconds) and press #
and you will hear“ Two Short
Beeps”.
Step 4 Select another Function Code to
program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear “Three Short
Beeps”.
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 71 then
press #, you hear “One Short
Beep”.
Step 3 Enter the Open Time value in 2-
digit mode (04-99) seconds then
press # and you will hear “ Two
Short Beeps”.
Step 4 Select another Function Code to
program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear “Three Short
Beeps”.
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 72 then
press #, you hear “One Short
Beep”.
Step 3 Enter the Lock Out Count value in
one-digit (04-99) seconds then
press # and you will hear “ Two
Short Beeps”.
Step 4 Select another Function Code to
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Pach and Company Chapter 3 Page 15
AeGIS 7000 Series PROGRAMMING 09/01/01
Select Func: _ _
TALK TIME:060
Select Func: _ _
OPENTIME: 12
Select Func: _ _
LOCK-OUT CNT: 3

73
SELECT TONE OR
PULSE DIALING
(Default setting is
tone)
If set to Tone: pulse phone
can’t unlock the door by
pressing 9.
If set to pulse: both tone
and pulse phone can
unlock the door by
pressing 9.
74
ENABLE OR
DISABLE AUTO
ANSWER
(Default setting is
Enable)
If Enable, the system will
answer an incoming call.
If disable, the system will
not answer an incoming
call.
This feature is useful if:
• Remote touch-tone
programming is used or
• For the tenant to call
the system in case the
tenant is not available at
the time the visitor call.
75
TURN ON OR OFF
KEY PRESS BEEP
(Default setting is
ON)
If ON, the system beep if
key is pressed.
If OFF, the system does
not beep if the key is
pressed.
If the system is set for
Multi (see Function Code
07),
same Function Code or different Function Code
to continue programming or press *to exit the
programming mode and you will hear “Three
Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 73 then press #, the
display shows:
Step 3 Enter 1 for Tone or 0 for Pulse then press #.
Step4 Press * then proceed to step 2 and select the
same Function Code or different Function Code
to continue programming or press *to exit the
programming mode and you will hear “Three
Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 74 then press #, the
display shows:
Step 3 Enter 1 to Enable or 0 to Disable, then press #.
Step4 Press * then proceed to step 2 and select the
same Function Code or different Function Code
to continue programming or press *to exit the
programming mode and you will hear “Three
Short Beeps”.
Step 1 Log on to programming mode (see section 3.1),
the display shows:
Step 2 Enter Function Code 75 then press #, the
display shows:
Step 3 Enter 1 to turn ON key press beep or 0
turn OFF key press beep, then press #.
program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear “Three Short
Beeps”.
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 73 then
press #, you hear “One Short
Beep”.
Step 3 Enter 1 for Tone or 0 for Pulse
then press #, then press # and
you will hear “ Two Short
Beeps”.
Step 4 Select another Function Code
to program another parameter or
tenant's directory, otherwise enter
91 then press # to disconnect the
call, you hear “Three Short
Beeps”.
NOT AVAILABLE.
Step 1 Log on to programming mode,
see section 3.2 If you have
logged on proceed to step 2.
Step 2 Enter Function Code 75 then
press #, you hear “One Short
Beep”.
Step 3 Enter 1 to turn ON key press
beepor 0 to turn OFF key press
beepthen press #, then
press #and you will hear “Two
Short Beeps”.
FUNCTION CODE LOCALPROGRAMMING TOUCH TONE PROGRAMMING
Pach and Company Chapter 3 Page 16
AeGIS 7000 Series PROGRAMMING 09/01/01
Select Func: _ _
TONE=1 PULSE=0: 1
Select Func: _ _
Auto Answer=1 : 1
Select Func: _ _
BEEP On=1 OFF=0: 1