Pacific energy NEO 1.6 INSERT User manual

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
1
1
NEO 1.6 & NEO 2.5
ZERO CLEARANCE MANUAL
Distributed by
Pivot Stove & Heating Co
1300 474 686
pivotstove.com.au

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
2
CONTENTS
•1 x base plate
•2 x side panels – inner
•2 x side panels – outer
•2 x top plates
•2 x flue locating
•77 x Self-tapping screws
Pacific Energy Zero Box Over View
The Pacific Energy Zero Box has been tested to AS/NZS 2918:2001 and must be installed in
accordance to the manufactures specifications
No modifications to the box or the installation specifications are authorized
What is a Zero Clearance Box?
The Pacific Energy Zero Box has been designed to allow the Neo 1.6 & the NEO 2.5 Inbuilt wood
heaters to be installed into a framed out wall cavity
This manual will explain the following
-How to assemble the Zero Clearance Box
-Framing and installation Specifications
Assembling the Zero Clearance Box
A brief description is the Zero Clearance Box is a box within a box
The Zero Clearance box is made up in 3 sections
-Assembly of the outer Box
-Assembly of the inner Box
-Completing the Zero Clearance Box

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
3
Assembling the outer box
Step 1
Place the base plate on the floor
The 3 up-turn sides are to be facing up
-the side with the 5 feet to be facing down
-the side with the 3 feet to be facing up
The front of the Base Plate has no upturn edge
3 Feet facing up

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
4
Stage 2
Fit the Right and side and the Left side to the base plate with fixing screws
The Sides are to be located on the inside of the base plate
- Note – air holes are to be on the bottom
Front Angle return to be facing outwards Rear Angle returns to be facing inwards
Stage 3
Fit the rear panel to the base plate and side panels with fixing screws
-Note – the air holes are to be on the bottom
This completes the pre- assembly of the Outer Box.

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
5
Assembling the inner box
Stage 4
Assemble the 2 x inner sides to the rear side with fixing screws
-
the air holes are to be facing the bottom
o
the bottom lip is to be facing out

the front return is to be facing out

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
6
Stage 5
Assemble the top panel to the Sides and Rear with fixing screws
Stage 6
Fix the solid spigot to the top of the top of the inner box with fixing screws

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
7
NOTE: When installing the Neo 1.6
The Spigot goes towards the front of the Zero Clearance Box
NOTE: When installing the Neo 2.5
The Spigot goes towards the back of the Zero Clearance Box

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
8
Completing the Zero Clearance Box
Stage 7
Slide the inner box into the outer box
Stage 8
Assemble the top to the outer box with fixing screws

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
9
Stage 9
Fix the crimped spigot on top of the top of the Zero Clearance Box with fixing screws
NOTE
We recommend you paint the bottom lip of the Zero Clearance Box with Stove Bright Metallic Black
when raising the Neo Wood Heaters units off the floor so you don’t see the metal Zero Clearance Kit

Distributed by Pivot Stove & Heating 1300 474 686 pivotstove.com.au
10
Framing Guide
Framing Guide
Cavity Height 1,020 mm
Cavity Width 1,080 mm
Cavity Depth 620 mm
If raising of the floor, recommended height off the floor 300mm
Height
Depth
Width
Floor Protection
18mm thick fireproof Board
- Needs to extend under the Zero Clearance Box
- Hearth to extend 500mm in front of the heater
Recommended size of Bellis Board
1,075mm deep x 900mm wide
Finished Surface
Extending 300mm above the heater,
a non-combustible material is to be used
Power
Inside the frame out,
a 240V power point to an
External isolation switch is required
Flue
A min of 3.6Mtr triple Skin Flue Kit - installed to
AS 2918:2001