Pacific energy TOFINO i20 User manual

WARNING: If the information in these
instructions is not followed exactly a fire
or explosion may result causing property
damage, personal injury or death.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Thisappliancemaybeinstalledinan aftermarket
permanently located, manufacturedhome (USA
only) or mobile home, where not prohibited by
local codes.
This appliance is only for use with the type of
gas indicated on the rating plate. This appliance
is not convertible for use with other gases
unless a certified kit is used.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapours and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical Switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier call the
fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
TOFINO
TOFINO OPERATING
INSTRUCTIONS
MODEL: TOFINO i20
(SIT & Maxitrol versions)
SERIES: A
DIRECT VENT GAS INSERT
Visit www.pacificenergy.net for the most recent version of this manual
OPERATING INSTRUCTIONS
5055.980-A
150317-32

Caution ...................................................................................... 3
Safety ........................................................................................ 4
WHAT TO DO IF YOU SMELL GAS ................................... 4
First Fire ..................................................................................... 5
Warnings and Cautions ............................................................. 5
Remote Control Operation (SIT Proame) ................................. 6
System Description .......................................................... 6
Transmitter (Remote Control with LCD Display) ............... 6
IFC Module .........................................................................7
Operating Procedure ..........................................................7
Initializing the system for the rst time ...............................7
Temperature indication Display .......................................... 9
Turn on the Fireplace.......................................................... 9
Turn off the Fireplace ......................................................... 9
Manual Bypass of the Remote System.............................. 9
Key Lock ............................................................................ 9
Room Thermostat (Transmitter Operation) ..................... 9
Remote Flame Control .................................................... 10
Split Flow Function .......................................................... 10
Smart Thermostat (Transmitter Operation) ......................11
Comfort Fan Speed Control..............................................11
Low Battery Power Detection .......................................... 12
Transmitter ....................................................................... 12
Receiver ........................................................................... 12
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection .... 12
Remote Control Operation (Maxitrol) ....................................... 13
Operating Instructions...................................................... 13
Setting the Electronic Code ............................................. 14
Setting Fahrenheit or Celsius........................................... 15
Setting the Time............................................................... 15
Child Proof ....................................................................... 15
Manual mode (handset) ................................................... 15
Handset One-Button Operation....................................... 16
Handset Two-Button Operation ....................................... 16
Standby Mode (Pilot Flame)............................................. 16
To Turn Off Fire ................................................................. 16
Flame Height Adjustment..................................................17
Designated Low Fire and High Fire...................................17
Countdown Timer ............................................................ 18
Modes of Operation ......................................................... 18
Thermostatic Mode .......................................................... 19
Program Mode ................................................................. 19
To turn on appliance......................................................... 22
To Turn Off Gas Appliance................................................ 23
Automatic Turn Down....................................................... 23
Automatic Shut Off........................................................... 23
On-Demand Pilot ............................................................. 23
Receiver ........................................................................... 24
Lighting Instructions ................................................................ 25
Maintenance ............................................................................ 26
Glass Door: ...................................................................... 26
Periodically:...................................................................... 26
Surround Installation/Removal Instructions .............................27
Removal ............................................................................27
Installation.........................................................................27
Door Installation/Removal ........................................................ 28
Removal ........................................................................... 28
Installation........................................................................ 28
i20 TOFINO
Table Of Contents
2150317-32
5055.980-A

i20 TOFINO
This replace is equipped with a micro mesh safety screen for your protection and
must be installed with the unit. Removal of the safety screen will cause the replace
to become a burn hazard.
Caution
FOR YOUR SAFETY - Do not install or operate your Pacic Energy replace without rst reading
and understanding this manual. Any installation or operational deviation from the following instruc-
tions voids the Pacic Energy Fireplace Warranty and may prove hazardous.
This appliance and its individual shut off valve must be disconnected from gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
This appliance must be isolated from the gas supply piping system by closing its individual manual
shut off valve during any pressure testing of the gas supply piping system at test pressures equal to
or less than 1/2 psig (3.5 kPa).
Note: When lit for the rst time, the appliance will emit a slight odour for a couple of hours. This
is due to the curing of paints, sealants and lubricants used in the manufacturing process. This
condition is temporary. Open doors and windows to ventilate area. Smoke and fumes caused by the
curing process may cause discomfort to some individuals.
Do not use the replace if any part has been under water. Immediately call a qualied service
technician to inspect the replace and to replace any part of the control system and any gas control
which has been under water.
35055.980-A
150317-32

i20 TOFINO
Safety
• Due to high temperatures, this gas appliance should be located out of trafc and away from
furniture and draperies.
• Children and adults should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical
barrier is recommended if there are at risk individuals in the house. To restrict access to a
replace or stove, install an adjustable safety gate to keep toddlers, young children and other at
risk individuals out of the room and away from hot surfaces.
• Clothing or other ammable material should not be placed on or near the appliance.
• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the
Surround Kit component and shall be installed.
• If the barrier becomes damaged, the barrier shall be replaced with the manufacturers barrier
for this appliance.
• Any grill, panel or door removed for servicing the unit must be replaced prior to operating.
• Installation and repair should be done by a qualied service person. The appliance should be
inspected before use and at least annually by a professional service person. More frequent
cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burners and circulating air passageways of the appliance
be kept clean.
• This appliance must not be connected to a chimney ue serving a separate solid fuel burning
appliance.
• It is our policy that no responsibility is assumed by the Company or by any of its employees or
representatives for any damages caused by an inoperable, inadequate, or unsafe condition which
is the result, either directly or indirectly, of any improper operation or installation procedures.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical Switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier call the re department.
• Installation and service must be performed by a qualied installer, service agency or the gas
supplier.
4150317-32
5055.980-A

NOTE: Fireplace may take up to
30 seconds to ignite each time the
“ON” button has been selected
First Fire
Congratulations on your purchase of a Pacific Energy Gas Appliance.
Your replace has been professionally installed by:
Dealer name: ___________________________________________________
Phone Number:___________________________________________________
If you discover any problems with your gas appliance contact your dealer immediately to have the
unit repaired.
Caution: Do not attempt to repair the replace because you may cause injury to yourself or others,
and risk causing damage to the unit.
Before operating your appliance carefully read this manual and pay close attention to all Safety
Warnings.
The manual contains important information on the unit’s safe operation and maintenance.
When lit for the rst time, the replace will emit a slight odour for a couple of hours. This is due to
the curing of paints, sealants and lubricants used in the manufacturing process. This condition is
temporary. Open doors and windows to ventilate area. Odour caused by the curing process may
cause discomfort to some individuals.
It is normal for replaces fabricated of steel to give off some expansion and/or contraction noises
during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or
cook stove oven.
Warnings and Cautions
WARNING
Fire Hazard. Can cause severe injury or death
The Receiver causes ignition of the appliance. The appliance can turn on suddenly. Keep away from the
appliance burner when operating the remote system or activating manual bypass of the remote system.
WARNING
Shock Hazard. Can cause severe injury or death
This device is powered by line voltage. Do not try to repair this device. In no way is the enclosure to be
tampered with or opened. Disconnect from line voltage before performing any maintenance.
i20 TOFINO 55055.980-A
150317-32

Remote Control Operation (SIT Proflame)
System Description
The Proame 2 Remote Control System consists of two elements:
1. Proame 2 Remote Control Transmitter.
2. Proame Integrated Fireplace Control (IFC) (Figure 3) board and a wiring harness to connect the IFC to
the gas valve and stepper motor.
Transmitter (Remote Control with LCD Display)
The Proame 2 Transmitter uses a streamline design with a simple button layout and informative LCD
display (Figure 1). The transmitter is powered by 3 AAA type batteries. A Mode key is provided to Index
between the features and a Thermostat key is used to turn on/off or index through thermostat functions
(Figure 1 and Figure 2).
Blue back lit LCD display
ON/OFF Key
THERMOSTAT Key
UP/DOWN Arrow Key
MODE Key
Figure 1: Proame 2 handset.
OFF
ON
SMART
MAX MAX
KEY LOCK
LOW BATTERY ALARM
ROOM
TEMPERATURE
CPI MODE
DIMMER ON
FLAME LEVEL
SET POINT:
TEMPERATURE/LEVEL/STATE
THERMOSTAT OFF/
ON/SMART
TRANSMISSION
COMFORT FAN
SPLIT FLOW
Figure 2: Proame 2 LCD display.
i20 TOFINO
6150317-32
5055.980-A

IFC Module
The Proame 2 Integrated Fireplace Control (IFC) module (Figure 3) is a device that allows automatic ignition
and pilot ame supervision, and commands the functions of the hearth Heater. It’s congured to control the
ON/OFF main burner operation, giving the choice of both IPI (intermittent pilot ignition), and CPI (continuous
pilot ignition) modes. The Proame 2 IFC module controls and connects directly to the pilot assembly and the
automatic valve using low electric power.
The IFC module can be powered by both an AC power supply, and battery pack for back up. The Proame
2 offers the added ability to control the comfort fan speed from OFF through six (6) speeds, a remotely
actuated auxiliary outlet and a dimmable light outlet. The external batteries can provide DC power to the IFC
allowing the batteries to be used only when line power is interrupted or lost, and if the Heater does not use a
combustion fan.
Operating Procedure
Initializing the system for the rst time.
1. Install 4 AA batteries into the battery holder located behind the electronic control module on the pull - out
caddy.
2. Install 3 AAA batteries into the Proame 2 Remote Transmitter (Figure 1).
3. Plug the power cord into the Tono and open the gas supply line.
4. With the front surround (Figure 47 on page 28) and backing plate (Figure 48 on page 28) removed,
press the button marked “PRG” on the caddy (Figure 3) once. The module will beep 3 times indicating
that it is ready to synchronize with a remote transmitter.
5. On the remote transmitter, push the power on button once. The remote transmitter will beep 4 times to
indicate that the remote transmitter and the control module are now synchronized. The remote transmitter
is now ready to use.
i20 TOFINO 75055.980-A
150317-32

Figure 3: SIT electronic controller (IFC)
mounted onto caddy.
PRG
Figure 4: Program button.
ON
REMOTE
OFF
Figure 5: On Off switch for SIT units.
i20 TOFINO
8150317-32
5055.980-A

Figure 6: Temperature in
celcius.
Figure 7: Temperature in
fahrenheit.
Figure 8: Key lock icon.
Figure 5: On Off switch for SIT units.
i20 TOFINO
Temperature indication Display
With the system in the “OFF” position, press the Thermostat Key and the
Mode Key at the same time. Look at the LCD screen on the transmitter to
verify that a C or F is visible to the right of the Room Temperature display
(Figure 6 and Figure 7).
Turn on the Fireplace
With the system OFF, press the ON/OFF Key on the remote transmitter. The
remote transmitter display will show some other active Icons on the screen.
At the same time the Receiver will activate the Heater. A single “beep” from
the Receiver (module) will conrm reception of the command.
Turn off the Fireplace
With the system ON, press the ON/OFF Key on the Remote transmitter.
The Remote transmitter LCD display will only show the room temperature
(Figure 6 and Figure 7). At the same time the Receiver (module) will turn off
the Heater. A single “beep” from the Receiver conrms reception of the
command.
Manual Bypass of the Remote System
If the batteries of the receiver or remote transmitter are low or depleted, the
Heater can be turned off manually using ON/OFF switch located on the
left hand side of the backing plate (Figure 5). This will bypass the remote
transmitter.
Key Lock
This function will lock the keys to avoid unsupervised operation. To activate
this function, press the MODE and UP keys at the same time. The lock icon
will appear (Figure 8). To de-activate this function, press the MODE and UP
keys at the same time.
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room thermostat. The thermostat
can be set to a desired temperature to control the comfort level in a room.
To activate this function, press the Thermostat key (Figure 1). The LCD
display on the transmitter will change to show that the room thermostat
is “ON” and the set temperature is now displayed (Figure 9). To adjust
the set point, press the up or down arrow keys until the desired set point
temperature is displayed on the LCD screen of the transmitter.
Room Temperature
Set Temperature
Figure 9: Room temperature control.
95055.980-A
150317-32

i20 TOFINO
Remote Flame Control
The Proame has six (6) ame levels. With the
system on, and the ame level at the maximum in
the appliance, pressing the down arrow key once will
reduce the ame height by one step until the ame is
turned off.
The Up Arrow Key will increase the ame height each
time it is pressed. If the Up Arrow Key is pressed
while the system is on but the ame is off, the ame
will come on in the high position (Figure 10). A single
“beep” will conrm reception of the command.
Flame Off
Flame level 5
Flame level Max
Flame level 1
Figure 10: Flame level control.
Split Flow Function
The secondary burner is controlled by the split ow.
To activate this function, use the Mode Key (Figure
1) to index to the SPLIT FLOW icon (Figure 11 and
Figure 12). Pressing the Up Arrow Key will activate
the secondary burner. Pressing the Down Arrow
Key will turn the secondary burner off. A single
“beep” will conrm the reception of the command.
Figure 11: Split ow Off. Figure 12: Split ow ON.
10 150317-32
5055.980-A

i20 TOFINO
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the ame height in accordance to the difference between the set point
and the room temperatures. As the room temperature gets closer to the set point, the Smart Function will
modulate the ame down. If the room temperature is cool, the Smart Function will modulate the ame up. To
activate this function, press the THERMOSTAT key (Figure 1) until the word “SMART” appears to the right of
the temperature icon (Figure 13). To adjust the set point, press the up or down arrow keys until the desired set
point temperature is displayed on the LCD screen of the remote transmitter (Figure 14).
Comfort Fan Speed Control
The SIT version heater is equipped with a hot air circulating fan. The speed of the fan can be controlled by the
Proame 2 System. The fan speed can be adjusted through six (6) speeds. To activate this function use the
Mode Key (Figure 1) to index to the fan control icon (Figure 15). Use the Up/Down Arrow Keys to turn on, off
or adjust the fan speed (Figure 16). A single “beep” will conrm reception of the command.
Figure 13: Smart ame
control.
Figure 14: Smart ame
function set low.
Figure 15: Comfort fan HI. Figure 16: Comfort fan off.
11 5055.980-A
150317-32

Low Battery Power Detection
Transmitter
The life span of the remote control batteries depends on various factors: quality of the batteries used, the
number of ignitions of the Heater, the number of changes to the room thermostat set point, etc.
When the remote batteries are low, an icon will appear on the LCD display of the remote (Figure 19) before all
battery power is lost. When the batteries are replaced this icon will disappear.
The life span of the IFC module batteries depends on various factors: quality of the batteries used, the
number of ignitions of the Heater, the number of changes to the room thermostat set point, etc.
When the IFC batteries are low, a “double-beep” will be emitted from the IFC module when it receives a
command from the remote. This is an alert for a low battery condition for the IFC board. When the batteries
are replaced, a single “beep” will be emitted from the IFC module when a key is pressed. See “Initializing the
system for the rst time.” on page 7.
Receiver
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
With the system in the “OFF” position, press the Mode Key (Figure 1) to index to the CPI mode icon
(Figure 18). Pressing the Up Arrow Key will activate the Continuous Pilot Ignition mode (CPI). Pressing the
Down Arrow Key will return to IPI. A single “beep” will conrm the reception of the command.
Figure 17: IPI Mode. Figure 18: CPI Mode.
Figure 19: Low battery.
i20 TOFINO
12 150317-32
5055.980-A

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
Remote Control Operation (Maxitrol)
Operating Instructions
General Notes:
Notice: Wiring of valve and receiver must be completed before starting ignition. Failure to do so could
damage the electronics.
Batteries - Handset
• Low battery indicator on handsets.
Batteries - Receiver
• Low battery indication: frequent beeps for 3 seconds when motor turns.
Program Mode
Temperature
Time
Countdown Timer
Signal IndicatorChild Proof
Thermostatic Mode
ON
AM
PM
OFF
Battery Status
Fahrenheit
or Celsius
Figure 20: Maxitrol 6 symbol display.
i20 TOFINO 13 5055.980-A
150317-32

Software Version
Press and buttons simultaneously. Software version is displayed.
Handset Model Number
Press and buttons simultaneously. Handset model number is displayed.
Deactivated Functions
1. Install batteries. All icons are displayed and ashing.
2. While the icons are ashing, press the relevant function button and hold for 10 seconds.
3. The function icon will ash until deactivation is complete. Deactivation is complete when function icon and two hori-
zontal bars are displayed.
NOTE: If a deactivated button is pressed, there is no function, and two horizontal bars are displayed.
NOTE: Deactivation remains in effect after change of batteries.
Activate Functions
1. Install batteries. All icons are displayed and ashing.
2. To activate a function, press the relevant button and hold for 10 seconds.
3. The function icon will continue to ash until activation is complete. Activation is complete when the
function icon is displayed.
The following Functions can be Deactivated / Activated:
• CHILD PROOF
• PROGRAM MODE
• THERMOSTATIC MODE (also deactivates PROGRAM MODE)
• ECO MODE
Setting the Electronic Code
(First time use only)
Radio Frequency Handset
A code is selected automatically for all Mertik Maxitrol electronics from among 65000 codes available. The
receiver must be paired with the handset. (see instructions on page 25).
WARNING
• Battery replacement is recommended at the beginning of each heating season.
• Old or dead batteries should be removed immediately. If left in the unit the batteries can overheat,
leak, and / or explode.
• Do NOT expose batteries (including during storage) to direct sunlight, excessive heat, re, mois-
ture, or severe impact. Each of these conditions can cause the batteries to overheat, leak, and/or
explode.
• New and old batteries and different brands of batteries should not be used together. Mixing of
various batteries can cause the batteries to overheat, leak, and/or explode.
i20 TOFINO
14 150317-32
5055.980-A

Setting Fahrenheit or Celsius
Child Proof
Setting the Time
Manual mode (handset)
To change between °C and °F, press and buttons simultaneously.
NOTE: Choosing °F results in a 12 hour clock. Choosing °C results in a 24 hour clock.
1. Press and buttons simultaneously. Day ashes.
2. Press or button to select a number to correspond with the day of the week
(e.g. = Monday, = Tuesday, = Wednesday, = Thursday, = Friday, = Saturday,
= Sunday.
3. Press and buttons simultaneously. Hour ashes.
4. To select hour, press or button.
5. Press and buttons simultaneously. Minutes ash.
6. To select minutes, press or button.
7. To conrm, press and buttons simultaneously or wait.
ON:
To activate, press and buttons simultaneously. is displayed and the handset
is rendered inoperable, except for the off function.
OFF:
To deactivate, press and buttons simultaneously. disappears.
NOTICE
BEFORE OPERATING
Make sure MANUAL knob on the GV60 valve is in the ON, full position.
Place the ON/OFF switch in the I (ON) position.
When pilot ignition is conrmed, motor turns automatically to maximum ame height.
TO TURN ON FIRE
AM
PM
Figure 21: Setting F or C.
ON
AM
PM
OFF
Figure 22: Setting the time.
ON
AM
PM
OFF
Figure 23: Child proof.
i20 TOFINO 15 5055.980-A
150317-32

Handset One-Button Operation
Handset Two-Button Operation
(Default Setting)
• Press until two short beeps and a blinking series of lines conrms the start
sequence has begun; release button.
• Main gas ows once pilot ignition is conrmed.
• Handset automatically goes into Manual Mode after main burner ignition.
NOTICE
Change from one-button to two-button ignition operation by pressing and holding
button for 10 seconds immediately after installing batteries. ON is displayed and
1 is ashing. When change is complete, 1 will change to 2.
(Default Setting)
• Press and button simultaneously until two short beeps and a blinking series of
lines conrms the start sequence has begun; release button.
• Main gas ows once pilot ignition is conrmed.
• Handset automatically goes into Manual Mode after main burner ignition.
NOTICE
Change from two-button to one-button ignition operation by pressing and holding
button for 10 seconds immediately after installing batteries. ON is displayed and
2 is ashing. When change is complete, 2 will change to 1.
If the pilot does not stay lit after several tries, turn the main valve knob to OFF and follow the instructions “To
Turn Off Gas Appliance.” on page 24.
Standby Mode (Pilot Flame)
Handset
• Press and hold button to set appliance to pilot ame.
To Turn Off Fire
Handset
• Press button to turn off.
NOTE: There will be a 30 second delay before the unit can turn on again.
ON
AM
PM
OFF
Figure 24: Handset one
button operation.
ON
AM
PM
OFF
Figure 25: Handset two
button
operation.
ON
AM
PM
OFF
Figure 26: To turn off re.
i20 TOFINO
16 150317-32
5055.980-A

Flame Height Adjustment
Designated Low Fire and High Fire
NOTE: Back-light must be on for high re and low re double - click operation.
Handset
• To increase ame height, press and hold button.
• To decrease ame height or to set appliance to pilot ame, press and hold
button.
• To go to low re, double-click button. is displayed.
NOTE: Flame goes to high re rst before going to low re.
• To go to high re, double-click button.
is displayed.
If the appliance will not operate, follow the instructions “To Turn Off Gas Appliance.” on page 24.
ON
AM
PM
OFF
Figure 27: Flame height
adjustment.
AM
Figure 28: Low.
AM
Figure 29: Hi.
i20 TOFINO 17 5055.980-A
150317-32

Countdown Timer
NOTE: At end of countdown time period, the re turns off. The Countdown Timer only works in Manual,
Thermostatic, and Eco Modes. Maximum countdown time is 9 hours and 50 minutes.
Modes of Operation
ON/SETTING:
1. Press and hold button until displayed and hour ashes.
2. To select hour, press or button.
3. To conrm, press button. Minutes ash.
4. To select minutes, press or button.
5. To conrm, press or wait.
OFF:
Press button, and countdown time disappears.
Thermostatic Mode
The room temperature is measured and compared to the set temperature. The ame
height is then automatically adjusted to achieve the set temperature.
Program Mode
Programs 1 and 2, each can be programmed to go on and off at specic times at a
set temperature.
ON
AM
OFF
Figure 30: Countdown
timer.
ON
AM
PM
OFF
Figure 31: Thermostatic
mode.
ON
AM
PM
OFF
Figure 32: Program
mode 2.
i20 TOFINO
18 150317-32
5055.980-A

Thermostatic Mode
ON:
Press . displayed, preset temperature displayed briey, and then room
temperature displayed.
OFF:
1. Press button.
2. Press or button to enter Manual Mode.
3. Press button to enter Program mode.
SETTING:
1. Press button and hold until displayed, temperature ashes.
2. To adjust set temperature, press or button.
3. To conrm, press button or wait.
Program Mode
ON:
Press button. , 1 or 2, ON or OFF displayed.
OFF:
1. Press or or button to enter Manual Mode.
2. Press button to enter Thermostatic Mode.
NOTE: The set temperature for Thermostatic Mode is the temperature for the on time
in Program Mode. Changing the thermostatic Mode set temperature also
changes the on time temperature in Program Mode.
Default settings:
ON TIME (Thermostatic) TEMPERATURE: 21°C (70 °F)
OFF TIME TEMPERATURE: “ ” (pilot ame only)
ON
AM
PM
OFF
Figure 33: Thermostatic
mode.
ON
AM
PM
OFF
Figure 34: Setting (Thermostatic mode).
ON
AM
PM
OFF
Figure 35: Program mode on.
AM
PM
Figure 36: Program
mode off.
i20 TOFINO 19 5055.980-A
150317-32

TEMPERATURE SETTING:
1. Press button and hold until ashes ON and set temperature (setting in
Thermostatic Mode) displayed.
2. To continue, press button or wait. , OFF displayed, temperature ashes.
3. Select off temperature by pressing or button.
4. To conrm, press button.
NOTE: The on (Thermostatic) and off set temperature are the same for each day.
5.
ashes, press or to choose between ,
:
,
, , , , , , .
.
6. To conrm, press button.
selected.
DAY SETTING
7.
,1, ON displayed, is displayed shortly, and hour ashes.
8. To select hour, press or button.
9. To conrm, press button. , 1, ON displayed, displayed shortly, and
minutes ash.
10. To select minutes, press or button.
11. To conrm, press button.
12.
, 1, OFF displayed, is displayed shortly, and hour ashes.
13. To select hour, press or button.
14. To conrm, press button. , 1, OFF displayed, displayed shortly and
minutes ash.
15. To select minutes, press or button.
16. To conrm, press .
ON TIME SETTING (PROGRAM 1)
OFF TIME SETTING (PROGRAM 1)
ON
AM
PM
OFF
Figure 37: Temperature
setting.
ON
AM
PM
OFF
Figure 38: Day setting ALL.
ON
AM
PM
OFF
Figure 39: On time setting
(program 1).
ON
AM
PM
OFF
Figure 40: On time setting
(program 1).
i20 TOFINO
20 150317-32
5055.980-A