Pacific energy SUMMIT INSERT SERIES - B Operating instructions

190112-24 SINB.BODY 5055.5112
SAFETY NOTICE
If this stove is not properly installed, a house
re may result. For your safety, follow the
installation directions. Consult local building
or officials about restrictions and installation
inspection requirements in your area.
IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER
SAVE THESE INSTRUCTIONS
TESTED and LISTED
to ULC S628 / UL 1482
Meets the U.S. Environmental Protection
Agency's July 1990 Particulate Emission
Standards
MODEL:
SUMMIT INSERT
SERIES - B
Summit
Wood Insert
INSTALLATION
AND OPERATING
INSTRUCTIONS
SERIAL #

2 SINB.BODY 190112-24
Contents
Safety............................................................................................ 3
Clearances ................................................................................... 3
Masonry or Factory Built Fireplace........................................................ 3
Mantel Clearances................................................................................. 5
Dimensions .................................................................................. 5
Installation.................................................................................... 6
Fireplace Specications......................................................................... 6
Into a Masonry Fireplace ....................................................................... 6
Full Flue Liner - (Required in Canada).................................................. 7
Direct Flue Connection .......................................................................... 7
Into a Factory Built Fireplace ................................................................. 8
Combustion Air ...................................................................................... 8
Surround Assembly and Installation ...................................................... 9
Fan Speed Controller Relocation..........................................................11
Operation.................................................................................... 13
Wood Selection.....................................................................................13
How to Test Your Wood .........................................................................13
Lighting the Fire....................................................................................13
Normal Operation .................................................................................13
Restarting After Extended or Overnight Burns......................................13
More Wood, More Heat.........................................................................14
Proper Draft ..........................................................................................14
Ash Removal ........................................................................................14
Disposal of Ashes .................................................................................14
Blower......................................................................................... 14
Blower Operation..................................................................................14
Electrical Supply ...................................................................................14
Creosote ..................................................................................... 15
Formation and Need for Removal.........................................................15
Chimney Fires.......................................................................................15
In Case of a Chimney Fire ....................................................................15
Avoiding a Chimney Fire.......................................................................15
Maintenance............................................................................... 16
Baffle Removal......................................................................................16
Appendix A................................................................................. 17
Understanding & Operating Your Pacic Energy Stove.........................17
Troubleshooting ....................................................................................18
Firebrick Installation.................................................................. 19
Replacement Parts .................................................................... 20
Label.................................................................................................... 23
NOTE:
WE STRONGLY
RECOMMEND THAT
SMOKE DETECTORS BE
INSTALLED.
If smoke detectors have been previ-
ously installed, you may notice that
they are operating more frequently.
This may be due to curing of stove
paint or fumes caused by accidentally
leaving the re door open. Do not
disconnect the detectors. If neces-
sary, relocate them to reduce their
sensitivity.
SAFETY NOTICE:
If this stove is not
properly installed, a
house re may result.
For your safety, fol-
low the installation
instructions. Contact
local building or re
officials about restric-
tions and installation
inspection require-
ments in your area.
Please read this entire manual before
you install and use your new room
heater. Failure to follow instructions
may result in property damage, bodily
injury, or even death.

SINB.BODY 190112-24 3
3
47
”
Minimum Clearances to Combustibles
(Measured From Insert Body)
Adjacent Sidewall ..........................8 in. (203 mm.)
Mantel..........................................26 in. (660 mm.)
12" Mantel with Shield .................20 in. (508 mm.)
(with part # SINB.MSMBKA)
Top Facing ...................................26 in. (660 mm.)
with Mantel Shield .......................20 in. (508mm)
(with part # SINB.MSMBKA)
Side Facing (1.5 in. extension) ...... 8 in. (203 mm.)
Safety
Please read this entire manual before installation
and use of this wood burning insert.Failure to follow
these instructions could result in property damage,
bodily injury or even death.
We strongly recommend that smoke detectors be installed.
If smoke detectors have been previously installed, you may
notice that they are operating more frequently. This may be
due to curing of stove paint or fumes caused by accidentally
leaving the re door open. Do not disconnect the detectors.
If necessary, relocate them to reduce their sensitivity.
SAFETY NOTICE: If this stove is not properly installed, a
house re may result. For your safety, follow the instal-
lation directions. Consult local building or re officials
about restrictions and installation inspection require-
ments in your area.
Clearances
Masonry or Factory Built Fireplace
The minimum required clearances to surrounding combus-
tible materials when installed into a masonry or factory built
replace are listed below and in gure #1.
Fig. # 1
Mantel or Top Facing
Side Facing
Fireplace
Hearth
Adjacent Wall
NATIONAL
FIREPLACE
INSTITUTE
CERTIFIED
www.nficertified.org
We recommend that our products be
installed and serviced by professionals
who are certified in the U.S. by the
National Fireplace Institute (NFI)
or in Canada by Wood
Energy Technical
Training (WETT)
Wood Energy
Technical Training
www.wettinc.ca
CAUTION: Unit hot while in operation. Parts of the appli-
ance, especially the external surfaces, will be hot to touch
when in operation. Keep children, clothing and furniture
away. Contact may cause skin burns.

4 SINB.BODY 190112-24
16”
Non-combustible replace
hearth
28”
23 1/8”
18”
8”8”
Fireplace hearth requirements: (Measured without the insert)
The non-combustible replace hearth must be raised 3” above an adjacent combustible oor and extend 16” in front and
8” beyond each side of the existing replace opening. A non-combustible hearth that extends a minimum 20-1/2” in front
of the replace opening may be ush to an adjacent combustible oor.
Ember protection:
Combustible oor in front of the replace insert must be protected from hot embers by non-combustible material extend-
ing 16” (USA) and 18” (CANADA) to the ring side and 8” to other sides of the unit.
Consult CAN/CSA-B365 Installation Code for Solid-Fuel-Burning appliances and equipment in Canada, and N.F.P.A.
211 Standard for chimneys, replaces, vents and Solid-Fuel-Burning appliances in USA.
16” USA
18” CANADA
Non-combustible hearth
Non-combustible oor
covering
3”
3”
3”
26”
18”
*
*
**
**
MINIMUM EMBER
PROTECTION
DIMENSIONS
MINIMUM FIREPLACE
OPENING AND HEARTH
DIMENSIONS
22 1/2” USA
24 1/2” CANADA

SINB.BODY 190112-24 5
Dimensions
40 7/8”
23 5/16”
25 3/8”
27 9/16”
B
A
28 7/8”
18”
10 7/8”
21”
6 5/8”
12 1/4”
22 15/16”
9 1/8”
Mantel Clearances
WITHOUT SHIELD WITH SHIELD
A 26” 20"
B 23 1/2” 18"
MANTEL CLEARANCE
CHART
A
B
12"
4"
REG. SURROUND O/S SURROUND
A 48 3/4” 52 3/4"
B 32 1/16” 34 1/16"
SURROUND DIMENSIONS

6 SINB.BODY 190112-24
Installation
Your Insert is designed to be installed into a masonry or fac-
tory built zero-clearance replace. The masonry replace
must be built according to the requirements of the Standard
of Chimneys, Fireplaces, Vents and Solid Fuel Burning ap-
pliances, N.F.P.A. 211 (Latest Edition) or applicable National,
Provincial, State or local codes. The installation shall conform
to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning
Appliances and Equipment. The factory built zero-clearance
replace and its chimney must be listed per UL 127 or ULC
S610 standards.
Warning: Under no circumstances is this heater to be installed
in a makeshift or "temporary" manner.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVICING ANOTHER APPLIANCE.
Fireplace Specications
Your replace is required to have the following minimum
sizes:
WIDTH (at front) 28" (711 mm)
WIDTH (at rear) 26" (660 mm)
HEIGHT 23-1/8" (587 mm)
DEPTH 18" (457 mm)
Chimney height 15' (minimum).
A metal tag is provided and is to be fastened to the back
wall of the replace, if the replace has been modied
to accommodate the insert.
Into a Masonry Fireplace
Inspect your replace for cracks, loose mortar or other physi-
cal defects. If repairs are required, they should be completed
before installing your insert.
The replace chimney must be suitable for wood burning use.
Check for creosote build up or other obstructions, especially if
it has not been in use for some time. Have chimney swept.
The existing replace damper is to be locked open or removed
completely.
WARNING: Do not remove bricks or mortar from your
existing replace.
Exception: Masonry or steel, including the damper plate,
may be removed from the smoke shelf and adjacent damper
frame if necessary to accommodate a chimney liner, provided
that their removal will not weaken the structure of the replace
and chimney, and will not reduce protection for combustible
materials to less than that required by the National Building
Code.
The Insert must be installed in accordance with local and or
national building codes. The two methods of ue connection
that are acceptable in most areas are:
Full Flue Liner: (Fig.2, Required in Canada) where a stainless
steel rigid or exible liner extends from the Insert ue collar
to the top of the chimney.
Positive Flue Connection(In U.S.A. only): where a throat
blocker plate and a short connector pipe is used.
Note: A clean-out door may be required under local codes,
when a positive ue connection is used. Consult local
codes.
Pacic Energy highly recommends the use of a full
liner as the safest installation and providing optimum
performance. When connected to a full liner, the Insert
is able to draft correctly and will prevent problems such
as difficult start-ups and smoking out the door.
Rain Cap
Stainless Steel
Rigid or Flex Liner
Fig. # 2 Full Flue Liner
Mantel or
Top Facing

SINB.BODY 190112-24 7
Full Flue Liner - (Required in Canada)
1) Measure the chimney height from the top of the existing
ue to the oor of the hearth. This will allow extra length
of liner for ashing and rain cap.
2) Feed the stainless steel liner from top of the chimney,
through the damper area and into the replace cavity.
Attach a stove connector to the bottom of the liner.
3) Remove bay top and both right & left blower covers
(Fig #4 & 6).
4) Remove casing top by removing screws on each casing
side and pulling top forward(Fig. #5).
5) Push insert into replace. Use the rear adjustment legs to
level insert. (NOTE:Adjustment legs are located in bottom
rear of insert)
6) Measure, trim and shape a top ashing to t the existing
chimney ue. Plan for a 1” to 1-1/2” overlap on each side.
Place ashing over top of the liner and seat rmly against
the tile.
7) Caulk around liner with high temp stove cement and insert
into collar. Screw in fasteners to secure.
8) Attach a rain cap to the end of the liner. A storm collar
may be used if desired.
9) Reattach casing top with screws previously removed.
Consult your local Dealer about relining your replace
chimney.
Direct Flue Connection (USA only)
1) Measure from the rst chimney ue liner tile to the top of
the Insert. Allow extra length of liner to insert into ue
tile.
2) Feed the stainless steel liner through the damper area
and into the rst chimney ue tile. Seal around pipe.
Note: A clean-out door may be required under local codes,
when a direct ue connection is used. Consult local codes.
3) Remove bay top and both right & left blower covers
(Fig #4 & 6).
4) Remove casing top by removing screws on side and pull-
ing top forward(Fig. #5).
5) Push insert into replace. Use the rear adjustment legs
to level insert.
6) Attach connector pipe to stove collar.
7) Reattach casing top and fasten.
Chimney
Flue Liner
Fig. # 5
6" Stainless Steel
Rigid or Flex Liner
Mantel or
Top Facing
Direct Flue Connection
Fig. # 3
Fig. # 4
Fig. #6
SCREWS
“Wing” Screw

8 SINB.BODY 190112-24
Into a Factory Built Fireplace
Your Insert may be installed into a factory built replace (size
permitting) with the following requirements:
1) Inspect your replace for damage or other physical de-
fects. The replace must be in good working condition.
If in doubt about its condition, seek professional advice.
Check for creosote build up or other obstructions inside
the chimney, especially if it has not been in use for some
time. Before installing, clean your chimney system thor-
oughly.
2) A full stainless steel rigid or exible ue liner meeting
type HT requirements (2100°F) per UL1777 (U.S.) or
ULC S635 (Canada) must be used for both safety and
performance. The liner must be securely attached to the
Insert ue collar and the chimney top.
3) The surround must be sealed to the replace front or the
damper area around the chimney liner must be sealed
to prevent room air entering the chimney cavity of the
replace.
4) The air ow within and around the replace must not be
altered by the installation of the Insert (i.e. no blockage of
louvers or cooling air inlet or outlet ports). This includes
the circulating air chambers in a steel replace or metal
heat circulator.
5) Alteration of the replace in any manner is not permitted
with the following exceptions:
a: external trim pieces which do not affect the operation
of the replace may be removed and stored on or within
the replace for re-assembly if the Insert is removed.
b: the chimney damper may be removed to install the
liner.
Combustion Air
Consult local building codes regarding combustion air sup-
ply. Intake or combustion air can be supplied to the Insert in
one of two ways:
1) Outside air supply: Remove cover from ash clean out in
existing replace. Place a rodent screen in place of the
cover. Install the Insert as described in the "Installation"
section, making sure not to cover the opening of the air
inlet. When installation is complete, seal surround to re-
place and anywhere else air may enter. This will ensure
combustion air is drawn from outside the house and into
the 9" x 2" intake at the lower rear of the appliance.
2) Room air supply: Loosen the two hex head bolts slightly
(DO NOT REMOVE) Remove the two screws in the cover
plate and remove, slide the cover box out and discard.Re-
place cover plate and tighten hex head bolts. Fig. #7).
Fig. # 7
SCREWS
HEX HEAD BOLTS
COVER
BOX

SINB.BODY 190112-24 9
Surround Assembly and Installation
1) Lay part A, B and C face down on a at, non-marring
surface. Fasten together with 1/4" x 1/2" bolts and nuts
provided through holes at points “D” (Fig. #8 and #10).
2) Lift the surround assembly to the upright position and make
sure the front face is at and even at the joints.
3) Assemble the three trim pieces using the enclosed hard-
ware. Slide part F into the back corners of the trim and
tighten screws. Ensure the mitred corners t tightly and
evenly (Fig. #9).
4) Slide the assembled trim over the surround from the top
(Fig. #8).
5) Tighten the retaining screws at the bottom of each trim side
(Fig. #9). If not already done, slide the entire insert out of
the replace opening about 1” or more to aid in surround
installation.
6) Remove the two screws located at the top of the left and
right panels.Remove front panels and set aside to prevent
damage (Fig. #11).
Part B
Trim
Trim
Retaining
Screw
Part F
Part A
Part C
Part A
Trim
D
D
D
1/4" Nuts
Part C
1/4" x 1/2" Long Bolts
Fig. # 8
Fig. # 9
Fig. #10
Fig. #11
Fig. # 7

10 SINB.BODY 190112-24
Surround
Securing
Flange
Screws
(3 each
side)
SCREWS
TA B
Surround screw
at Top of slot
Securing Flange
Screw at bottom
of slot.
8) Remove the surround securing anges from the replace
(Fig.13) and relocate to the pre-assembled surround.
9) Slide the securing ange up so that the fastening screws
are at the top of the slots in the surround. (Fig.14 & 15)
7) Remove wing screws on each side of the Bay top and set
Bay top aside to prevent damage. (Fig. #12).
“Wing” Screw
10) Slide the pre-assembled surround behind the ash lip.
Ensure that the electric supply cord is located in the slots
in the base of the surround.
11) Once the surround is fastened to the insert, in order to
maximize heated air discharge efficiency, the surround can
be pulled upward so that the fastening screws are at the
lowest end of the surround securing ange slots.
(Fig.16)
12) Push the entire appliance back until the surround assembly
is in contact with the replace structure.
13) Replace the front panels ensuring that the tabs (Fig.17)
on the lower edge of the panels are located into the slots
in the ashlip, secure with screws (Fig.11).
14) Position the decorative bay top onto the rebox top. Align
and refasten the wing screws.
Fig. #12
Fig. # 15
Fig. # 17
Screw at top
of slot.
Fig. # 13
Fig. # 14
Fig. # 16

SINB.BODY 190112-24 11
Fan Speed Controller Relocation
The fan speed controller is factory installed under the ash lip
on the right hand side. If required, it can be relocated to the
left side by following the instructions below. To make this as
easy as possible, it is suggested that this be done prior to
tting the surround and installation into the replace:
1) Remove the screw located at the top of the left and right
panels.
2) Lift up on each panel and remove. Set aside to prevent
damage.
3) Disconnect the wires from the fans (LHS & RHS) and
thermal snap switch. Take note of where the wires are
routed and secured. They must be positioned correctly to
avoid damage.
`
4) Loosen the two bolts that secure the ash lip to the rebox,
carefully lift up the ash lip and remove from the rebox and
unscrew the wire support tabs.
5) Remove the two screws securing the speed controls as-
sembly to the ash lip.The cover plate on the opposite side
can also be removed at this time.
6) Remove the control assembly from the right hand side of
the ashlip. Flip it over and reattach on the left hand side
of the ashlip. Use the upper screw holes for best align-
ment.
BOLTS
SCREWS
SCREWS
Fig. # 18
Fig. # 19
Fig. # 20
Fig. # 21
Fig. # 22
Fig. # 23 Fig. # 24

12 SINB.BODY 190112-24
8) Remove Thermal switch from right hand fan mounting
bracket and relocate to left hand fan mounting bracket.
Fig #27&28
9) Reconnect the wires to the fans (Fig.29) and thermal snap
switch (Fig.30), ret ash lip, sides and top. Ensure that
the power cable is correctly routed through the surround
and it is not touching the rebox side. Wire placement is
important to prevent damage to wires.
7) Route cable from speed control to fan and reattach wire
support tabs on the underside of the ash lip. Note wire
positions. (Fig.25 & Fig.26)
WIRE SUPPORT TABS
Fig. # 25
Fig. # 26
Fig. # 28Fig. # 27
Fig. # 29
Fig. # 30

SINB.BODY 190112-24 13
Operation
Wood Selection
This heater is designed to burn natural wood only. Higher
efficiency and lower emissions generally result when burning
air-dried seasoned hardwoods, as compared to softwoods or
too green or freshly cut hardwoods.
Wood should be properly air dried (seasoned) for six months
or more. Wet or undried wood will cause the re to smoulder
and produce large amounts of creosote. Wet wood also pro-
duces very little heat and tends to go out often.
DO NOT BURN:
-*Salt water wood -Coal/charcoal
-Treated wood -*Garbage/Plastics
-Wet or green wood -Solvents
* These materials contain chlorides which will rapidly destroy
metal surfaces and void warranty.
Do not burn anything but wood. Other fuel, e.g. charcoal,
can produce large amounts of carbon monoxide, a tasteless,
odourless gas that can kill. Under no circumstances should
you attempt to barbecue in this heater.
How to Test Your Wood
Add a large piece of wood to the stove when it has a good,
large bed of coals. It is dry if it is burning on more than one
side within one minute. It is damp if it turns black and lights
within three minutes. If it sizzles, hisses and blackens without
igniting in ve minutes it is soaked and should not be burnt.
WARNING: Do not use grates or andirons to elevate the
fuel. Burn directly on the rebricks. Replace broken or
missing bricks. Failure to do so may create a hazardous
condition.
Your Pacic Energy heater is designed for maximum overall
efficiency at a moderate ring rate. Overring is hazardous
and a waste of fuel. Too slow a burn contributes to creosote
buildup and lowers combustion efficiency.
Lighting the Fire
WARNING: Never use gasoline, gasoline-type lantern
fuel, kerosene, charcoal lighter uid, or similar liquids
to start or ‘freshen up’ a re in this heater. Keep all such
liquids well away from the heater while in use.
1) Adjust air control to "H" (high) position (pushed to the far
left) and open door.
2) Place crumpled newspaper in the centre of the heater
and criss-cross with several pieces of dry kindling. Add
a few small pieces of dry wood on top.
3) Ignite the paper and close the door.
4) After the re has established itself, open the door and add
a few small logs. Close door.
5) Begin normal operation after a good coal base exists and
wood has charred.
Normal Operation
1) Set air control to desired setting. If smoke pours down
across the glass (waterfall effect), this indicates you have
shut the control down too soon or you are using too low a
setting. As every home’s heating needs vary (i.e. insula-
tion, windows, climate, etc.), the proper setting can only
be found by trial and error and should be noted for future
burns.
2) To refuel, adjust air control to "H" (high) position (pushed
to the far left) and give the re time to brighten. Open
door slowly, this will prevent backpuffing.
3) Use wood of different shape, diameter and length (up
to 20"). Load your wood endwise and try to place the
logs so that air can ow between them. Always use dry
wood.
4) Do not load fuel to a height or in such a manner that
would be hazardous when opening the door.
5) For extended or overnight burns, unsplit logs are preferred.
Remember to char the wood completely on "H" (high)
setting before adjusting air control for overnight burn.
WARNING: Always keep the loading door closed when
burning. If the door is left partly open, gas and ames
may be drawn out of the replace stove opening creating
risks from re and/ or smoke.This heater is not designed
for open door burning, unless a manufacturer supplied
screen is used.
DO NOT OVERFIRE THIS HEATER: Attempts to achieve
heat output rates that exceed heater design specica-
tions can result in permanent damage to the heater and
chimney.
WARNING: No alteration or modication of the combus-
tion air control assembly is permitted. Any tampering
will void warranty and could be very hazardous.
Do not store/place wood or other combustibles within
the required clearances surrounding the unit.
Restarting After Extended or Overnight
Burns
1) Open door and rake hot embers towards the front of the
heater. Add a couple of dry, split logs on top of embers,
close door.
2) Adjust air control to “H” (high) position (pushed to the far
left) and in just a few minutes, logs should begin burn-
ing.
3) After wood has charred, reset air control to desired set-
ting.
4) When burning at a slow rate for extended periods, oc-
casionally maintain a strong re under supervision for a
couple of hours to relieve rebox and chimney deposits
as well as any of the deposits on the glass.
WARNING: This method is not a substitute for regular
chimney inspections and cleaning.
5) To achieve maximum ring rate, set control to “H” (high)
position (pushed to the far left). Do not use this setting
other than for starting or preheating fresh fuel loads.

14 SINB.BODY 190112-24
More Wood, More Heat
Seasoned wood has approximately 7500 BTU’s per pound.
If you put 10 pounds of wood in your stove for an eight hour
burn the wood will be producing 9375 BTU’s per hour. (7500
BTU x 10 lbs / 8 hrs. = 9375 BTU’s per hr.). If you put 20
lbs of wood in your stove for an eight hour burn you will get
18,750 BTU’s per hr. (7500 BTU x 20 lbs / 8 hrs. = 18,750
BTU’s per hr.). This is only an example and is based on
100% efficiency. In reality, your stove should perform above
the 80% range.
Experience will give you the right settings for proper combus-
tion and efficient burning. Remember, the air inlet setting is
affected by variables such as type of wood, outside tempera-
ture, chimney size and weather conditions.With practice, you
will become procient in operating your heater and will obtain
the performance for which it was designed.
Proper Draft
1) Draft is the force which moves air from the appliance up
through the chimney. The amount of draft in your chimney
depends on the length of the chimney, local geography,
nearby obstructions and other factors.
2) Too much draft may cause excessive temperatures in the
appliance. An uncontrollable burn or a glowing red stove
part or chimney indicates excessive draft.
3) Inadequate draft may cause backpuffing into the room and
plugging of the chimney. Smoke leaking into the room
through appliance and chimney connector joints indicates
inadequate draft.
Ash Removal
Whenever ashes get 3 to 4 inches deep in your rebox, and
when re has burned down and cooled, remove excess ashes.
Leave an ash bed approximately 1 inch deep on the rebox
bottom to help maintain a hot charcoal bed.
Disposal of Ashes
Ashes should be placed in a metal container with a tight t-
ting lid. The closed container of ashes should be placed on
a non-combustible oor or on the ground, well away from all
combustible materials, pending nal disposal. If the ashes
are disposed of by burial in soil or otherwise locally dispersed,
they should be retained in the closed container until all cinders
have thoroughly cooled. Other waste should not be placed
in this container!
Blower
The Insert comes equipped with twin variable speed cir-
culating air blowers. The blower system is thermostatically
controlled for automatic operation, as well as manually with
a convenient bypass switch.
Blower Operation
Automatic: To operate the blowers automatically, push the
rocker switch to the “OFF” position and set the fan speed
control to a desired setting.
This will allow the blowers to turn on automatically once the
Insert has come up to operating temperature. It will also shut
the blowerS off after the re has gone out and the appliance
has cooled to below a useful heat output range.
Manual: To manually operate the blowers, push the rocker
switch to the “ON” position and set the fan speed control to a
desired setting. This will bypass the temperature switch and
allow full control of the blowers.
Suggested settings:
- Combustion air control setting of “L” (low) position (pushed
to the far right), operate blower speed control on “Low”.
- Combustion air control set at anything above “L” (low),
operate blower speed control at desired setting.
Electrical Supply
Circulating air blower electrical rating; 115V, 60 Hz, 0.7 A.
For your protection against shock hazard, use only a properly
grounded outlet that will accept a three-pronged plug. Do
not cut or remove the grounding prong. Do not route power
cord under unit. Power cord must be routed to avoid contact
with any hot or sharp surfaces.
Consult local codes or, in the absence of local codes, with
the current CSA C22.1 Canadian Electrical Code and in the
USA with the National Electrical Code, ANSI/NFPA 70 (lat-
est edition).
L2 (black)
G (green)
L1 (white)
Speed
Control
Blowers
Thermo
Switch
By-pass
Rocker Switch
Electrical Rating : 115 V, 60 Hz, 0.7A
Fig. # 31

SINB.BODY 190112-24 15
In Case of a Chimney Fire
1. Prepare to evacuate to ensure everyone’s safety. Have
a well understood plan of action for evacuation. Have a
place outside where everyone is to meet.
2. Close air inlets on stove.
3. Call local re department. Have a re extinguisher handy.
Contact your local re authority for further information on
how to handle a chimney re. It is most important that
you have a clearly understood plan on how to handle a
chimney re.
4. After the chimney re is out, the chimney must be cleaned
and checked for stress and cracking before starting an-
other re. Also check combustibles around chimney and
the roof.
- The services of a competent or certied installer, (certied
by the Wood Energy Technical Training program (WETT) - in
Canada, Hearth Education Foundation (HEARTH) - in U.S.A.,)
are strongly recommended.
Avoiding a Chimney Fire
There are two ways to avoid chimney res:
1. Do not let creosote build up to a point where a big chimney
re is possible.
2. Do not have res in the heater that may ignite chimney
res. These are hot res, such as when burning household
trash, cardboard, Christmas tree limbs, or even ordinary
fuel wood; (eg. with a full load on a hot bed of coals and
with the air inlet wide open).
Creosote
Formation and Need for Removal
When wood is burned slowly, it produces tar and other or-
ganic vapours, which combine with expelled moisture to form
creosote. The creosote vapours condense in the relatively
cool chimney ue of a slow burning re. As a result, creosote
residue accumulates on the ue lining. When ignited, this
creosote makes an extremely hot re. The chimney connec-
tor and chimney should be inspected at least once every two
months during the heating season to determine if a creosote
buildup has occurred. If creosote has accumulated, it should
be removed to reduce the risk of a chimney re.
1. Highest smoke densities occur when a large amount of
wood is added to a bed of hot coals and the air inlet is
closed. The heated wood generates smoke, but without
ample air, the smoke cannot burn. Smoke-free, clean
burning requires small fuel loads, two or three logs at a
time or 1/4 to 1/2 of a fuel load and leaving the air inlet
relatively wide open, especially during the rst 10 to 30
minutes after each loading, when most of the smoke
generating reactions are occurring. After 30 minutes or
so, the air inlet can be turned down substantially without
excessive smoke generation.Wood coals create very little
creosote-producing smoke.
2. The cooler the surface over which wood smoke is pass-
ing, the more creosote will be condensed. Wet or green
wood contributes signicantly to creosote formation as the
excess moisture that is boiled off cools the re, making
it difficult for the tars and gasses to ignite, thus creating
dense smoke and poor combustion. This moisture-laden
smoke cools the chimney, compounding the problem by
offering the smoke the ideal place to condense.
In summary, a certain amount of creosote is inevitable and
must be lived with. Regular inspection and cleaning is the
solution. The use of dry, seasoned wood and ample combus-
tion air will help to minimize the buildup.
Chimney Fires
The result of excessive creosote buildup is a chimney re.
Chimney res are dangerous. Chimney inside temperatures
can exceed 2000 degrees F. This causes much higher than
normal temperatures in the chimney and on its exterior sur-
faces thus ignition of nearby or touching combustible material
is more likely during a chimney re. Proper clearances are
critical during such a re.
Chimney res are easy to detect; they usually involve one or
more of the following:
- Flames and sparks shooting out of the top of the chim-
ney
- A roaring sound
- Vibration of the chimney

16 SINB.BODY 190112-24
7. Do not store wood within heater installation clearances, or
within the space required for fuel loading and ash removal.
Keep the area around the heater clean and free of all loose
combustibles, furniture, newspapers, etc.
8. If gold door requires cleaning, use mild soap and water only.
Use of abrasive cleaners will void warranty.
9. Establish a routine for the fuel, wood burning and ring tech-
nique. Check daily for creosote buildup until experience shows
how often you need to be cleaning to be safe.
10. Be aware that the hotter the re, the less creosote is deposited.
Weekly cleaning may be necessary in mild weather, even
though monthly cleaning is usually enough in the coldest
months when burning rates are higher.
11. Instruct all members of your family on the safe operation of
the heater. Ensure they have enough knowledge of the entire
system if they are expected to operate it. Stress the section
on chimney res and the importance of following the steps
outlined in “In Case of Chimney Fire”.
Baffle Removal
The Insert and pipe should be removed from the replace
to clean and inspect. Only if this is not possible should you
remove baffle assembly.
DO NOT OPERATEWITH BAFFLEASSEMBLY OR INSULA-
TION REMOVED.
Baffle Assembly Removal
Remove retaining pin at the back top of the rebox, just un-
der the baffle. Lift baffle up and pull forward to disconnect
from the supply tube. Tilt baffle sideways to drop down and
remove from rebox.
Inspect gasket between baffle and supply tube. If necessary,
replace with gasket # 3139.5 available from your nearest
Pacic Energy Dealer.
Re-install baffle assembly and insulation by reversing order.
It is recommended to inspect the liner and connector
monthly and to have the liner cleaned annually or more
frequently if required.
Maintenance
1. Burn wood only, dry and well seasoned. The denser or
heavier the wood when dry, the greater its heat value. This
is why hardwoods are generally preferred. Green or wet
wood should not be used, as it will reduce heat output,
as well as contributing signicantly to creosote buildup.
WARNING: Never use chemicals or any other volatile
liquid to start a re. Do not burn garbage, or ammable
uids such a gasoline, naptha, or engine oil. We strongly
recommend that smoke detectors be installed.
2. Remove ashes frequently. Embers can roll out the door and
create a re hazard. Maintain a 1" minimum ash base.
3. If glass becomes darkened through slow burning or poor wood,
it can readily be cleaned with any replace glass cleaner when
stove is cold. Never scrape with an object that might scratch
the glass. The type and amount of deposit on the glass is a
good indication of ue pipe and chimney buildup.A light brown
dusty deposit that is easily wiped off usually indicates good
combustion and dry, well-seasoned wood and therefore rela-
tively clean pipes and chimney. On the other hand, a black,
greasy deposit that is difficult to remove is a result of wet and
green wood and too slow a burning rate. This heavy deposit
is building up at least as quickly in the chimney.
WARNING: Only use materials and components supplied
or specied by the manufacturer when doing maintenance
or replacements.
4. DOOR GASKET - The gasket used by Pacic Energy requires
only light pressure to seal. This will prolong seal life. It is
important that the door seal be maintained in good condition.
Periodically inspect seals and replace if necessary. Follow
instructions included in the DR31.WDGKIT kit obtainable from
your nearest Pacic Energy Dealer.
5. DOOR GLASS - Do not slam loading door or otherwise impact
glass. When closing door, make sure that no logs protrude to
impact the glass. If the glass gets cracked or broken, it must
be replaced before using the stove. Replacement glass can
be obtained from your Dealer. The size required is 9-1/2 x
17-1/2 (Summit Insert) x 5 mm Robax. Ceramic glass must
be used. Do not substitute with any other type.
To remove broken glass, undo the four retaining screws and remove
the frame noting position for re-assembly. Remove all particles of
glass. Be careful as they are very sharp.Install new glass complete
with gasket. Replace frame and screws.
WARNING: Do not overtighten, tighten screws very
carefully.
- Do not clean glass when hot
- Do not use abrasive cleaners on glass
6. The area where boost combustion air enters the rebox must
be kept clear of excessive ash buildup which will block air ow.
This area is at the front of the rebox.

SINB.BODY 190112-24 17
Appendix A
Understanding & Operating Your Pacic Energy Stove
The Pacic Energy line of woodstoves is a culmination
of years of research and development. Designed to be
efficient, clean-burning and user-friendly, this heater will
give you yearsofwarm service.However, aknowledgeable
operator is still the most important factor for maximum
performance and part of this is understanding the basic
functions of this design.
Traditional wood stoves had a basic combustion system
which allowed a considerable amount of heat energy
to escape up the chimney as unburned gases and
particulates (smoke).
Pacific Energy has
designed a system that
solves the problem by
burning the smoke and
releasing the additional
heat to the room.
This system has
two critical design
features:
1. Above re secondary
air injection:
The hollow "air baffle"
injects super-heated
secondaryairjustabove
the load.With the stove
at the proper operating
temperature, this will
create a secondary
amethatwillbeevident
for approximately 1/3 of
the total burn time.
2.High mass and thermal insulation:
The high mass (weight) acts as a heat storage and the
thermal insulation keeps the combustion zone hot.Active
aming takes place during the rst part of the burn.During
this stage, heat is stored in the mass of the unit and is
later released slowly and evenly. As wood chars, active
aming will diminish. This clean charcoal burning stage
will last for a considerable length of time and refueling
should be avoided until the charcoal base has become
quite small.
OPERATING TIPS
1. Always use dry, seasoned rewood, up to 18" long.
Load wood endwise, a mixture of large and small pieces,
on top of a good ash base (1" minimum).
2. Operate on a medium to high setting, for up to 1
hour from cold start. After the initial warm up period,
refuel and leave the air control on a medium setting for
5 to 10 minutes more
and then set the air
control to the desired
position.
3. If a slow burn is
desired, set the air
control to low. Active
secondary burning
should be present
above the wood load.
If it is not present
or goes out shortly
after, proper operating
temperature has not
been reached and the
stove needs additional
warm up time.
For additional
operating, safety
and maintenance
information, refer to the
installation manual.
4 -Secondary Combustion Zone
5 -Radiant Heat
6 -Convected Heat
1 -Boost Air
2 -Main Combustion Air
3 -Air Wash System

18 SINB.BODY 190112-24
Troubleshooting
Problem Cause Cure
Glass is Dirty 1. Wood is wet - Use dry wood
2.Turning down air control - Do not turn down until
or damper too soon a) there is a good bed of coals
b) the wood is charred
3.Draft too low - Improper chimney height and / or diameter
- Chimney plugged or restricted, inspect and
clean
- Provide outside air for combustion
4. Door gasket leakage - Replace gasket
- Check latch
Excessive Creosote Buildup - See 1,2,3, above.
Low Heat Output 1. Wood is wet - Use dry wood
2.Fire too small - Build a larger re
3.Draft too low - Chimney plugged or restricted, inspect and
clean
Won't Burn Overnight 1. Air control is set too high - Set control lower
2. Not enough wood - Unsplit wood is preferred for overnight burns
3. Draft too high - Excessive chimney height and/or diameter
Stove Won't Burn 1. Combustion air supply blocked - Check outside air supply for obstruction
- Check that room air cover is removed
2.Draft too low - Chimney plugged or restricted, inspect and
clean
- Chimney oversized or otherwise unsuitable,
consult Dealer

SINB.BODY 190112-24 19
ITEM SIZE PART NUMBER
A 1 1/2” X 4 1/2” X 1 1/4” (39 mm x 115 mm x 32 mm) 248.001
B 4” X 4 1/2” X 1 1/4” (102 mm x 115 mm x 32 mm) 246.001
C 7 1/4” X 4 1/2” X 1 1/4” (184 mm x 115 mm x 32 mm) 245.001
D 9” X 4 1/2” X 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99
E 9” X 4 1/2” (cut) X 1 1/4” (230 mm x 115 mm (cut) x 32 mm) 3245.011
F 9” X 3 1/2” X 1 1/4” (102 mm x 115 mm x 32 mm) 3245.501
Summit Insert Wood Stove
This package contains 17 full-size firebricks, as well as 7 various cut-size bricks.
With the woodstove in the upright position, install firebricks as follows:
1) Place the firebricks on the bottom of the unit first. Use 7 full-size (D) and 3 cut
bricks (C & 2E).
2) Next install the side firebricks, 4 full-size bricks on each side of the firebox as
shown.
3) Finally install 2 full-size and 2 cut firebricks against the rear wall as shown.
F
C
E
D
D
Firebrick Installation

20 SINB.BODY 190112-24
1......Bay Top (c/w Washers and Nuts)................... SINS.50374524
2......Casing Top, Back ............................................................. 3502
3......Casing Top, Front........................................................ 3502.51
4......Casing Back...............................................................3504.001
5......Air Deector..................................................................... 3505
6......Front Panel, Left ..................................................... SINB.3544
7......Casing Side, Left ............................................... SINS.3509.51
8......Door Catch (c/w Bolt) .......................................WODC.1461A
9......Ash Lip ........................................................... SINS.50374523
10....Quadrant Shield...........................................................3536.01
11....Casing Bottom ..................................................................3501
12....Casing Side, Right........................................................ 3503.5
13....Front Panel, Right ................................................... SINB.3543
14....Secondary Air Box Gasket...................................... 5068.3237
15....Secondary Air Box (c/w Gasket)..........................SUMM.3140
16....Quadrant Cover ................................................................3514
17....Air Shutter Assembly (c/w Spring. Washer and Cap)..............
SUMM.531
18....Glass Clamp Kit (c/w Screws) .............................SUMM.1425
19....Glass Bar Kit (2 pcs.).......................................SUMM.212501
........Glass Gasket Kit (not shown) .....................................2083.01
20....Rep. Glass (c/w Glass Gasket).......................... DR46.GLKIT
21....Door Gasket Kit ............................................... DR31.WDGKIT
22....Door Casting, Arched Black................................... CAST.46ST
........Door Casting, Arched Gold .................................CAST.46GDA
.......... Door Casting Arched Nickel...............................CAST.46NI
.......... Door Casting Arched Brushed Nickel...............CAST.46BNA
23....Door Handle Assembly (c/w Wood Handle and Nut) ...............
WODC.4147C
24....Baffle Pin ........................................................... SSER.125001
25....Brick Rail Set(2 pcs. required) ......................SUMM.RAILSET
26....Baffle Kit (includes side insulation, 2pcs) .........SUMB.BAFKIT
27....Flame Shield (c/w Bolt, Washer and Nut).............. SINB.3525
28....Boost Manifold........................................................... 3105.111
29....Firebrick - 9" x 4 1/2" x 1 1/4" (19 pcs. required)......... 5096.99
........Firebrick Set.......................................................BRIC.SUMMA
30....Replacement Blower Assembly ...............................................
........Right Blower Assy. .............................................SPND.502454
........Left Blower Assy.................................................SPND.502453
31....Standard-Size Surround Assembly, Embossed Panels ...........
3/4" wide x 32" high
........Over-Size Surround Assembly, Plain Panels ...........................
........52 3/4" wide x 34" high (not shown)
32....Control Box Mount, Right..................................................3512
33....Control Box Mount, Left ................................................... 3529
34....Control Assembly...................................................SPND.4583
........Cover Plate(not shown) ................................................... 4593
35....SINS Regular Trim, Black ..................................... SINS.35192
........SINS O/S Trim, Black (not shown)........................ SINS.35492
All parts may be ordered from your nearest Pacic
Energy dealer. Contact Pacic Energy for the location
of the dealer nearest you.
Replacement Parts
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.