Pacific energy Tofino Series User manual

WARNING: If the information in these
instructions is not followed exactly a fire
or explosion may result causing property
damage, personal injury or death.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
This appliance is suitable for installation in a
bedroom or bed sitting room.
This appliance may be installed in an after-
market permanently located, manufactured
home (USA only) or mobile home, where not
prohibited by local codes.
This appliance is only for use with the type of
gasindicatedontheratingplate.This appliance
is not convertible for use with other gases
unless a certified kit is used.
FOR YOUR SAFETY
Donot storeor use gasolineor other flammable
vapours and liquids in the vicinity of this or any
other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical Switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier call the
fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
TOFINO
TOFINO
INSTALLATION
INSTRUCTIONS
MODEL: TOFINO i40s
TOFINO i40m
(SIT & Maxitrol G6R versions)
SERIES: A
DIRECT VENT GAS INSERT
Visit www.pacificenergy.net for the most recent version of this manual
100000300
051119-48
INSTALLATION INSTRUCTIONS

Important Note for the Commonwealth of Massachusetts: ...... 3
Caution ...................................................................................... 4
Safety ........................................................................................ 5
WHAT TO DO IF YOU SMELL GAS ................................... 5
First Fire ..................................................................................... 6
Warnings and Cautions ............................................................. 6
Fireplace Dimensions .................................................................7
Tono Insert Backing Plate Dimensions .................................... 8
Existing Fireplace Preparation ................................................... 9
Clearances to Combustibles ................................................... 10
Horizontal Clearances...................................................... 10
Objects in front of Appliance ........................................... 10
Mantel Clearances ........................................................... 10
Mantel Depth ................................................................... 10
Hearth Clearance ............................................................. 10
Under Appliance .............................................................. 10
Adjustable Leveling Bolts .........................................................11
Removable Handles .................................................................11
Venting ..................................................................................... 12
Flue adapters ................................................................... 12
SIT Control Overview ............................................................... 14
Maxitrol Control Overview ....................................................... 14
Door Installation/Removal ....................................................... 15
Removal ........................................................................... 15
Installation........................................................................ 15
Panel Installation ..................................................................... 16
Installation........................................................................ 16
Bafe ....................................................................................... 18
Cleaning the ceramic glass bafe:................................... 18
Installing the ceramic bafe: ............................................ 18
Electrical Supply ...................................................................... 19
Gas Supply .............................................................................. 19
Gas Valve for SIT Conguration .............................................. 20
SIT controller.................................................................... 20
SIT gas valve.................................................................... 20
Gas valve for Maxitrol Conguration ........................................21
Maxitrol controller .............................................................21
Maxitrol gas valve .............................................................21
Gas Pressure Check / Output / Efciency ............................... 22
....................................................................................... 22
Gas Pressure Testing Procedure ............................................. 23
Damper Adjustment ................................................................ 24
Damper Adjustment:........................................................ 24
Venturi Adjustment .................................................................. 25
Glass Media Installation .......................................................... 26
Split Log Set Installation ...........................................................27
Log set Installation........................................................... 28
Manual Switch Installation for SIT Units .................................. 35
To install ON/OFF Switch ................................................. 35
Manual Switch Installation for Maxitrol Units ...........................37
To install ON/OFF Switch ..................................................37
Pairing the SIT Remote Handset and Receiver ....................... 39
Pairing the Maxitrol Remote Handset and Receiver ............... 40
Surround Installation/Removal Instructions .............................41
Installation.........................................................................41
Removal ............................................................................41
Lighting Instructions ................................................................ 42
Maintenance ............................................................................ 43
Glass Door: ...................................................................... 43
Annual Inspection:............................................................ 43
Periodically:...................................................................... 43
Wiring Diagram for SIT Proame ............................................. 44
Wiring Diagram for Maxitrol ..................................................... 45
Tono i40 Rating Labels .......................................................... 46
Rating label location .........................................................47
Table Of Contents
2051119-48 100000300i40 TOFINO

Important Note for the Commonwealth of Massachusetts:
From Massachusetts Rules and Regulations 248 5.08:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or
in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust
vent termination is less than seven (7) feet above nished grade in the area of the venting, including but not limited to decks
and porches, the following requirements shall be satised.
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas
fueled equipment,the installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm
and battery back-up is installed on the oor level where the gas equipment is to be installed, in addition, the installing
plumber or gas tter shall observe that a battery operated or hard-wired carbon monoxide detector with an alarm is installed
on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment.
It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the installation
of hard-wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard-
wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent oor level.
b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall
have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day
period, a battery operated carbon monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above
provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.
3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled
heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT
DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve
the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accor
dance with the provisions of 248 CMR 5.089(2) (a) 1 through 4.
(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54
as adopted by the Board; and
2. Product Approved side wall horizontal vented gas fueled equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with
the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall
include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the fuel
gases, but identies “special venting systems”, the following requirements shall be satised by the manufacturer.
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation
instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
3
100000300 051119-48 i40 TOFINO

This replace is equipped with a micro mesh safety screen for your protection and
must be installed with the unit. Removal of the safety screen will cause the replace
to become a burn hazard.
Caution
FOR YOUR SAFETY - Do not install or operate your Pacic Energy replace without rst reading
and understanding this manual. Any installation or operational deviation from the following
instructions voids the Pacic Energy Fireplace Warranty and may prove hazardous.
This appliance and its individual shut off valve must be disconnected from gas supply piping system
during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).
This appliance must be isolated from the gas supply piping system by closing its individual manual
shut off valve during any pressure testing of the gas supply piping system at test pressures equal to
or less than 1/2 psig (3.5 kPa).
Note: When lit for the rst time, the appliance will emit a slight odour for a couple of hours. This
is due to the curing of paints, sealants and lubricants used in the manufacturing process. This
condition is temporary. Open doors and windows to ventilate area. Smoke and fumes caused by the
curing process may cause discomfort to some individuals.
Do not use the replace if any part has been under water. Immediately call a qualied service
technician to inspect the replace and to replace any part of the control system and any gas control
which has been under water.
4051119-48 100000300i40 TOFINO

Safety
• Due to high temperatures, this gas appliance should be located out of trafc and away from
furniture and draperies.
• Children and adults should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical
barrier is recommended if there are at risk individuals in the house. To restrict access to a
replace or stove, install an adjustable safety gate to keep toddlers, young children and other at
risk individuals out of the room and away from hot surfaces.
• Clothing or other ammable material should not be placed on or near the appliance.
• A barrier designed to reduce the risk of burns from the hot viewing glass is provided with the
Surround Kit component and shall be installed.
• If the barrier becomes damaged, the barrier shall be replaced with the manufacturers barrier
for this appliance.
• Any grill, panel or door removed for servicing the unit must be replaced prior to operating.
• Installation and repair should be done by a qualied service person. The appliance should be
inspected before use and at least annually by a professional service person. More frequent
cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burners and circulating air passageways of the appliance
be kept clean.
• This appliance must not be connected to a chimney ue serving a separate solid fuel burning
appliance.
• It is our policy that no responsibility is assumed by the Company or by any of its employees or
representatives for any damages caused by an inoperable, inadequate, or unsafe condition which
is the result, either directly or indirectly, of any improper operation or installation procedures.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical Switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier call the re department.
• Installation and service must be performed by a qualied installer, service agency or the gas
supplier.
5
100000300 051119-48 i40 TOFINO

NOTE: Fireplace may take up to
30 seconds to ignite each time the
“ON” button has been selected
First Fire
When lit for the rst time, the replace will emit a slight odour for a couple of hours. This is due to
the curing of paints, sealants and lubricants used in the manufacturing process. This condition is
temporary. Open doors and windows to ventilate area. Odour caused by the curing process may
cause discomfort to some individuals.
It is normal for replaces fabricated of steel to give off some expansion and/or contraction noises
during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or
cook stove oven.
Warnings and Cautions
WARNING
Fire Hazard. Can cause severe injury or death
The Receiver causes ignition of the appliance. The appliance can turn on suddenly. Keep away from the
appliance burner when operating the remote system or activating manual bypass of the remote system.
WARNING
Shock Hazard. Can cause severe injury or death
This device is powered by line voltage. Do not try to repair this device. In no way is the enclosure to be
tampered with or opened. Disconnect from line voltage before performing any maintenance.
6051119-48 100000300i40 TOFINO

Tono i40 SIT Tono i40 Maxitrol
A 4” 4”
B 6” 6”
C 15 3/4” 15 3/4”
D 17 3/8” Use dimension “C”
E 36 1/8” 36 1/8”
F 22 7/8” 22 7/8”
G 18 1/4” 18 1/4”
H 24 1/8” 24 1/8”
I 27” 27”
J 34 1/2” 34 1/2”
K 3” x 4” 3” x 4”
L 15 5/8” 15 5/8”
M 25” 25”
Fireplace Dimensions
E
I
J
F G H
C D
B
A
K
L
M
Figure 1: Tono Dimensions.
7
100000300 051119-48 i40 TOFINO

Tofino Insert Backing Plate Dimensions
Tofino i40
B
A
Figure 2: Tono Surround dimensions.
HEIGHT / WIDTH A B
REGULAR 28” 42”
OVERSIZED 31” 44”
8051119-48 100000300i40 TOFINO

Figure 3: Minimum openings.
Dimension i40 SIT i40 Maxitrol
A 17 7/8” 16 1/4”
B 24 5/8” 24 5/8”
C without handles 35” 35”
C with handles 36 1/2” 36 1/2”
Existing Fireplace Preparation
The Tono Gas inserts are certied to be installed into pre-existing approved replace. The minimum existing
opening replace requirements are listed in Figure 3 below.
Before installing the Tono inserts, have the chimney and replace swept including ash dumps and clean
outs. Clean and remove any creosote and soot residue that may cause odors and stains after the insert
has been installed. The replace chimney should be in good working order and made of non-combustible
material. Make sure chimney clean-outs t properly.
When preparing an existing replace to install a gas insert, any modications that will compromise the
integrity of the existing replace are not allowed. To make way for the inserts’ venting, the replace ue
dampener may be blocked open or removed. Refractory, glass doors, screen rails, screen mesh and log
grates can be removed from the replace before installing the insert. Also, smoke shelves, shields and
bafes may be removed if attached by mechanical fasteners. Cutting any sheet metal parts of the replace,
in which the gas replace insert is to be installed, is prohibited.
If the factory-built replace has no gas access hole(s) provided, an access hole of 1.5” dia. (37.5mm) or
less may be drilled through the lower sides or bottom of the rebox in a proper workmanship like manner.
This access hole must be plugged with non-combustible insulation after the gas supply line has been
installed.
Note: SIT controlled installations require that an electrical outlet be installed either into an existing
fireplace cavity before the Tofino is installed, or alternatively, the power cord can access a pre-existing
power outlet elsewhere in the room by way of knock-out openings located on either side of the
backing plate. See “Figure 34” on page 19.
9
100000300 051119-48 i40 TOFINO

• Fireplace Surrounds and
oversize backing plates for
larger replace openings
located on page 8.
Mantel Clearance
Mantel Depth
Hearth
Clearance
Figure 4: Mantel clearance.
i40
Horizontal clearance to adjacent sidewall combustibles. Refer to Figure 5
20” From center of replace to nearest combustible or to backing plate, whichever is furthest
Side wall
Side wall
Figure 5: Horizontal clearance to combustibles.
Horizontal Clearances
Clearances to Combustibles
i40
Mantel Clearances
i40
Mantel Depth
35”
14”
Hearth Clearance
i40 0”
Objects in front of Appliance
i40 36”
Under Appliance
i40 0”
10 051119-48 100000300i40 TOFINO

3/4”
Figure 8: Removable handles.
Adjustable leveling bolts
This replace comes with two leveling bolts
used to adjust the angle of the front of
the replace (Figure 6) relative to the wall
in which it’s installed. The bolts are pre-
installed. There is also a single rear leveling
adjustment bolt located at the center of the
bottom oor. Use these adjustments along
with the bubble sight (Figure 7) to level the
Tono replace.
Adjustable Leveling Bolts
Side to side levelling
adjustments
Rear to front levelling
adjustment
Bubble
sight
Figure 6: Leveling adjustments.
Removable Handles
The handles used to lift and maneuver the Tono into position can be removed in order to accommodate a
narrower horizontal replace opening. By removing each of the two handles, a full 1 1/2” can be saved.
Figure 7: Bubble sight.
Handle screws
Figure 9: Removable handle screws.
11
100000300 051119-48 i40 TOFINO

Flue adapters
The Tono i40 uses 3” ex tubing for the air intake and 4” ex tubing for the air exhaust. The Tono i40 ships
with a ue adapter which ts onto the top of the rebox and is afxed with a connection bolt (Figure 11).
Depending on the amount of room available for the installation of the Tono, the installer may want to remove
the ue adapter and attach it to the ex tubes which will have previously been inserted down the chimney.
The installer must make sure that the air intake vent and air exhaust vents attach to the correct ports on
both the ue adapter and the vent terminal. The vent terminal and the ue adapter are marked with an “I” (air
intake) and “E” (air exhaust).
3” Air intake
4” Exhaust
Figure 10: 4 x 3 inch Flue adapter.
Flue adapter
Connection
bolt
Figure 11: Tono with ue adapter mounted.
Venting
10’ to 40’ Use the 3x4 Conguration
10’ to 28’ Use the 3x4 and the 4” to 3” adapter Conguration
12 051119-48 100000300i40 TOFINO

Certified vent
terminal
Max Vent Height
40’ (12.2m)
Figure 13: Co linear venting.
Exhaust
vent
Combustion
air intake
Flue adapter
Damper
linkage
Damper adjustment
securing bolt.
(Adjustment handle
located under top
surface
Figure 12: Flue adapter components.
Only certified venting systems or components may be installed with this fireplace.
Only the following vent terminals should be used for the Tofino i40.
Min. Vent Height
10’ (3m)
Manufacturer Model Model # Venting length
Duravent High wind
terminal
DVA-CL33 10’ to 28’
Duravent High wind
terminal
DVA-CL34 10’ to 40’
ICC Co linear terminal CT3 10’ to 28’
ICC Co linear terminal CT4 10’ to 40’
Combustion
Air Intake
Exhaust
Vent
13
100000300 051119-48 i40 TOFINO
1. Measure chimney height, cut ex liner (min.10’) as required. Mark
one pipe at both ends to identify combustion air intake pipe from ue
outlet pipe.
2. Attach marked ex liner pipe to the intake side of vent terminal. Seal
and secure with sealant and screws provided. Attach the other pipe
to the outlet side of vent terminal. Seal and secure with sealant and
screws provided.
3. Insert both ex liners from top of the chimney, down through the
damper opening.
4. Attach and seal according to vent terminal manufacturers’ instructions
5. For larger chimneys, a ashing may be cut and tted to suit. Caulk the
ashing in place to seal any gaps.

SIT Control Overview
Maxitrol Control Overview
The Maxitrol controller (Figure 16) is used along with the Maxitrol gas valve (Figure 40 on page 21). The
use of the Maxitrol controller requires a remote control device (provided) unique to the Maxitrol conguration.
Instructions for using the Maxitrol remote control device are found in the Tono Operating Instructions manual.
The Maxitrol module uses 4 AA batteries. The Maxitrol remote control unit takes 2 AAA batteries.
The SIT Proame controller (Figure 14) is used along with the SIT Proame gas valve (See “Figure 38” on
page 20) . The use of the SIT Proame controller requires a remote control device (provided) unique to the
SIT Proame conguration. Instructions for using the SIT Proame remote control device are found Tono
Operating Instructions manual. The SIT module uses 4 AA batteries. The SIT Proame remote control unit
uses 3 AAA batteries.
Figure 14: SIT Proame controller module. Figure 15: Proame - SIT remote control device.
Figure 16: Maxitrol module. Figure 17: G6R remote control device.
14 051119-48 100000300i40 TOFINO

Door Installation/Removal
Figure 18: Glass door and hooks.
Removal
1. Remove the surround and backing plate from the front of the replace, “Surround Installation/Removal
Instructions” on page 41. Take care to disconnect the wire on the left hand side of the backing plate
which attaches the switch to the interior of the replace.
2. There are two handles located on the replace door (Figure 18) which must be pulled inward toward
the center of the replace to unlock the door (Figure 19). This may take some effort because the door
completes a tight seal around the rebox.
3. Remove the door and set aside.
Installation
1. Place the door over the opening of the replace.
2. There are two hooks on the top of the handles and two hooks on the bottom of the handle and so the door
must be placed squarely over the rebox opening.
3. Once the glass door is seated, close the door handles outward and inward until they stop.
4. The handle will not close completely. There will be an approximately 3/4” gap between the handles
and the door frame (Figure 20). This is normal.
5. Return the backing plate to its original position making sure to reconnect the switch wire to the backing
plate. Return the surround to its original position.
Figure 19: Unlocking the glass door.
Approx. 3/4”
gap
Figure 20: Door handles in closed position. Figure 21: Locking the glass door.
15
100000300 051119-48 i40 TOFINO

Panel Installation
The panel sets are delicate and should be handled with care.
The bafe and panel support bracket (Figure 22) retains the side panels, supports the front end of the ceramic
glass bafe, and has a shield which directs the light from the ceiling of the rebox (available on i40s models
only) down onto the log set (model dependent). It is held in place by two bolts. The bracket and its bolts
should be removed before installing the rear and side panels so that the bolts protruding from the ceiling do
not damage the panels.
Installation
1. With the above mentioned support bracket and bolts removed, hang the rear panel onto the posts
protruding from the rear wall (Figure 24 and Figure 25).
Figure 22: Bafe and panel bracket.
Side panel support tabs
Bafe support tabs
Figure 23: Bafe and panel bracket supporting
side panels.
Rear panel support posts /
support posts for rear end
of ceramic glass bafe
Figure 24: Rear wall showing panel support posts.
16 051119-48 100000300i40 TOFINO

2. Gently place the base of either of the two side panels along the edge of the rebox oor and wall. Then
slowly tilt the top part of the panels up into the edge of the wall and ceiling. Be careful that the top corner
of the panel closest to the front of the replace makes as little contact with the opening edge of the
rebox and gasket (Figure 26) as possible as this may damage the panel.
3. The rear panel is stabilized once the side panels are in place. Stabilize the side panels by installing the
glass bafe and panel bracket (Figure 22) and its bolts.
4. Install the ceramic glass bafe as outlined in “Installing the ceramic bafe:” on page 18.
Figure 25: Rear panel in place. Figure 26: Upper rebox corner and gasket.
Figure 27: Right side panel in place. Figure 28: Left side panel in place.
17
100000300 051119-48 i40 TOFINO

Ceramic glass
bafe
Front bafe
support Rear ceramic
glass bafe
& rear panel
support posts
Figure 29: Ceramic glass bafe. Figure 30: Inserting bafe into the upper corner.
Figure 31: Raising bafe above front support. Figure 32: Sliding bafe over to rest on top of supports.
Baffle
The bafe is made of ceramic glass which allows for the use of a halogen lamp feature. The halogen lamp is
only available on units using the SIT Proame conguration, the Maxitrol conguration does not include the
use of a halogen lamp.
Installing the ceramic baffle:
1. With the door removed, place one end of the bafe over one of the two upper corners so that the bafe
is resting on a rear peg and a front support (Figure 30).
2. Raise the opposite end of the bafe so that it is raised above the supports on the other side of the
rebox (Figure 31).
3. Slide the bafe over so that it is supported by all four supports (Figure 32).
Cleaning the ceramic glass baffle:
Note: Do not clean the ceramic glass bafe until the replace has been turned off long enough for the glass
door and ceramic bafe to sufciently cool down. Use glass cleaner to clean the ceramic bafe of soot or
other debris.
18 051119-48 100000300i40 TOFINO

Electrical Supply
Gas Supply
Figure 33: Electrical connection.
Knock-out for power cord
Figure 34: Knock-out for power cord.
Figure 35: Tono gas connection.
Caution: The gas line should be installed by a qualied service person in accordance with all building codes.
This section is intended as a guide for qualied technicians installing this appliance. Consult local and/or
national building codes before proceeding.
• Gas supply line connection is located on the left rear side of the insert (Figure 35). Gas connection
accepts a 3/8” N.P.T. tting. Correct gas line diameter must be used to assure proper operation and
pressure. Do not use external threads for gas connections. Use internal threads only.
• A drip leg must be installed in the gas supply line going to the gas control valve to minimize the possibility
of any loose scale or dirt within the gas supply line from entering the control valve.
Check local codes for additional requirements.
Turn on the gas supply and check that all connections are tight and leak free.
Note: SIT controlled installations require that an electrical outlet be installed either into an existing
fireplace cavity before the Tofino is installed, or alternatively, the power cord can access a pre-existing
power outlet elsewhere in the room by way of knock-out openings located on either side of the
backing plate (Figure 34).
NOTE: The appliance, when installed must be electrically grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code,
CSA C22.1.
To gas valve assembly
Figure 36: Gas shut off valve.
19
100000300 051119-48 i40 TOFINO

Figure 37: SIT control center.
Gas Valve for SIT Configuration
Figure 38: SIT Gas valve.
SIT controller
The SIT controller is mounted
onto a caddy which is located on
the left hand side of the replace
for easy access. Remove the
surround to gain access to the
controller.
SIT gas valve
The SIT gas valve assembly is
mounted onto a caddy which is
located on the right hand side
of the replace for easy access.
Remove the surround to gain
access to the controller.
20 051119-48 100000300i40 TOFINO