Pacific energy FP30AR User manual

2000418-48 FP30/FP30 AR Series B 100000811
INSTALLATION
AND OPERATING
INSTRUCTIONS
SAFETY NOTICE
If this fireplace is not properly
installed, a house re may result.
For your safety, follow the installation
instructions. Contact local building
or re ofcials about restrictions and
installation inspection requirements
in your area.
IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER.
PLEASE SAVE THESE INSTRUCTIONS.
MODEL: FP30, FP30AR
Series: B
ZERO CLEARANCE
WOOD FIREPLACE
SERIAL #
TESTED and LISTED to CAN/ULC
S610-M87 AND UL 127
Meets the Environmental Protection Agency's
May 2015 Particulate Emission Standards
Visit www.pacificenergy.net for the most recent version of this manual

Contents
Table of Contents ............................................................ 2
Efciency and BTU Output ....................................... 3
Safety and Maintenance .................................................. 4
Maintenance Checks ....................................................... 6
Weekly:...................................................................... 6
Monthly .................................................................... 6
When Cleaning the Chimney System: ...................... 6
Bafe: ....................................................................... 6
Ash Removal: ............................................................ 6
Disposal of Ashes: .................................................... 6
Secondary Air Box Cleaning ..................................... 7
Bafe Removal ................................................................ 7
Chimney Smoke and Creosote Formation ...................... 8
Creosote - Formation and need for removal:............ 8
Preventing a Chimney Fire ........................................ 8
In the event of a Chimney Fire .................................. 8
Operation ......................................................................... 9
Wood Selection ......................................................... 9
How to Test Your Wood............................................. 9
DO NOT BURN THESE MATERIALS......................... 9
Lighting a Fire.......................................................... 10
Normal Operation.................................................... 10
Restarting After Extended or Overnight Burns ....... 11
Over Firing............................................................... 11
Proper Draft............................................................. 11
Curing of the paint nish......................................... 11
Health Warning. ...................................................... 11
Ash Removal ........................................................... 11
Troubleshooting ............................................................. 12
Blower Removal ............................................................ 13
Fireplace Installation ...................................................... 15
Locating your Fireplace........................................... 15
Mobile Home Installation notes: ............................. 15
Crate Removal ........................................................ 16
Dimensions .................................................................... 16
Fireplace Clearances and Chimney Restrictions ... 16
Minimum Framing Dimensions ...................................... 17
Framing Kit Installation .................................................. 18
Assembly................................................................. 18
Installing the unit into the chase ............................. 18
Chimney Installation ...................................................... 19
Offset Chimney: ..................................................... 20
Masonry Chimney: .................................................. 21
Combustion Air .............................................................. 22
Installation:.............................................................. 22
Convection Blower Wiring ............................................. 23
Option: Remote Heat Duct Kit Installation .................... 24
Parts:....................................................................... 24
Ducting Options .................................................... 25
Duct Installation ...................................................... 26
Remote Heat Kit Wiring ......................................... 28
Chase Air Inlets ............................................................. 29
Finshing The Chase ....................................................... 29
Hearth ............................................................................ 30
Ember Protection .......................................................... 31
Safety Strip ............................................................. 31
Ember Protector...................................................... 31
Finishing Clearances ..................................................... 32
Mantel Clearances ......................................................... 33
Firebrick Installation Instructions ................................... 34
Replacement Parts ........................................................ 35
Craftsman Surround Installation .................................... 36
Clearances ............................................................ 36
Craftsman Fireplace Clearances (Figure 38)........... 36
Fireplace Installation into the Chase....................... 38
Removing the Upper and Lower Grill assemblies:.. 38
Mounting the Side Brackets.................................... 38
Attaching the front wall Board. .............................. 39
Chase Inlet ............................................................ 40
Installing the Top Brow Mount and Upper Grill....... 41
Attaching the lower grill ......................................... 42
Decorative Finish On The Front ............................ 43
Raised Hearth ......................................................... 43
Installing The Front ................................................ 44
Parts ...................................................................... 45
Rating Label .................................................................. 46
Table of Contents
2100000811_200418-48
FP30 Series B

PLEASE SAVE THESE INSTRUCTIONS
This manual describes the installation and operation of the Pacic Energy, FP30 and FP30AR Zero Clearance Wood
Fireplace.
This heater meets the 2015 U.S. Environmental Protection Agency's crib wood emission limits for wood heaters sold
after May 15, 2015. Model FP30 Series B: 2.5 g/hr.
Under specic test conditions this heater has been shown to deliver heat at rates ranging from 14,600 to 38,600 Btu/hr.
SAFETY NOTICE: If this heater is not properly installed, a house re may result. For your safety, follow the installation
instructions. Contact local building or re ofcials about restrictions and installation inspection requirements in you area.
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result
in property damage, bodily injury, or even death.
Experience will give you the right settings for proper combustion and efcient burning. Remember the correct air inlet
setting is affected by variables such as type of wood, outside temperature, chimney size and weather conditions. With
practice, you will become procient in operating your heater and will obtain the performance for which it was designed.
EPA Certied Emissions 2.5 grams per hour
LHV Tested Efciency 1 76.8%
HHV Tested Efciency 2 63% (EPA Default)
EPA BTU Output 3 14,600 to 38,600 Btu/hr
Peak BTU/Hr Output 4 99,000 Btu/hr.
Maximum Wood Length 20 inches
Ideal Wood Length 18 inches
Fuel Seasoned Cord wood
1 Weighted Average Lower Heating Value (LHV) efciency as
tested using CSA B415 Performance testing of solid-fuel-
burning heating appliances. LHV assumes the moisture is
already in a vapour state so there is no loss of energy
2 Weighted Average Higher Heating Value (HHV) efciency
as tested using CSA B415 Performance testing of solid-fuel-
burning heating appliances. HHV includes the energy required
to vaporize the water in the fuel
3 The range of BTU outputs is based on efciency using CSA
B415 Performance testing of solid-fuel-burning heating appli-
ances and burn rates from the low and high EPA tests using
Douglas Fir dimensional lumber.
4 The Peak BTU/hr is based on efciency using CSA B415
Performance testing of solid-fuel-burning heating appliances,
the Maximum one hour High burn rate from the High Burn EPA
test and the BTU content of cord wood (8600 btu/lb).
Efficiency and BTU Output
3
100000811_200418-48 FP30 Series B

Safety and Maintenance
NOTE: WE STRONGLY RECOMMEND THAT SMOKE AND CARBON MONOXIDE DETECTORS BE
INSTALLED IN THE AREA WHERE THE HEATER IS TO BE INSTALLED.
If smoke detectors have been previously installed, you may notice that they are operating more frequently.
This may be due to curing of stove paint or fumes caused by accidentally leaving the re door open. Do not
disconnect the detectors.
1. Burn only, dry and well seasoned cord wood. The denser or heavier the wood when dry, the greater its
heat value. This is why hardwoods are generally preferred. Green or wet wood should not be used, it will
reduce heat output, as well as, contribute signicantly to creosote buildup.
WARNING: NEVER USE CHEMICALS OR ANY OTHER VOLATILE LIQUID TO START A FIRE. DO
NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA, OR ENGINE OIL.
WE STRONGLY RECOMMEND THAT SMOKE DETECTORS BE INSTALLED.
WARNING: This unit is not designed to be operated with the ring door open. In addition to the obvious
hazard of sparks landing on combustibles, an open re door will cause the heater to draw excess air from
the living space and possibly cause suffocation.
2. Remove ashes frequently. Embers can roll out the door and create a re hazard. Maintain a 1”(25mm)
minimum ash base.
3. The area where boost combustion air enters the rebox must be kept clear of excessive ash buildup
which will block air ow. This area is at the inside front of the rebox.
4. If glass becomes darkened through slow burning or poor wood, it can be cleaned with replace glass
cleaner when the replace is cold. Never scrape with an object that might scratch the glass. The type and
amount of deposit on the glass is a good indication of the ue pipe and chimney buildup. A light brown
dusty deposit that is easily wiped off usually indicates good combustion and dry, well-seasoned wood and
therefore relatively clean pipes and chimney. On the other hand, a black greasy deposit that is difcult to
remove is a result of wet and green wood and too slow a burning rate. This heavy deposit is building up as
quickly in the chimney.
5. Establish a routine for the fuel, wood burning and ring technique. Check daily for creosote buildup until
experience shows how often you need to clean to be safe.WARNING: ONLY USE MATERIALS AND
COMPONENTS SUPPLIED OR SPECIFIED BY THE MANUFACTURER WHEN DOING MAINTENANCE
OR REPLACEMENTS. DO NOT USE A FIREPLACE INSERT OR OTHER PRODUCTS NOT SPECIFIED
FOR USE WITH THIS FIREPLACE.
6. DOOR GASKETS - The gasket used by Pacic Energy (7/8”(22mm) high density breglass rope) requires
only light pressure to seal. This will prolong seal life. It is important that the door seal be maintained in
good condition. Periodically inspect seals and replace if necessary.
7. DOOR GLASS - Replacement glass can be obtained from your dealer.
Use 21-5/8” (550mm) x 11-3/8” (290mm) x 5 mm ceramic glass only.
WARNING: DO NOT SUBSTITUTE CERAMIC GLASS WITH ANY OTHER TYPE OF MATERIAL.
USE ONLY CERAMIC GLASS
4100000811_200418-48
FP30 Series B

WARNING: DO NOT SLAM LOADING DOOR OR OTHERWISE IMPACT GLASS. WHEN
CLOSING DOOR, MAKE SURE THAT NO LOGS PROTRUDE TO IMPACT THE GLASS. IF
THE GLASS GETS CRACKED OR BROKEN, IT MUST BE REPLACED BEFORE USING THE
FIREPLACE.
WARNING: OVER FIRING THE APPLIANCE WILL SHORTEN THE LIFE OF THE PRODUCT.
FAILURE TO RECTIFY AN OVER FIRING CONDITION CAN BE HAZARDOUS AND MAY VOID
THE MANUFACTURER’S WARRANTY.
To remove broken glass,remove the door gasket and clean out the screw heads. Remove the screws that
hold the retainer and remove the retainer, noting position for reassembly. Remove all particles of glass. Be
careful as they are very sharp. Install new glass complete with gasket. Replace retainers, screws and re-install
the gasket using gasket cement.
CAUTION:
DO NOT OVERTIGHTEN, TIGHTEN SCREWS HAND TIGHT
DO NOT CLEAN GLASS WHEN HOT
DO NOT USE ABRASIVE CLEANERS ON GLASS
8. Do not store wood within heater installation clearances, or within the space required for fuel loading and
ash removal. Keep the area around the heater clean and free of loose combustibles, furniture, newspa-
pers, etc.
9. Instruct all members of your family on the safe operation of the heater. Ensure they have enough knowl-
edge of the entire system if they are expected to operate it. Stress the section on chimney res and the
importance of following the steps outlined, see "In the event of a Chimney Fire" on page 8
10. Inspect and clean your chimney system at the beginning of the burning season before your rst re and at
least every two months during the burning season. Inspect the interior and exterior of the pipe for defects
and/or damage. Remove and inspect the rain cap. Refer to the chimney system manufacturer’s installation
instructions for the procedure to remove and or replace any necessary components to the chimney sys-
tem.
11. Maintain a distance of 48”(1.2m) from the door to all combustible materials (i.e. furniture, drapes etc.) in
the room.
See "Ember Protector" on page 31 for Ember Protection dimensions.
5
100000811_200418-48 FP30 Series B

Maintenance Checks
Check the following parts for damage such as cracks, excessive corrosion, burned out sections and exces-
sive warping: (See website for descriptions and more detail).
Weekly:
• Firebrick - Visual, for cracking.
• Door Gasket - sagging, placement, damage.
Monthly
• Brick rail tabs and brick rails.
• Air riser tube in the back of the rebox.
• Back side of airwash chamber.
• Bafe locking pin.
• Boost manifold cover.
When Cleaning the Chimney System:
• Top bafe board/blanket.
• Bafe.
• Top heat shield and mounting bolt.
• Bafe Gasket.
• Brick Rails.
• Manifold.
Baffle:
• Some warping of the bafe is normal (up to 1/4” or 7mm).
• Replace if the bafe has permanent warping greater than 1/4" (7mm) or shows signs of cracking or
breakage.
• Please contact your Dealer if you experience any of the damage listed above. Continuing to operate your
replace with broken parts may accelerate damage to other parts and may void your warranty.
Ash Removal:
Caution: Ashes are to be removed only when the heater is cold. Whenever ashes get 3 (76mm) to 4 (102mm)
inches deep in your rebox, and when re has burned down and cooled, remove excess ashes. Leave an ash
bed approximately 1” (25 mm) deep on the rebox bottom to help maintain a hot charcoal bed.
Disposal of Ashes:
Ashes should be placed in a metal container with a tight tting lid. The closed container of ashes should be
placed outside on a non-combustible oor or on the ground, well away from all combustible materials, pend-
ing nal disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be
retained in closed container until all cinders have thoroughly cooled. Other waste should not be placed in this
container.
6100000811_200418-48
FP30 Series B

Baffle Removal
THE BAFFLE SHOULD ONLY BE REMOVED WHEN CHIMNEY IS BEING CLEANED.
DO NOT OPERATE WITH BAFFLE ASSEMBLY OR INSULATION REMOVED.
Bafe Air
Tube
Figure 1: Bafe Air Tube.
1. Remove retaining pin located just
beneath the bafe at the rear inside
top of the rebox (Figure 1).
2. Lift bafe up on one side then lift up
and remove one of the side brick rails.
Lift the bafe up and pull forward to
disconnect it from the Bafe Air Tube.
3. Slide the bafe to the side with the rail
in place, then tilt bafe sideways to
drop down and remove from rebox.
4. To re-install the bafe, perform the
removal steps in the reverse order.
Ensure that the two side pieces of
insulation are set in place against the
bafe. If the insulation is damaged
during removal, it should be replaced.
WARNING: AFTER YOU REMOVE THE BAFFLE, ALWAYS COVER THE TOP OF THE BAFFLE AIR TUBE
LOCATED IN THE REAR OF THE FIREBOX. THIS PREVENTS DEBRIS FALLING DOWN THE TUBE.
FAILURE TO DO SO WILL RESULT IN POOR OPERATION AND POSSIBLE DAMAGE TO FIREPLACE
COMPONENTS.
Secondary Air Box Cleaning
The secondary air box is located on the bottom rear of the replace and can be accessed for cleaning by
removing the small access cover located on the bottom of the rebox just in front of the Bafe Air Tube.
Access
cover
Figure 2: Secondary Airbox clean out cover.
1. Remove the two bottom center back bricks to
expose the access cover, then remove the 2
screws holding the access panel to the rebox
bottom.
2. Looking through the hole in the rebox bottom,
inspect the Airbox for debris.
3. If debris is present, carefully use a vacuum to
clean out any ash through the hole .
4. Replace the access cover, and install the bricks.
* MAKE SURE THE GASKET IS IN GOOD
CONDITION AND POSITIONED CORRECTLY.
IF IT IS DAMAGED THEN IT MUST BE
REPLACED.
7
100000811_200418-48 FP30 Series B

Chimney Smoke and Creosote Formation
Creosote - Formation and need for removal:
When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled
moisture to form creosote. The creosote vapours condense in the relatively cool chimney ue of a slow
burning re. As a result, creosote residue accumulates on the ue lining. When ignited, this creosote makes
an extremely hot re.
The chimney connector and chimney shall be inspected at least twice a year during the heating season to
determine if a creosote buildup has occurred. If creosote has accumulated it shall be removed to reduce the
risk of a chimney re.
Wet or green wood contributes signicantly to creosote formation as the excess moisture that is boiled
off, cools the re, making it difcult for the tars and gases to ignite, thus creating dense smoke and poor
combustion.
Preventing a Chimney Fire
There are three things you can do to prevent chimney res:
1. Do not let creosote build up to a point where a chimney re is possible.
2. Do not have res in the heater that may ignite chimney res. These are very hot res, such as when burn-
ing household trash, cardboard, Christmas tree limbs, or even ordinary fuel wood; (e.g.. with a full load on
a hot bed of coals and with the air control open for long period of time.)
3. Regular inspections and cleaning
In the event of a Chimney Fire
Chimney res are dangerous. Temperatures inside the chimney can exceed 2000°F (1093˚C). This causes
much higher than normal temperatures on its exterior surfaces. Thus ignition of nearby or touching combus-
tible material is more likely during a chimney re. Proper clearances are critical for safety, during such a re.
Chimney res are easy to detect; they usually involve one or more of the following:
• Flames and sparks shooting out of the top of the chimney.
• A roaring sound.
• Vibration of the chimney.
Contact your local municipal or provincial re authority for further information on how to handle a chimney
re. It is most important that you have a clearly understood plan on how to handle a chimney re.
1. Prepare to evacuate to ensure everyone’s safety. Have a well understood plan of action for evacuation.
Have a place outside where everyone is to meet.
2. Close the air control on the replace.
3. Call your local re department. Have a re extinguisher handy.
4. After the chimney re is out, the chimney must be cleaned and checked for stress and cracks** before
starting another re. Also check combustibles around the chimney and the roof. - The services of a com-
petent or certied installer, (certied by the Wood Energy Technical Training program (WETT) - in Canada,
Hearth Education Foundation (HEARTH) - in U.S.A.,) are strongly recommended..
8100000811_200418-48
FP30 Series B

Burning these materials may result in the release of toxic fumes or render the heater ineffective and cause
excessive smoke.
The prohibition against burning these materials does not prohibit the use of re starters made from paper,
cardboard, saw dust, wax and similar substances for the purpose of starting a re in an affected wood heater.
Do not burn anything but wood. Other fuels, eg. charcoal, can produce large amounts of carbon monoxide, a
tasteless, odorless gas that can kill. Under no circumstances should you attempt to barbecue in this heater.
• DO NOT STORE/PLACE WOOD WITHIN THE STOVES INSTALLATION CLEARANCES, INCLUDING IN
FRONT OF THE UNIT.
• DO NOT STORE WOOD UNDER THE UNIT
How to Test Your Wood
Add a large piece of wood to the stove when it has a good large bed of coals. It is dry if it is burning on more
than one side within one minute. It is damp if it turns black and lights within three minutes. If it sizzles, hisses
and blackens without igniting in ve minutes it is soaked and should not be burnt.
CAUTION: Never use gasoline, gasoline type lantern fuel, kerosene, charcoal lighter uid or similar liquids to
start or "freshen up" a re in this heater. Keep all such liquids well away from the heater while it is in use.
CAUTION: Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.
Your PACIFIC ENERGY wood heater is designed for many years of trouble free operation. Over ring the
appliance will shorten the life of the product. Failure to rectify an over ring condition can be hazardous and
may void the manufacturer's warranty.
Wood Selection
This heater is designed to burn natural Cordwood only. Higher efciency and lower emissions
generally result when burning air-dried seasoned woods, as compared to green or freshly cut woods.
Wood should be properly air dried (seasoned) for six months or more. Wet or undried wood will cause the re
to smoulder and produce large amounts of smoke and creosote. Wet wood also produces very little heat and
tends to go out often. Wood should be stored under cover away from open ame or heat sources.
Operation
Salt water wood * Treated wood
Wet or green wood Coal/charcoal
Garbage* Solvents*
Lawn clippings/yard waste Unseasoned wood
Railroad ties Manure or animal remains
Materials containing plastic* Materials containing asbestos
Construction or demolition debris Materials containing rubber, including tires
Paper products, cardboard, plywood, or
particleboard.
Waste petroleum products, paints or paint thinners,
or asphalt products
* These materials contain chlorides which will rapidly destroy metal surfaces and void warranty.
DO NOT BURN THESE MATERIALS
9
100000811_200418-48 FP30 Series B

Lighting a Fire
WARNING: Never use chemicals or any other volatile liquid to start a fire.
1. Adjust air control to “High” position (all the way to the left) and open door.
2. Place crumpled newspaper in the centre of the heater and crisscross with several pieces of dry kindling.
Add a few small pieces of dry wood on top.
3. Ignite the paper and leave the door ajar approximately 1/2"(13mm) - 1"(25mm) until the wood kindling is
fully engulfed in ame. ** DO NOT LEAVE THE STOVE UNATTENDED WHILE THE DOOR IS OPEN**
4. After the kindling is fully engulfed add a few small logs. Close door.
5. Begin normal operation after a good coal base exists and the wood has charred.
Normal Operation
WARNING: This wood heater has a manufacturer-set minimum low burn rate that must not be altered.
It is against federal regulations to alter this setting or otherwise operate this wood heater in a manner
inconsistent with the operating instructions in this manual.
1. Set air control to a desired setting. If smoke pours down across the glass (waterfall effect) this indicates
you have shut the control down too soon or you are using too low a setting. The wide range control makes
nding the desired setting for your application easy. As every home's heating needs vary (ie. insulation,
windows, climate, etc.) the proper setting can only be found by trial and error and should be noted for
future burns.
2. To refuel, adjust air control to “High” position(all the way to the left), and give the re time to brighten.
Open the door slowly, this will prevent backpufng or ame roll-out.
3. Use wood of different shape, diameter and length ( recommended 18"(450mm)). Load your wood and try
to place the logs so that the air can ow between them. Always use dry wood.
4. Do not load fuel to a height that exceeds 7 1/2" from the rebox oor or in such a manner that would be
hazardous when opening the door.
5. For extended or overnight burns, unsplit logs are preferred. Remember to char the wood completely on
"High" setting before adjusting air control to the "Low" setting for overnight burn.
• Highest smoke densities and emissions occur when a large amount of wood is added to a bed of hot
coals and the air inlet is closed too soon. The heated wood generates smoke, but without ample air, the
smoke cannot burn. Smoke-free, clean burning requires small fuel loads, two or three logs at a time or 1/2
of a fuel load and leaving the air inlet relatively wide open, when most of the smoke generating reactions
are occurring. After 15 to 30 minutes, the air inlet can be turned down substantially without excessive
smoke generation.
WARNING: Always keep loading door closed when burning. This heater is not designed for open door
burning.
WARNING: No alteration or modification of the combustion air control assembly is permitted. Any
tampering will void warranty and could be very hazardous.
10 100000811_200418-48
FP30 Series B

WARNING: Do not use grates or andirons to elevate the fuel. Burn directly on the fire bricks. Replace
broken or missing bricks. Failure to do so may create a hazardous condition.
Restarting After Extended or Overnight Burns
1. Open door and rake hot embers towards the front of the heater. Add a couple of dry, split logs on top of
embers, close door.
2. Adjust air control to high and in just a few minutes, logs should begin burning.
3. After wood has charred, reset air control to desired setting.
4. To achieve maximum ring rate, set control to “High” position (all the way to the left). Do not use this
setting other than for starting or preheating fresh fuel loads.
Over Firing
DO NOT OVERFIRE THIS HEATER: Attempts to achieve heat output rates that exceed heater design
specifications can result in permanent damage to the heater and chimney.
Over ring can be caused by operating the unit with the door open, too high of a chimney draft, damage to
door gaskets allowing excess air to enter the rebox, the use of kiln dried lumber, mill ends or paper waste
and prolonged or continual use on a high burn setting.
Proper Draft
Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your
chimney depends on the length of the chimney, local geography, nearby obstructions and other factors.
Too much draft may cause excessive temperatures in the appliance. An uncontrollable burn or a glowing
red stove part or chimney indicates excessive draft. Inadequate draft may cause backpufng into the room
and plugging of the chimney. Smoke leaking into the room through appliance and chimney connector joints
indicates inadequate draft.
Curing of the paint finish
See the included "Stove Bright User Guide". When burning your stove for the rst 2-3 times it is very
important that the room be well ventilated. Open all windows and doors. Smoke and fumes caused by the
curing process may cause discomfort to some individuals.
Health Warning.
The smoke from the curing process displaces oxygen. Small children, elderly and persons with existing
breathing problems should vacate the area during the hot burn to avoid the discomfort of lost oxygen. The
smoke is primarily Carbon Dioxide, and therefore non-toxic but can be uncomfortable.
Ash Removal
Caution: Whenever ashes get 3 to 4 inches deep in your rebox, and when re has burned down and cooled,
remove excess ashes. Leave an ash bed approximately 1" (25 mm) deep on the rebox bottom to help
maintain a hot charcoal bed for future res.
11
100000811_200418-48 FP30 Series B

Problem Cause Cure
Glass is Dirty 1. Wood is wet - Use dry wood
2. Turning down air control - Do not turn down until
or damper too soon a) there is a good bed of coals
b) the wood is charred
3. Draft too low - Improper chimney height and / or diameter
- Chimney plugged or restricted, check ue
- Provide outside air for combustion
4. Door gasket leakage - Replace gasket
- Check latch
Excessive Creosote Buildup - See 1, 2, 3, above.
Low Heat Output 1. Wood is wet - Use dry wood
2. Fire too small - Build a larger re
3. Draft too low - Chimney plugged or restricted, inspect
and clean
Won’t Burn Overnight 1. Air control is set too high - Set control lower
2. Not enough wood - Unsplit wood is preferred for overnight burns
3. Draft too high - Excessive chimney height and/or diameter,
See "Proper Draft" on page 11.
Stove Won’t Burn 1. Combustion air supply - Check outside air supply for obstruction
blocked - Check that room air cover is removed
2. Draft too low - Chimney plugged or restricted, inspect and
clean
- Chimney oversized or otherwise unsuitable,
consult Dealer
Troubleshooting
12 100000811_200418-48
FP30 Series B

Blower Removal
NOTE: DISCONNECT POWER BEFORE PROCEEDING
1. The blowers are located in the bottom compartment of the replace and can be accessed by removing
the access panel on the bottom of the rebox and the two-piece access panel in the airbox below that.
2. Remove the bricks to expose the access panel, then remove the 8 bolts holding the access panel using a
7/16” socket or wrench (Figure 1).
Bolts
Figure 3: Access panel bolts.
Screws
Figure 4: Thermoswitch bracket and access panel screws.
3. Loosen the two screws securing the thermo switch bracket and slide the bracket back and set aside to
clear the opening for removing the blower (Figure 4).
4. Remove the two screws securing each half of the lower access panel and lift the panel halves out through
the upper access opening.
5.
Disconnect the wire leads of the blower you are replacing from the electrical terminal block located on the
base of the unit, between the blower brackets and the connection to the Thermo Switch (Figure 5).
13
100000811_200418-48 FP30 Series B

Reverse the process to reinstall blower.
Make sure the Access Panel gasket is in good condition. Replace if needed. (pn.# 800001678 )
9. Remove the nuts attaching the blower to the
bracket and replace blower (Figure 6).
6. Remove the two wingnuts securing the
blower mounting bracket.
7. Gently lift the bracket and slide the blower
towards the front of the replace.
8. Lift the blower up and out of the replace
through he access openings.
Terminal
block
Ground
wire
Wingnuts
Figure 5: Terminal block, blower wingnuts and ground wire
Nuts
Figure 6: Blower mounting nuts
GROUND
115v from Wall Switch
or Fan Controller
NEUTRAL
BlowerBlower
Figure 7: Electrical diagram
14 100000811_200418-48
FP30 Series B

Fireplace Installation
Warning: Under no circumstances is this heater to be installed in a makeshift or "temporary" manner. It may
be red only after the following conditions have been met.
Check with your local re/building authority for any installation code requirements and restrictions in your
area.
• The services of a competent or certied installer, (certied by the Wood Energy Technical Training program
(WETT) - in Canada, Hearth Education Foundation (HEARTH) - in U.S.A.,) are strongly recommended.
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
• WARNING:DO NOT INSTALL IN A SLEEPING ROOM. (MANUFACTURED OR MOBILE HOME ONLY)
Locating your Fireplace
The best location to install your replace is determined by considering the location of windows, doors, and
the trafc ow in the room where the replace will be located. Allow space in front of the unit for the Ember
Protection and clearances to combustibles "Fireplace Clearances and Chimney Restrictions" on page 16.
Take into consideration the location of the chimney. Ideally, you should choose a location where the chimney
will pass through the house without cutting oor or roof joists.
This replace may not be installed in a factory built replace unless tested with the replace. This replace
has not been tested for installation into a factory built replace
Wind direction and magnitude can play a factor in the chimney performance. Therefore the chimney out-
let position is important when locating the replace. We recommend, whenever possible, that the chimney
should:
• Penetrate the highest part of the roof.
• Be installed as far as possible from roof offsets, trees or any other obstructions that may cause wind
turbulence or back drafts in the chimney.
• Contain the fewest number of offsets (elbows) possible.
Check the adequacy of the oor by rst estimating the weight of the replace system (approx. 500lbs(227Kg)),
plus the venting. Next measure the area the replace will occupy. Note the oor construction and consult your
local building code to determine if any additional oor support is needed. In most cases, no additional sup-
port is needed for the replace.
The replace may be installed directly on a combustible oor or on a raised base. A minimum of 84"(2.13m)
measured from the base of the appliance to the ceiling is required inside the chase and in the room. Add the
base height to all measurements if raising the unit.
Mobile Home Installation notes:
• In the USA: the unit must be installed in accoradance with the requirements of the Department of Housing
and Urban Development (HUD)"Manufactured Home Construction and Safety.
• In Canada: the unit must be installed with access openings into the built in enclosure for inspection
purposes. The access covers must require a household tool to open.
15
100000811_200418-48 FP30 Series B

Dimensions
Crate Removal
1. Carefully remove wood top and supports.
2. Remove the screws securing the replace to the pallet(4).
3. Remove from pallet bottom.
Fireplace Clearances and Chimney Restrictions Distance
Distance of combustible material from the side or back standoffs and framing kit. 0” (0,0 mm)
Minimum distance from the adjacent side wall to center line of replace. 41 1/2” (1.054m)
Minimum distance from the adjacent side wall to the side of the replace door. 30” (760mm)
Ceiling clearance - both inside the chase and in the room: from the base of the replace
to the ceiling.
84" (2.13 m)
Minimum chimney height: minimum total chimney height from replace top to below the
chimney rain cap.
15’ (4.57 m)
Recommended maximum chimney height (at sea level) from top of replace to rain cap. 35’ (10.7 m)
Maximum unsupported chimney height. 15’ (4.5 m)
Minimum depth of non-combustible ember protection: from the front of the replace. 18” (457 mm)
Minimum width of Ember protection (8"from the side of the door opening in U.S.A.)
Minimum width of Ember protection (8" from the side of the unit in Canada).
39"
58” (1.47 m)
FP30 &
FP30AR
47”
[1.19m]
34 7/8”
[886mm]
9 5/8”
[245mm]
30 3/4”
[781mm]
42”
[1.07m]
30 1/8”
[765mm]
13 1/4”
[337mm]
28 1/2”
[724mm]
24”
[610mm]
Required framing kit is not shown in this diagram
56”
[1.42m]
1”
[25mm]
Figure 8: FP30 & FP 30 Arch Dimensions
16 100000811_200418-48
FP30 Series B

Minimum Framing Dimensions
The top front framing must be built
as shown, (Figure 10) with no wood
framing directly in front of the chimney
system
WARNING: The replace must not be
in contact with any insulation or loose
lling material. If you are insulating the
chase, cover the insulation with drywall
or non-combustible panels. Maintain all
proper clearances.
WARNING: Drywall materials are
considered combustible and theIr
thickness must be accounted for in
your framing dimensions.
The open volume inside the chase is
required for heat management. Do Not
build a recess, shelves or cupboards
in the area above this replace. Do
not build or place anything inside this
Minimum chase area.
Do Not insulate the front portion of the
chase above the unit.
The Steel Stud framing kit must be
used for installing this Fireplace.
24”
610mm
73”
1.85m
1”(25mm)
DISTANCE FROM BACK OF UNIT
TO REAR WALL
35 5/8”
905mm
56 1/2”
1.44m
25 1/4”
641mm
5 3/8”
137mm
73”
1.85m
56 1/2”
1.44m
16” [406mm]
103 1/4”
2.62m
8” [203mm]
NOTE: The framing dimensions shown are the
minimum to combustibeles. Framing dimensions
will need to be enlarged accordingly to accept
drywall/wallboard if used inside enclosure.
Figure 9: FP30 Framing dimensions.
24”
[610mm]
56 1/2”
[1.435m]
63 5/8”
[1.62m]
7’
[2.134m]
Minimum,
Inside enclosure,
from base of the
unit.
18”
[455mm] 18”
[455mm]
Figure 10: FP30 framing enclosure.
17
100000811_200418-48 FP30 Series B

Item Part # Description Qty.
1 5049.9912 SCREW, TEKS
#8 x 1/2”(13mm)
Pkg 40
2 7746 STUD, TOP/BOTTOM
56”(1.42m)L
2
3 9093.22 STUD, CNTR
SUPPORT SIDES,
15”(381mm)L
5
4 7747 FRAMING KIT LEG 3
1/2"(89mm)L
3
Framing Kit Installation
Each Kit Contains:
Assembly
• Lay out top/bottom studs (#2) and center studs (#3) on
their sides on a large at surface.
• Using the screws provided (1), attach the framing kit
legs(4) to the bottom stud (2).
• Next, attach each center support(3) to the bottom stud(2)
and then attach the top stud(2) to the center supports(3).
Installing the unit into the chase
• Push the Fireplace into place
(Casing must be ush with the
framing in the front) and secure as
required by local code.
• Place the Steel Framing Kit on
top of the unit with the legs down
(Figure 12). The front edge of the
framing must be ush with the
Fireplace front. Install the screws
through the outer Framing kit legs
into the replace using the holes
provided.
• Align the replace/steel framing
ush with the chase. It is very
important to provide a at surface
to attach the outer non-combustible
board to.
• Attach the Framing kit securely
to the chase's framing using
appropriate fasteners.
2
4
1
3
Figure 11: Framing kit parts.
Figure 12: FP30 Framing with Unit.
18 100000811_200418-48
FP30 Series B

This appliance must be installed with a listed 6"(150mm) chimney system approved under the following stan-
dards: CAN-ULC S629(IN CANADA) OR UL 103HT(IN U.S.).
MAINTAIN CLEARANCES TO COMBUSTIBLES AS SPECIFIED IN THE CHIMNEY MANUFACTURERS
INSTALLATION INSTRUCTIONS. YOU MUST FOLLOW THE CHIMNEY MANUFACTURER'S
INSTALLATION INSTRUCTIONS FOR INSTALLATION OF ALL CHIMNEY COMPONENTS.
USE APPROPRIATE SUPPORTS, CAPS, FLASHING AND SHIELDS IN ACCORDANCE WITH THE
CHIMNEY MANUFACTURERS INSTALLATION INSTRUCTIONS.
CAUTION: THE STRUCTURAL INTEGRITY OF THE FLOOR, WALL AND CEILING/ROOF MUST BE
MAINTAINED.
NOTE: FOR ALL CHIMNEYS, YOU MUST USE THE MANUFACTURER'S FIREPLACE ANCHOR PLATE. -
Some brands of Anchor Plate including ICC, may not sit ush with the top of the Fireplace and will require the
installation of an Anchor Plate spacer. Part #FP30.7757. Ensure the Chimney Achor plate is fully engaged with
the Fireplace's Flue Collar when using the Anchor Plate Spacer.
NOTE: The FP30 must be installed so the outlet of the
chimney system is a minimum 15ft (4.6m) in height as
measured from the base of the unit, up to a maximum
height of 35' (10.7m). The chimney must be supported on
lengths over 15' (4.5m).
NOTE:
Install all components following the chimney
manufacturer's installation requirements/instructions.
Consult your chimney supplier for installation advice.
1. After locating the desired location and framing in the
replace, use a plumb bob to line up the holes with the
Flue Collar. Cut and frame square holes in all oors,
ceilings, and roof that the chimney will pass through.
Mount the chimney manufacturer's restops and radiation
shields to the framing as per their instructions.
WARNING: A radiation shield/firestop must be used for
each floor/wall the chimney passes through.
2. Maintain the chimney manufacturers minimum clearance
between the chimney and any combustible materials. Do
not ll the space with insulation or any other combustible
material. Install the insulation shields as required by
code and all pieces necessary to prevent contact with
combustible materials whenever passing through oors,
ceilings or attic spaces.
Chimney Installation
Anchor
Plate
Listed
Chimney and
Accesories
Maintain
37” [94cm]
Minimum distance
from the top of the
unit to the ceiling.
Non-Combustible
Ember Protection
Minimum distance
from the base of the
unit to the ceiling is
7’ [2.13m]
Insulation Shield
Firestop
Figure 13: FP30 Basic installation.
19
100000811_200418-48 FP30 Series B

3. Install the pipe manufacturer's replace anchor/base plate by inserting it into the ue collar on the
replace. We recommend sealing the joint with stove cement. Secure the anchor plate with stainless steel
screws. If the Anchor Plate will not sit ush on top of the unit, a Pacic Energy "Anchor Plate Spacer"
should be used beween the replace and the Anchor Plate. This is due to diferences in the manufacturers
chimney sizes.
4. Assemble the chimney sections so the nished length is resting on the manufacturer's anchor plate and
protruding through the roof. Avoid having joints between the ceiling and the roof. It is required that the
chimney connections be secured with three (3) #8x½"(12 mm) stainless screws.
5. As per the vent manufacturers instructions, Install the Roof Radiation Shield, Flashing and Storm Collar.
Be sure to maintain the vapour barrier at this point. (Seal securely.)
6. Install any exterior venting - If the chimney extends more than 5'(1.5m) above the point of contact with the
roof, then it must be secured using roof braces
7. Securely attach the rain cap and check the ashing for leaks.
Minimum
36”(915mm)
length of Chimney
before rst elbow
Maintain
Chimney
manufacturer’s
clearances
Maximum
48” (1.22m)
total length of
Offset
chimney
Figure 14: FP Offset Installation.
Offset Chimney:
The chimney for the FP30 can be installed with a maximum
of four 45° elbows(in Canada) or four 30° elbows(in U.S.A.)
as shown in Figure 143.
Follow the chimney manufacturer's guidelines for support-
ing the offsets. Reminder - The chimney must be supported
after the rst 15' (4.5m) in length.
1. NOTE: Install the vertical chimney section(s) then the
rst elbow and turn it in the required direction.
2. Install the necessary chimney lengths (to a maximum
of 4ft. (1.22m)) to achieve the required offset. Lock the
chimney lengths together according to the chimney
manufacturer’s instructions.
3. Follow the chimney manufacturers' requirements for the
use an offset or roof support halfway on the offset. If
penetrating a wall, install a wall radiation shield supplied
by the chimney manufacturer and install according to
the manufacturer's instructions.
4. Use another elbow to turn the chimney vertical and
secure the elbow.
5. Continue Installing the chimney following the chimney
manufacturer's directions including all restops shields
and ashings.
20 100000811_200418-48
FP30 Series B