Pacific PR836AS Installation guide

XP022396(1)
抽油煙機使用說明書
型號:PR830AS / PR836AS
抽油機型號:
序 號:
XP022396(1)
Use,Care,and lnstallation Guide
Model:PR830AS / PR836AS
Model number:
Serial Number:

Table of Content
I. Product Functions/Performance Specification Chart .. . 1
II.
Parts Instructions ................................................…. . 2
III. Installation Guidelines …………………………………. . 3
IV. Installation Procedures …………………………..……. . 4
V. Venting Instruction…………………………………...… . 5
VI.
Installation Air outlet ………………………………….. . 6~7
VII. Operating Instructions ……………………………..….. . 8
VIII. Replacing Light Bulb ……………………………..…… . 9
IX. Surface Maintenance …………………………………. . 10
X. Troubleshooting …………………………………………. . 11
目錄
一.功能簡介/性能規格表………………………. . 1
二.配件說明………………………………………. 2
三.安裝原則………………………………………. 3
四.安裝步驟………………………………………. 4
五.安裝排風管 …………………………………... 5
六.安裝出風口……………………………………. 6~7
七.按鍵說明………………………………………. 8
八.移除燈泡………………………………………. 9
九.機身表面保養和清潔 ………………………….. 10
十.排除故障………………………………………. 11

1. 1.
一.功能簡介/性能規格表
PR836AS
44磅
120V – 60Hz
圓型 6吋,方型 3-1/4"x10" 吋
36”X22.5”X8”
PR830AS PR836ASPR830AS
40.7磅
120V – 60Hz
圓型 6吋,方型3-1/4"x10"吋
2A/225W 2A/225W 2A/225W 2A/225W
鹵素燈 35Wx2 鹵素燈 35Wx2
30”X22.5”X8”
1. 3速風速選擇。
2. 可控制燈的開/關，具亮、暗二段調整。
A.功能簡介
B.性能規格表
淨 重 (英磅)
型 號
尺 寸(英吋)
最大伏特數
風管直徑
燈 泡
最大消耗功率
I. Product Functions/Performance Specification Chart
A. Product Functions
1. 3-speed options.
2. Light has varying degrees of brightness: Bright, Dim and Off.
B. Specification Chart
Net weight(Pound)
Models
Measurement (inches)
Maximum Voltage
Exhaust Pipe Diameter
Light
Maximum consumption
power
120V – 60Hz
Round 6 inches
Square 3-1/4"x10" inches
Round 6 inches
Square 3-1/4"x10" inches
Halogen light 35Wx2 Halogen light 35Wx2
120V – 60Hz
30”X22.5”X8” 36”X22.5”X8”
44 lbs40.7 lbs

PR830AS / PR836AS
II. Parts Instructions
二.配件說明
2. 2.
種類 數量
螺絲包配件:
序號
P3螺母
5 x 24m/m 華司
M6 x 1-1/2吋木螺絲
M6 x 1吋木螺絲
M6 x 2吋木螺絲
3/16 x 1/2 平頭田丸十字螺絲
吊掛組
3
4
4
4
4
1
2
4
A
F
C
B
D
E
H
G
鹵素燈拆裝吸盤
DESCRIPTION N°
HARDWARE PACKAGE CONTENTS
TYPE
Wire Nuts
5 x 24m/m
Washers
M6 x 1-1/2” wood screws
M6 x 1” wood screws
M6 x 2” wood screws
3/16 x 1/2
screws
Wall bracket
3
4
4
4
4
1
2
4
A
F
C
B
D
E
H
G
Halogen light Suction Cup
4
5
3
8
10
11
12
13
7
1
6
9
2
PR830AS / PR836AS
4
5
3
8
10
11
12
13
7
1
6
9
2
半圓鐵片
6"圓型鐵片
活葉轉軸組
機箱
風胃
飾板
濾網彈片
燈飾板組
鹵素燈
馬達旋鈕開關
旋鈕開關
油杯座
不鏽鋼濾網組
Shell
3-1/4"x10"
rectangular collar
6" round vertical
transition adapter
6" round vertical transition
adapter with rectangular
transition adapter
Blower housing
Grease Tray
Baffle filter
Side panel
Halogen Light
Switch
Knob
Light panel
Spring

3. 3.
III. Installation Guidelines
Notice the surrounding of cooker hood. If there
are too many windows or a door nearby, it is
advisable to close the windows and door before
switching on the cooker hood to prevent the
external air current from affecting the suction.
The smoke has to rise up to 10inches from the
stove/grate to be within the range of suction
efficiency.
The ideal installation height is a distance of
26 to 36inches from the bottom of the hood to
the surface of the stove top.
The front, back, right and left of hood must be
in parallel and horizontal level, to avoid the oil
in the oil tub from spilling over. To ensure that
the hood is leveled when installing, it can be
measured by the hook mark for the left and right
side; and the screws fixed securely onto the wall
to ensure the front and back of the hood are parallel.
ln order to increase the efficiency of hood efficiency of hood,
recommending using the provided 6 inch duct to maintain maximum
air flow efficiency; the length of duct must to be minimized.
Please do not arrange the hood socket with the other high electricity
consumption appliances.
Too many windows, too much
air current.
Pic. 1
Pic. 2
Pic. 3
1. Surrounding Environment (Pic.1)
2. Installation Heights (Pic.2)
3. Hood installed in parallel and horizontal level
(Pic.3)
4. Exhaust duct
5. Socket arrangement
26~36 in
三.安裝原則
抽油煙機安裝位置，如在窗上 或附近有太多門窗，
請在開動抽油煙機前，先關閉門窗，以免空氣對流
大而影嚮吸力，因當油煙上昇未至10吋之有效吸力
範圍，則無法充分發揮抽油煙最佳效果。
1. 周圍環境(圖一) :
(圖一)
(圖二)
(圖三)
門窗太多、對流太大
安裝高度自本機底板至煮食爐面之距離以26~36吋
為最理想。
2. 安裝高度(圖二) :
機體應保持前、後、左、右水平，以免氣流箱，導油
盆積油而溢出。
左、右水平可由掛碼調整，前、後水平則由鋼丁螺
絲鎖緊牆壁，以固定標準。
3. 機體應保持水平(圖三):
4. 排風管:
5. 插座安排:
為增加吸力效能，請配合使用本機出風管接頭之直
徑6吋排風管，排風管長度應以適合長度最佳，不宜
過長。
請勿與烤箱或冰箱等耗電量較高之電器產品共用一個插座。
26~36 in
2-4

4.
風管膠帶
四.安裝步驟
1.請準備安裝位置及空間。
2.測量出風口及電源線孔的大小，然
後再鑽孔。
3.櫥櫃需加強本機固定的地方，建議
使用木條強化在櫥櫃內底部。
4.請先卸下不鏽鋼濾網，再用十字起
子移除兩側修飾板，並取下不鏽鋼
油杯。
5.依安裝位置設置四支木螺釘。
6.安裝時用木螺釘扣上之後，將油機
與櫥櫃用螺絲鎖緊，讓油機與櫥櫃
安全不會掉落。
7.裝設電源。
8.安裝風管並用風管膠帶密封。
9.檢查風管處是否緊密及其他功能是
否正常。
10.依序將不鏽鋼油杯、修飾板及不鏽
鋼濾網重新安裝回去。
櫥櫃安裝說明:(如圖一)
不鏽鋼濾網
與修飾板
油杯
圖一
電源線孔
木條
木螺釘與鑰匙孔
風管圈孔
IV. Installation Procedures
Hood is designed for installation under a kitchen cabinet.
See Fig.1 for details.
1. Prepare duct location on hood(vertical or
horizontal) .
7. Install electrical.
8. Install ductwork and seal with aluminum duct tape.
10. Reinstall grease tray., side panels and baffle filters.
9. Power up hood and check for leaks around duct tape and test all functions.
3. Reinforce cabinet bottom with wood stips
if additional strengthening is required or if
cabinets are framed.
4. Remove baffle filters from hood.
Also remove side panels from hood using
a Phillips screwdriver to remove each of
the screws. And then remove the grease tray.
5. Use 4 wooden screws to secure the hood
to the bottom of the cabinet.
6. Lift hood onto screws located on cabinet
bottom and lock into place. Make sure all
(4) key-holes cover the screws. Tighten
each screw to secure hood to cabinet.
2. Measure and cut out duct and electrical
openings in cabinet or wall to match up
with the hood. Make sure duct opening is
large enough to apply aluminum duct tape.
4.
baffle filters&
side panels
grease tray
duct tape
Fig 1
ductwork
electrical
wood blocking
installation screws
and key-holes

V. Venting Instruction
side wall cap
w/gravity damper
cabinet
soffit or crawl space
side wall cap
w/gravity damper
roof pitch w/
flashing & cap
WARNING FIRE HAZARD
Some Ducting Options
NEVER exhaust air or terminate duct work into spaces between walls,
crawl spaces, ceiling, attics or garages. All exhaust must be ducted to
the outside. Use metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints
with certified Silver Tape or Duct Tape.
5 . 5.
五.安裝排風管
用重力阻尼器
加蓋於側牆面
櫥櫃
依梁柱底面或櫥櫃空間爬行
用重力阻尼器
加蓋於側牆面
屋面坡度可以用遮雨罩或其他遮罩加蓋
櫥櫃安裝注意事項:
安裝之風管、牆壁、櫥櫃空間、天花板或車庫與閣樓之間的空間都要
有所保留。風管只能使用金屬材質。
安裝之連接處的金屬螺絲要鎖緊，接頭處要用有認證的銀膠帶或風管
膠帶貼緊。
風管安裝選項:
Rear Ducting
背面排風

6. 6.
VI. Installation Air outlet
By default the PR830/836AS is pre-configured for 6" round vertical ducting.
1. Using a Philips-head screwdriver remove
the screws and 6" round vertical transition
adapter from top of hood body.
2.Replace 6" round vertical transition
adapter with rectangular transition adapter.
Do not secure to hood body yet.
3. Place 3-1/4"x10" rectangular collar on
top of rectangular transition adapter.
Secure rectangular adapter and rectangular
collar to hood body using the previously
removed screws from step 1.
3-1/4"x10" Rectangular Vertical Ducting
1. Using a Philips-head screwdriver remove
the screws and 6" round vertical transition
adapter from the top of the hood.
3-1/4"x10" Rectangular Horizontal Ducting
六. 安裝出風口
在預裝情況下 PR830/836AS 安裝6"圓型排風管接頭。
1. 使用十字螺絲起子，移除機體上方的螺
絲和 6"圓型排風管接頭。
1. 使用十字螺絲起子，移除機體上方的螺絲
和 6"圓型排風管接頭。
2. 使用一字型螺絲起子或斜口鉗沿著方型輪廓
線將機體後方的3-1/4"x10"方型金屬蓋移除。
3. 將3-1/4"x10"方型風管圈安裝於 6"圓型轉
方型排風管接頭上方。
使用步驟1移除螺絲，將風管圈和排風管
接頭鎖固於機體上。
2. 更換 6"圓型轉方型排風管接頭，且先不
固定於機體上。
上方排風:安裝3-1/4"x10"方型風管圈。
後方排風:安裝3-1/4"x10"方型風管圈。
2. Using a flat head screwdriver or diagonal
cutter, remove 3-1/4"x10" rectangular knock
-out cover plate from back of hood.

7 . 7.
5. Replace 6" round vertical transition
adapter with rectangular transition adapter.
Do not secure to hood body yet.
7. Place 3-1/4"x10" rectangular collar on
back of hood and secure using the screws
that previously secured the rectangular
cover plate.
6. Place 3-1/4"x10" rectangular cover plate
over the rectangular opening on top of
hood from step 3.
Secure rectangular transition adapter and
cover plate to hood body using the
previously removed screws from step 1.
3. Using a Philips-head screwdriver,
remove the screws and 3-1/4"x10"
rectangular cover plate from back of hood.
4. Remove the two plastic air diverter blocks.
The blocks are located in the hood and can
be accessed from the top when the 6" round
transition adapter is removed.
4. 取出兩個塑膠空氣導流座。
導流座位於機體內，移除機體上方6"圓
型排風管接頭後，即可從機體上方取出。
7. 將3-1/4"x10"方型風管圈置於機體後方，
並使用原本用來鎖固3-1/4"x10"方型金屬
蓋的螺絲鎖固於機體後方。
6. 將3-1/4"x10"方型金屬蓋置於步驟3的6"
圓型轉方型排風管接頭上方，並使用步
驟1移除螺絲，將風管圈和排風管接頭
鎖固於機體上。
5. 更換 6"圓型轉方型排風管接頭，但先
不固定於機體上。
3. 使用十字螺絲起子，移除機體後方3-1/4"
x10"的方型金屬蓋螺絲。

8. 8.
Rotate knob to change light settings,(1) for dim light and
(2) for bright light.
Rotate knob to change speed levels,(1) for low speed,
(2) for medium speed and,(3) for high speed.
1. Blower on/off/speed selection:
2. Lights Dim/Bright/Off:
1.馬達開關及風速調整:
以旋轉旋鈕調整風速:(1)低速 (2)中速 (3)高速。
以旋轉旋鈕調整燈光亮度:(1)微亮 (2)明亮。
2.燈光 明亮/微亮/關閉:
1 Blower on/off/speed selection
2 Lights Dim/Bright Off
1 馬達開關及風速調整
2 燈光 明亮/微亮/關閉
VII. Operating Instructions 七.按鍵說明

9. 9.
Halogen light:
When the range hood is activated or has been running for a long time,
be careful when handling the light bulb as it may be too hot to handle.
Please double check to make sure the power supply to the range hood
is shut off and the light bulb is cool before removing it.
Remove the Halogen bulb by turning it counter-clockwise to remove.
The black rubber suction tool in the installation package. provided is for
easier rewoval of the halogen light bulb.
鹵素燈移除注意：
當油煙機在運轉或經過長期運轉後請小心燈泡高溫。
請等待冷卻後再移除燈泡。
請再三確定油煙機電源關閉以及燈泡冷卻後再行移除。
請用黑色吸盤(隨機附上)，以順時針旋轉拆除，並參考以下圖示移除燈泡。
請洽經銷商購買新燈泡。
VIII. Replacing Light Bulb
八.移除燈炮

10. 10.
A. Surface Maintenance
B. Surface Cleaning and Maintenance
1. Please clean the range hood surface regularly with warm soapy
water and wipe with a cotton cloth to prevent grease from
accumulating.
2. Please do not use harsh cleansers or coarse material to clean
the surface because that will damage the surface.
3. A non-invasive stainless steel polish is recommended to polish
the surface after cleaning.
4. Please use soft material for polishing because it will make your
range hood surface shinier.
5. Please do not use cleaning solutions that have bleach as an
ingredient.
1
2
3
1.請定期以熱肥皂水和棉布擦拭機身以防油垢堆積。
2.請勿使用腐蝕性洗碗精和材質過粗的布料擦拭，以免傷害到機身表面。
3.擦拭完成後建議使用無刺激性的不鏽鋼拋光劑來進行第二次擦拭。
4.請使用軟布輕擦，您的油煙機表面將會更加光亮。
5.請勿使用含有漂白成分的清潔液。
二.保養和清潔
一.機身表面保養
1
2
3
IX. Surface Maintenance 九.機身表面保養和清潔
1.清潔前，務必要切斷電源。
2.定期清潔抽油煙機的內外側，可以保持抽油煙機壽命，
切勿使用研磨性清潔劑。
3.不鏽鋼濾網不需要換，可放入洗碗機清洗。
安裝前請擦乾。
4.建議每使用30小時後清潔一次不鏽鋼濾網，清潔完成後，必須重新裝回
原位。(見下圖拆卸說明)
5.在開啟煮食爐前，請先開啟抽油煙機以免廚房溫度太高。
1. Always disconnect from power supply before cleaning.
2. Clean both exterior and interior of the hood for long lasting.
Do not use abrasive cleanser.
3. Filter can be placed in dishwasher. Dry filtere andre-install before
using hood.
4. No need to replace stainless steel baffle regularly, they are recommended
to be cleaned every 30 hours of use, depending on cooking habit.
(See below Figure to remove filters)
5. Make a habit of turning on the hood first before turning on the
stove to avoid high temperature in the kitchen.

11. 11.
十.排除故障
Issue Cause What to do
After installation,
the unit doesn’t
work.
1. The power source is not turned
ON.
1. Make sure the circuit breaker
and the unit’s power is ON.
2. The power line and the cable
locking connector is not connecting
properly.
2. Check the power connection
with the unit is connected properly.
3. The wires on rotary switch are
loose.
3. Make sure the wires on the
switch are connected properly.
4. The switch is defective. 4. Change the switch.
Light works,but
motor is not turning.
1. The motor is defective,possible
seized.
1. Change the motor.
2. The thermally protected system
detects if the motor is too hot to
operate and shuts the motor down.
2. The motor will function properly
after the thermally protected
system cool down.
3. Damaged capacitor. 3. Change the capacitor.
4. The motor wire is not connected. 4. Make sure the motor wire is
plugged into the molex connector.
The unit is vibrating. 1. The motor is not secure in place. 1. Tighten the motor in place.
2. Damaged blower wheel. 2. Change the blower wheel.
3. The hood is not secured in place. 3. Check the installation of the
hood.
The motor is
working,but the
lights are not.
1. Defective halogen bulb. 1. Change the halogen bulb.
2. The light bulb is loose. 2. Tighten the light bulb.
3. The wires on the switch are
loose.
3. Make sure the wires on switch
are connected properly.
The hood is not
venting out properly.
1. The hood might be hanging to
high from the cook top.
1. Adjust the distance between the
cook top and the bottom of the
hood within 26” and 36” range.
2. The wind from the opened
windows or opened doors in the
surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors
to eliminate the outside wind flow.
3. Blockage in the duct opening or
duct work.
3.
Remove all the blocking from the
duct work or duct opening.
4. The direction of duct opening is
against the wind.
4. Adjust the duct opening
direction.
5. Using the wrong size of ducting. 5. Change the ducting to correct
size.
Metal filter is
vibrating.
1. Metal filter is loose. 1. Change the metal filter.
2. Spring clip is broken. 2. Change the spring clip.
異常狀況 原因 處理方式
安裝後電機不運轉 1. 無電源輸入 1. 檢查斷路器，並確認電源已接
上
2. 電源線和閉端沒有正確的安裝 2. 確認電源線和油機被正確的連
接
3. 旋鈕開關的電線鬆脫 3. 確認開關電線線被正確的連接
4. 開關有問題 4. 更換開關
燈亮但電機不運轉
1. 馬達有問題，也許卡住了
1. 更換馬達
2. 若運轉時馬達過熱將會啟動過
熱保護系統並關閉馬達
2. 待過熱保護系統冷卻後，馬達
將會再次正常運轉
3. 電容器損壞 3. 更換電容器
4. 馬達線路沒有連接 4. 確認馬達電線端子被正確地連
接
機體震動 1. 馬達不牢固 1. 檢查並鎖固馬達
2. 風葉輪損壞 2. 更換風葉輪
3. 機體懸掛不牢固 3. 檢查並校準機體
電機運轉但燈不亮
1. 燈泡損壞
1. 更換燈泡
2. 燈泡鬆脫 2. 重新旋緊燈泡
3. 開關的電線鬆脫 3. 檢查電線正常的連接
油機沒有正常排煙 1. 機體與爐面距離太大 1. 重新調整抽油煙機的高度，建
議油煙機與爐面的距離在 26”到
36”範圍之間
2. 機體周圍門窗太多，空氣對流
太大
2. 適度關閉門窗
3. 出風口或排氣管被阻塞
3. 清理阻塞物
4. 出風口逆風現象(倒灌風) 4. 調整出風口的方向
5. 排風管尺寸錯誤 5. 更換正確的排風管尺寸
金屬濾網震動 1. 金屬濾網鬆脫 1. 更換金屬濾網
2. 彈片損壞 2. 更換彈片
X. Troubleshooting