PAG CPS100 User manual

PAG CPS100
Camera Power Supply
Models 9750 & 9750V
IMPORTANT SAFETY INSTRUCTIONS
This leaflet contains important safety and
operating instructions. Read these fully and
note all warnings before using the PAG
CPS100 Camera Power Supply. Please follow
all instructions and retain this leaflet for
future reference.
The PAG CPS100 is not intended for any use
other than the powering of video cameras as
detailed in ‘Specification’.
IMPORTANT: This equipment must be grounded.
Do not connect to non-grounded supplies.
Use only on AC supplies 100-250V, 50/60Hz.
Supply connection to the unit should be
made using only the standard lead supplied
with this equipment. Do not defeat the
safety purpose of the grounding-type plug.
The grounding-type plug has two blades and
a third grounding prong. The third prong is
provided for your safety. When the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on
or pinched, particularly at plugs. Unplug this
apparatus during lightning storms or when
unused for long periods of time.
Ensure that the cooling vents are not
obstructed when in use - e.g. do not cover
them with tape or labels.
WARNING: Indoor use only. To reduce the risk
of fire or electric shock, do not expose this
apparatus to rain or moisture.
Do not disassemble the unit. There are no
user-serviceable parts inside. Incorrect
reassembly may result in a safety hazard.
Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as supply cord or plug is damaged, liquid has
been spilled, the apparatus has been exposed
to rain or moisture, does not operate nor-
mally, or has been dropped. In this event you
should seek advice from your nearest PAG
Dealer or direct from PAG Ltd. by telephoning
[phone].
SPECIFICATION
Description:
Model 9750 PAG CPS100 Camera Power Supply
(PAGlok compatible version).
Model 9750V PAG CPS100 Camera Power
Supply (V-Mount compatible version).
Input Supply: 90-264V ~ auto-selected.
Frequency 47-63Hz. Maximum power con-
sumption 175W.
Output: 15V DC, 105W nominal. The unit is
protected against over-current and short
circuit. The output is protected against over-
temperature and over-voltage by means of
a latching shutdown circuit.
PAG Ltd.
565 Kingston Road
Raynes Park
London SW20 8SA
E[email protected]
T+44 (0) 20 8543 3131
F+44 (0) 20 8540 4116
www.paguk.com

A parallel, auxilliary XLR4 output is included
for powering camera accessories. Pin 1
negative, pin 4 positive.
Two standard USB outputs are provided,
ideal for charging a smartphone. Output: 5W
at 5V total.
Safety: Designed to comply with electrical
safety standards EN60590 Class 2 (double
insulated). UK mains lead fitted with 1" fuse
to BS1362 rated 5A.
Operating Temperature Range:
0°C to +40°C (+32°F to +104°F).
Overall Dimensions (excluding PAGlok claws):
125mm wide x 175mm high x 53mm deep.
Weight: 0.7kg
OPERATING INSTRUCTIONS
PAG CPS100 Camera Power Supply Model 9750
is designed to mount directly to equipment
that is fitted with a PAGlok battery connector.
PAG CPS100 Camera Power Supply Model
9750V is designed to mount directly to
equipment that is fitted with a V-Mount
battery connector.
Fit the Power Supply to the equipment and
connect the supply cord to the input socket.
Power up the unit and the green ‘Power’
indicator LED will be lit.
The Power Supply has a nominal continuous
output of 105W at 15V, which is sufficient to
power most popular models of camera.
Ensure that the combined wattage of the
camera/recorder and a camera light (if used)
does not exceed 100W. A short duration surge
of 150W is permitted.
U5126 ISS A / JULY 2012
Do not obstruct the cooling vents that are
present on the rear of the unit.
If the Power Supply becomes overheated,
the red ‘Overheat’ LED will illuminate, the
unit will shut down, and no damage will
occur. The protection circuit will latch off,
and can only be reset by turning off the
input supply. Allow the unit to cool before
continuing to operate.
The output is protected against over-voltage.
If the Power Supply produces an excessively
high voltage it will shut down and the circuit
will latch off as described above.
SERVICING AND REPAIRS
WARNING: To reduce the risk of electric
shock, do not attempt any servicing or
repairs unless you are qualified to do so.
Refer all servicing or repairs to qualified
servicing personnel.
The Power Supply contains advanced elec-
tronics that do not require periodic mainte-
nance. Consequently there are no user
serviceable parts inside.
Qualified electronics engineers who wish to
gain access to internal assemblies should
note that parts of the power circuit retain a
high voltage even after the supply has been
disconnected. Wait for a period of five
minutes following disconnection before
commencing disassembly.
When the Power Supply is correctly connected
to an AC supply and the green ‘Power’ LED is
not lit, it is likely that a fault has developed.
Seek advice from your nearest PAG Dealer or
direct from PAG Ltd. London, by telephoning
[phone].