Pakedge Device & Software wap-c3n User guide

WAP-C3N
Enterprise-Class, Ultra High Throughput In-Ceiling
Wireless-N Access Point and Client Bridge
QUICK START
Installation Quick Guide – Version 1.0

A. WAP-C3N Default Settings
1. Wireless Access Point mode
2. IP Address for Access Point Mode-192.168.1.250
3. Username/Password- pakedge/pakedgea
4. SSID- Pakedge1
5. Power Output- High
6. Security- Disabled
B. Hardware Installation
(NOTE: The installation steps listed below are highly
abridged. For a complete, detailed list of instructions, please
refer to the WAP-C3G User Manual.)
1. Find an appropriate in-ceiling/wall location in which
to mount the unit. Use the cutout template to trace a
cutout line. Cut along the line to create the mounting hole
and place the unit in the ceiling/wall.
1
WAP-C3N INSTALLATION QUICK GUIDE

2
WAP-C3N INSTALLATION QUICK GUIDE
2. To open cover, first slide the latch outward to disengage the
tab and second, push in the cover on the red dot (outer edge
of cover, directly opposite of the latch).
3. Use a Phillips screw
driver to engage the mounting-ears as shown in a
clockwise rotation until the screws are difficult to rotate.
NOTE: Do not over-tighten the mounting-ears as excessive
torque will strip the mounting-ears and render them non-
functional.
4. Connect the cat5e/6 cable to the Power-
over-Ethernet port (PWR+LAN IN) of the
WAP-C3G and route the cable as shown.
NOTE: If the cable is not routed in this
fashion, the cable could be damaged and the
unit may not function properly.
Push
Here

3
WAP-C3N INSTALLATION QUICK GUIDE
5. Plug the other end of the Ethernet cable into a PoE injector or PoE Switch (see PoE injector
manual for completing the wiring at the PoE injector location). NOTE: Do not use a DC
power supply as the housing was not designed to accommodate POE. The diagram below
depicts the configuration using a PoE Injector.
The Wireless Access Point should now be up and running with its default out-of-the-box
setting. It does not need any particular configuration to be functional. The Wireless Access
Point can be configured through its website. To access the WAP-C3N website, you will need
an Ethernet adapter and a web browser such as Internet Explorer.
Access Point Mode Laptop
CAT 5e/6 Cable
(Data+Power)
AC Power
Cable
SW24-GB
Gigabit Switch
CAT 5e/6 Cable
(Data Only)
AC Power Cable
POE
Injector Computer
WAP-C3N

4
WAP-C3N INSTALLATION QUICK GUIDE
C. IP Address Configuration
The default IP address of the Wireless
Access Point is 192.168.1.250. In
order to log into this WAP, you must first
configure the TCP/IP settings of your PC/
Notebook.
For Windows 7:
1. In the control panel, double click
Network Connections and then double
click on the connection of your Network
Interface Card (NIC).
You will then see the this screen:
2. Select Internet Protocol Version
4 (TCP/IPv4) and then click on the
Properties button.This will allow you to
configure the TCP/IP settings of your PC/
Notebook.

5
WAP-C3N INSTALLATION QUICK GUIDE
3. Select Use the following IP Address radio button and then enter the IP address and
subnet mask. Ensure that the IP address and subnet mask are on the same subnet as the
device.
For example: Wireless Access Point
IP address: 192.168.1.250 PC IP
address: 192.168.1.10 PC subnet mask:
255.255.255.0
4. Click on the OK button to close this
window, and once again to close LAN
properties window.

D. Login/Configure the Hardware
1. To access the Wireless Access
Point’s configuration screen, enter
http://192.168.1.250 into your web browser.
2. The website of the Wireless Access Point
should appear as shown here.
E. Client Bridge, Repeater
and WDS Modes
To access the other modes, click on
Properties, under the System tab then select
the mode desired.
For further information and details beyond the
Quick Start Guide, please refer to the
User Manual on our website-
http://www.pakedge.com/usermanual.php
6
WAP-C3N INSTALLATION QUICK GUIDE

© Pakedge Device & Software Inc. 2010 – All Rights Reserved
1163 Triton Dr.
Foster City, CA 94404
USA
Visit Us At:
www.pakedge.com
F. Technical Support
Please visit our website for
up-to-date support information:
Website: www.pakedge.com
Email: [e-mail]