Panasonic CS-VE9NKE User manual

F568728
ENGLISH
Before operating the unit, read these operating
instructions thoroughly and keep them for future
reference.
FRANÇAIS
Avant d’utiliser l’appareil, lisez ce mode d’emploi
dans son intégralité et conservez-le pour toute
référence ultérieure.
ESPAÑOL
Antes de utilizar la unidad, sírvase leer
atentamente estas instrucciones de
funcionamiento y conservarlas como futuro
elemento de consulta.
DEUTSCH
Bevor Sie das Gerät in Betrieb nehmen, lesen
Sie bitte diese Bedienungsanleitung aufmerksam
durch und bewahren Sie sie für die künftige
Verwendung auf.
ITALIANO
Prima di utilizzare l’unità si prega di leggere
attentamente le istruzioni e di conservare questo
opuscolo per potervi fare riferimento in futuro.
NEDERLANDS
Lees voor u het apparaat gebruikt deze
gebruiksinstructies grondig en bewaar ze voor
toekomstig gebruik.
QUICK GUIDE
QUICK GUIDE
GUIDE RAPIDE
GUIDE RAPIDE
GUÍA RÁPIDA
GUÍA RÁPIDA
KURZANLEITUNG
KURZANLEITUNG
GUIDA RAPIDA
GUIDA RAPIDA
SNELLE GIDS
SNELLE GIDS
Operating Instructions
Air Conditioner
Model No.
Indoor Unit Outdoor Unit
CS-VE9NKE CU-VE9NKE
CS-VE12NKE CU-VE12NKE
POWER NANOE-G TIMER +8/10°C
F568728_YB0512-1062.indb 1F568728_YB0512-1062.indb 1 6/11/2012 9:43:19 AM6/11/2012 9:43:19 AM

2
ENGLISH
TABLE OF CONTENTS
TABLE OF CONTENTS
NOTICE: When the outdoor temperature is out of the above
temperature range, the heating capacity will drop significantly and
outdoor unit might stop for protection control.
OPERATION CONDITION
OPERATION CONDITION
Use this air conditioner under the following temperature range
Temperature (°C) Indoor Outdoor
*DBT *WBT *DBT *WBT
COOLING Max. 32 23 43 26
Min. 16 11 -10 -
HEATING Max. 30 - 24 18
Min. 16 - -20 -
+8/10°C
HEAT Max. 10 - - -
Min. 8 - -20 -
* DBT: Dry bulb temperature * WBT: Wet bulb temperature
SAFETY PRECAUTIONS 4~5
REMOTE CONTROL 6~9
INDOOR UNIT 10~11
TROUBLESHOOTING 12
INFORMATION 13
QUICK GUIDE BACK COVER
NOTE : The illustrations in this manual are for explanation purposes only and may differ from the actual unit.They are
subjected to change without notice for future improvement.
FRANÇAIS
TABLE DES MATIÈRES
TABLE DES MATIÈRES
ATTENTION: Si la température extérieure sort de la plage de températures
ci-dessus, la capacité thermique chutera de façon importante et il se peut que
l’unité extérieure s’arrête pour le contrôle de protection.
CONDITION D’UTILISATION
CONDITION D’UTILISATION
Utilisez ce climatiseur en respectant la plage de températures suivante
Température (°C) Unité intérieure Unité extérieure
*DBT *WBT *DBT *WBT
REFROIDIS-
SEMENT Max. 32 23 43 26
Min. 16 11 -10 -
CHAUFFAGE Max. 30 - 24 18
Min. 16 - -20 -
+8/10°C
DE CHAUFFAGE Max. 10 - - -
Min. 8 - -20 -
* DBT: Température sèche * WBT: Température humide
CONSIGNES DE SÉCURITÉ
14~15
TÉLÉCOMMANDE 16~19
UNITÉ INTÉRIEURE 20~21
DÉPANNAGE 22
INFORMATIONS 23
GUIDE RAPIDE
DOS DE COUVERTURE
REMARQUE : Les illustrations de ce mode d’emploi sont fournies à titre d’exemple uniquement et peuvent présenter des différences
par rapport à l’appareil proprement dit. Celui-ci peut être modifié sans préavis à des fins d’amélioration.
ESPAÑOL
CONTENIDO
CONTENIDO
AVISO: Cuando la temperatura exterior esté fuera del intervalo de temperatura
superior, la capacidad del equipo disminuirá significativamente y la unidad
exterior podría pararse como protección.
CONDICIONES DE FUNCIONAMIENTO
CONDICIONES DE FUNCIONAMIENTO
Utilice este aparato de aire acondicionado dentro del siguiente intervalo
de temperaturas
Temperatura (°C) Interior Exterior
*DBT *WBT *DBT *WBT
ENFRIAMIENTO
Máx. 32 23 43 26
Mín. 16 11 -10 -
CALENTAMIENTO
Máx. 30 - 24 18
Mín. 16 - -20 -
+8/10°C
CALOR Máx. 10 - - -
Mín. 8 - -20 -
* DBT: Temperatura en seco * WBT: Temperatura en húmedo
PRECAUCIONES DE
SEGURIDAD 24~25
MANDO A DISTANCIA 26~29
UNIDAD INTERIOR 30~31
LOCALIZACIÓN DE AVERÍAS
32
INFORMACIÓN 33
GUÍA RÁPIDA
CUBIERTA TRASERA
NOTA : Las ilustraciones de este manual sirven únicamente para describir las explicaciones y pueden no coincidir exactamente con las
del aparato suministrado. Están sujetas a cambios sin previo aviso con el fin de mejorar el producto.
Nous vous remercions d’avoir porté votre choix sur un climatiseur Panasonic
Thank you for purchasing Panasonic Air Conditioner
Muchas gracias por elegir una unidad de aire acondicionado Panasonic
F568728_YB0512-1062.indb 2F568728_YB0512-1062.indb 2 6/11/2012 9:43:23 AM6/11/2012 9:43:23 AM

3
DEUTSCH
INHALT
INHALT
BETRIEBSBEREICHE
BETRIEBSBEREICHE
Verwenden Sie dieses Klimagerät in folgenden Temperaturbereichen
Temperatur (°C) Innen Außen
*TK *FK *TK *FK
KÜHLEN Max. 32 23 43 26
Min. 16 11 -10 -
HEIZEN Max. 30 - 24 18
Min. 16 - -20 -
+8/10°C
HEIZBETRIEB Max. 10 - - -
Min. 8 - -20 -
* TK: Trockenkugeltemperatur * FK: Feuchtkugeltemperatur
HINWEIS: Wenn sich dieAußentemperatur außerhalb des oben genannten
Bereiches befindet, fällt die Heizleistung erheblich ab, und dasAußengerät kann
durch Schutzmaßnahmen abgeschaltet werden.
SICHERHEITSHINWEISE
34~35
FERNBEDIENUNG 36~39
INNENGERÄT 40~41
STÖRUNGSSUCHE 42
INFORMATIONEN 43
KURZANLEITUNG
RÜCKSEITE
HINWEIS : DieAbbildungen in diesem Handbuch dienen nur Erläuterungszwecken und können sich von dem tatsächlichen Gerät
unterscheiden. Sie können durch künftige Verbesserungen am Gerät ohne vorherigeAnkündigung geändert werden.
ITALIANO
INDICE
INDICE
CAVVISO: Quando la temperatura esterna non è ricompresa tra la gamma delle
temperature di cui sopra, la capacità di riscaldare diminuirà sensibilmente e
l’unità esterna può arrestarsi seguendo un comando di sicurezza.
CONDIZIONI OPERATIVE
CONDIZIONI OPERATIVE
Questo condizionatore può essere utilizzato con temperature rientranti nel
seguente intervallo
Temperatura (°C) Interna Esterna
*DBT *WBT *DBT *WBT
RAFFREDDAMENTO
Max. 32 23 43 26
Min. 16 11 -10 -
RISCALDAMENTO
Max. 30 - 24 18
Min. 16 - -20 -
+8/10°C
RISCALDAMENTO
Max. 10 - - -
Min. 8 - -20 -
*DBT: Temperatura con bulbosecco * WBT: Temperaturacon bulbo bagnato
PRECAUZIONI PER LA
SICUREZZA 44~45
TELECOMANDO 46~49
UNITÀ INTERNA 50~51
SOLUZIONE DEI PROBLEMI
52
INFORMAZIONI 53
GUIDA RAPIDA
COPERCHIO POSTERIORE
NOTA : le illustrazioni contenute in questo manuale sono riportate esclusivamente a scopo esplicativo e potrebbero differire
dall’apparecchio vero e proprio. I contenuti del presente manuale sono soggetti a modifica senza preavviso e verranno aggiornati
in base alle innovazioni future.
NEDERLANDS
INHOUDSOPGAVE
INHOUDSOPGAVE
OPMERKING: Wanneer de buitentemperatuur buiten het hierboven vermelde
temperatuurbereik ligt, zal de verwarmingscapaciteit aanzienlijk afnemen
en zal de buiten-unit door een beveiligingsvoorziening misschien niet meer
functioneren.
GEBRUIKSOMSTANDIGHEDEN
GEBRUIKSOMSTANDIGHEDEN
Gebruik deze airconditioner binnen het volgende temperatuurbereik
Temperatuur (°C) Binnen Buiten
*DBT *WBT *DBT *WBT
KOELEN Max. 32 23 43 26
Min. 16 11 -10 -
VERWARMEN Max. 30 - 24 18
Min. 16 - -20 -
+8/10°C
VERWARM Max. 10 - - -
Min. 8 - -20 -
* DBT: Droge bolttemperatuur * WBT: Natte bolttemperatuur
VEILIGHEIDSMAATREGELEN
54~55
AFSTANDSBEDIENING56~59
BINNENUNIT 60~61
PROBLEMEN OPLOSSEN 62
INFORMATIE 63
SNELLE GIDS
ACHTERKLEP
OPMERKING : De afbeeldingen in deze handleiding zijn alleen bedoeld als toelichting en kunnen afwijken van het daadwerkelijke
uiterlijk van het apparaat. Deze handleiding kan zonder voorafgaande kennisgeving worden gewijzigd ter verbetering.
Wir danken Ihnen für den Kauf Ihres Panasonic-Klimageräts
Grazie per aver acquistato un climatizzatore Panasonic
Hartelijk dank voor de aanschaf van de Panasonicairconditioner
F568728_YB0512-1062.indb 3F568728_YB0512-1062.indb 3 6/11/2012 9:43:24 AM6/11/2012 9:43:24 AM

4
SAFETY PRECAUTIONS
To prevent personal injury, injury to others, or property
damage, please comply with the following.
Incorrect operation due to failure to follow instructions below
may cause harm or damage, the seriousness of which is
classified as below:
WARNING
WARNING
This sign warns of death or serious injury.
CAUTION
CAUTION
This sign warns of injury or damage to property.
The instructions to be followed are classified by the following
symbols:
This symbol denotes an action that is PROHIBITED.
These symbols denote an actions that is
COMPULSORY.
WARNING
WARNING
INDOOR UNITAND OUTDOOR UNIT
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety. Children should be supervised to
ensure that they do not play with the appliance.
Please consult authorized dealer or specialist to
clean the internal parts, repair, install, remove
and reinstall the unit. Improper installation and
handling will cause leakage, electric shock or
fire.
Confirm to authorized dealer or specialist on
usage of specified refrigerant type. Using of
refrigerant other than the specified type may
cause product damage, burst and injury etc.
Do not install the unit in a potentially explosive
or flammable atmosphere. Failure to do so could
result in fire.
Do not insert your fingers or other
objects into the air conditioner indoor
or outdoor unit, rotating parts may
cause injury.
Do not touch the outdoor unit during lightning, it
may cause electric shock.
Do not expose yourself directly to cold air for a
long period to avoid excess cooling.
Do not sit or step on the unit, you may
fall down accidentally.
REMOTE CONTROL
Do not allow infants and small children to play
with the remote control to prevent them from
accidentally swallowing the batteries.
POWER SUPPLY
Do not use a modified cord,
joint cord, extension cord or
unspecified cord to prevent
overheating and fire.
To prevent overheating, fire or electric shock:
• Do not share the same power outlet with other
equipment.
• Do not operate with wet hands.
• Do not over bend the power supply cord.
• Do not operate or stop the unit by inserting or
pulling out the power plug.
Air Inlet
Air Inlet
Air Outlet
Air Outlet
Air Outlet
Air Outlet
Air Inlet
Air Inlet
Remote
Control
Power
Supply
Indoor
Unit
Outdoor
Unit
F568728_YB0512-1062.indb 4F568728_YB0512-1062.indb 4 6/11/2012 9:43:24 AM6/11/2012 9:43:24 AM

ENGLISH
5
CAUTION
CAUTION
INDOOR UNITAND OUTDOOR UNIT
Do not wash the indoor unit with water, benzene,
thinner or scouring powder to avoid damage or
corrosion at the unit.
Do not use for preservation of precise
equipment, food, animals, plants, artwork
or other objects. This may cause quality
deterioration, etc.
Do not use any combustible equipment in front of
the airflow outlet to avoid fire propagation.
Do not expose plants or pet directly to airflow to
avoid injury, etc.
Do not touch the sharp aluminium fin,
sharp parts may cause injury.
Do not switch ON the indoor unit when waxing
the floor.After waxing, aerate the room properly
before operating the unit.
Do not install the unit in oily and smoky areas to
prevent damage to the unit.
Do not dismantle the unit for cleaning purpose to
avoid injury.
Do not step onto an unstable bench when
cleaning the unit to avoid injury.
Do not place a vase or water container on the
unit. Water may enter the unit and degrade the
insulation. This may cause an electric shock.
Do not open window or door for long time during
COOL/DRY mode operation.
Ensure drainage pipe is connected properly and
keep drainage outlet clear of gutters, containers
or does not immersed in water to prevent water
leakage.
After a long period of use or use with any
combustible equipment, aerate the room
regularly.
After a long period of use, make sure the
installation rack does not deteriorate to prevent
the unit from falling down.
REMOTE CONTROL
Do not use rechargeable (Ni-Cd) batteries.
It may damage the remote control.
To prevent malfunction or damage of the remote
control:
• Remove the batteries if the unit is not going to
be used for a long period of time.
• New batteries of the same type must be
inserted following the polarity stated.
POWER SUPPLY
Do not pull the cord to disconnect the plug to
prevent electric shock.
WARNING
WARNING
POWER SUPPLY
If the supply cord is damage, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
It is strongly recommended to be installed
with Earth Leakage Circuit Breaker (ELCB)
or Residual Current Device (RCD) to prevent
electric shock or fire.
To prevent overheating, fire or electric shock:
• Insert the power plug properly.
• Dust on the power plug should be periodically
wiped with a dry cloth.
Stop using the product if any abnormality/failure
occurs and disconnect the power plug or turn off
the power switch and breaker.
(Risk of smoke/fire/electric shock)
Examples of abnormality/failure
• The ELCB trips frequently.
• Burning smell is observed.
• Abnormal noise or vibration of the unit is
observed.
• Water leaks from the indoor unit.
• Power cord or plug becomes abnormally hot.
• Fan speed cannot be controlled.
• The unit stops running immediately even if it is
switched on for operation.
• The fan does not stop even if the operation is
stopped.
Contact your local dealer immediately for
maintenance/repair.
This equipment must be earthed to prevent
electrical shock or fire.
Prevent electric shock by switching off the power
supply and unplug when:
- Before cleaning or servicing.
- Extended non-use.
-Abnormally strong lightning activity.
F568728_YB0512-1062.indb 5F568728_YB0512-1062.indb 5 6/11/2012 9:43:25 AM6/11/2012 9:43:25 AM

6
NOTES
Remote
Control display
3
2
1
Maximum distance: 7m
Human activity sensor
REMOTE CONTROL
Movable panel
Indicator
(Blue) (Orange) (Green)(Green)
POWER NANOE-G TIMER +8/10°C
(Green)
Press the remote control’s button
1TO SELECT OPERATION MODE POWER
AUTO mode - For your convenience
•
During operation mode selection the power indicator blinks.
• Unit selects operation mode every 30 minutes according to
temperature setting, outdoor and room temperature.
HEAT mode - To enjoy warm air
• Unit takes a while to warm up. The power indicator blinks during this
operation.
• This air conditioner removes frost automatically by two types of
operation.
• Unit removes ice formed on outdoor unit by methods below.
• Deice with heating operation (HEAT CHARGE Operation).
Unit has a heat absorbing device which accumulates heat
generated by outdoor unit while performing the heating operation
to remove ice formed on outdoor unit for maximum 6 minutes.
During this operation, the discharge temperature and fan speed
may be lowered when outdoor temperature is low, or the room is
not warmed up sufficiently, or set temperature is high.
• Deice without heating operation
Unit stops heating operation to remove large amount of ice
formed on outdoor unit for maximum 12 minutes.
During this operation, the power indicator blinks and the vertical
airflow direction louver is left open.
The heating operation resumes once this operation is completed.
COOL mode - To enjoy cool air
• Use curtains to screen off sunlight and outdoor heat to reduce power
consumption during cool mode.
DRY mode - To dehumidify the environment
• Unit operates at low fan speed to give a gentle cooling operation.
MOVABLE PANEL
• Opens for air intake when operation starts, and closes when operation
stops. During this time, do not hold it as it may cause malfunction or
breakdown.
F568728_YB0512-1062.indb 6F568728_YB0512-1062.indb 6 6/11/2012 9:43:26 AM6/11/2012 9:43:26 AM

ENGLISH
7
NOTES
NOTES
, , , ,
• Can be activated in all modes and can be cancelled by
pressing the respective button again. • Cannot be selected at the same time.
• operation can be activated independently.
2TO SET TEMPERATURE
• Selection range : 16°C ~ 30°C.
• Operating the unit within the recommended temperature
could induce energy saving.
HEAT mode : 20°C ~ 24°C.
COOLmode : 26°C ~ 28°C.
DRYmode : 1°C ~ 2°C lower than room temperature.
3TO TURN OFF THE UNIT
4TO SELECT FAN SPEED
FAN
S
PEED
AUTO
• ForAUTO, the indoor fan speed is automatically adjusted
according to the operation mode.
5TOADJUST AIRFLOW DIRECTION
AIR SWING
AUTO
AUTO
• Keeps the room ventilated.
• In COOL/DRYmode, ifAUTO is set, the louver swing
left/right and up/down automatically.
• In HEAT mode, ifAUTO is set, the horizontal louver fix at
predetermined position. The vertical louver swing left/right
after the temperature rises.
• In POWERFULmode, ifAUTO is set, the vertical louvers
fix at center position of the room according to installation
location setting.
6TO REACH TEMPERATURE QUICKLY
• The temperature setting and the Fan speed automatically
adjusted for higher performance, and will adjust for
adequate operation once the temperature is reached.
• Press the button again or turn OFF the unit to stop this
operation.
7TO ENJOY QUIET OPERATION
• This operation reduces airflow noises.
8TO CHANGE SETTINGACCORDING TO LIVING
ENVIRONMENT
• Complete below procedures to change the settings.
• 3 options are available in MENU.
CENTER BRIGHTNESS CONTRAST
• Select preference setting.
• Indoor unit installation location
CENTER LEFT RIGHT
• Indoor unit indicator brightness
BRIGHTER
LED
DIMMER
LED
ECONAVI
OFF
• Remote control LCD contrast
CONTRAST
3456 712
• Press SET to confirm the setting.
5
67
4
8
F568728_YB0512-1062.indb 7F568728_YB0512-1062.indb 7 6/11/2012 9:43:27 AM6/11/2012 9:43:27 AM

8
REMOTE CONTROL
NOTES
NOTES
, , , , ,
• Can be activated in all modes and can be cancelled by
pressing the respective button again. • Cannot be selected at the same time.
• operation can be activated independently.
9TO MONITOR HUMAN PRESENCE & ACTIVITY,
SUNLIGHT FOR ENERGY SAVING & COMFORT
ECONAVI
To optimize energy
saving
• When the operation is activated, the unit will start to
initialize for approximately 1 minute.
• After initialization, the human activity sensor will start
to detect the level of heat source & movement, the unit
adjusts the temperature and airflow to keep you comfort
consistently.
+1°C
Fan Speed
COLD/DRY Mode
Set Temperature +1°C
Low High Normal None
Fan Speed -2°C
-2°C
HEAT Mode
Set Temperature
Heat Source & Movement
• The human activity sensor will also scan for area of heat
source and movement in a room.
• The unit will determine the heat source & movement
hotspot, and automatically adjust horizontal airflow
direction louver either fix at predetermined position.
Detection area (top view)
5m
160º
• When manualAIR SWING or FAN SPEED is
selected, the ECONAVI operation will be cancel.
• The human activity sensor may not detect moving objects
further than 5m away or beyond detection angle.
• The human activity sensor sensitivity is influenced by
indoor unit location, movement speed, temperature range,
etc.
• The human activity sensor may:
- Mistakenly detects an object with heat source &
movement similar to human, such as pets, etc. as
human being.
- Mistakenly detects as non-heat source & movement if
a person stays motionless for certain period of time.
• The sunlight sensor detects sunlight intensity coming
through windows and differentiates between sunny
and cloudy/night to further optimize energy saving by
adjusting the temperature.
Ambient condition SunnyCloudy/
Night SunnyCloudy/ Night
COOL/DRY Mode
Set Temperature
HEAT Mode
Set Temperature -1°C -1°C
+1~2°C
ECONAVI is activated while it is cloudy / night
ECONAVI is activated while it is sunn
y
• In a room without window or with thick curtain, the
sunlight sensor will judge as cloudy/night.
• When sunlight sensor judge as cloudy/night, the indoor
unit indicator will automatically dim.
12
13
15
11
10
9
16
14
F568728_YB0512-1062.indb 8F568728_YB0512-1062.indb 8 6/11/2012 9:43:29 AM6/11/2012 9:43:29 AM

ENGLISH
9
10 TO MONITOR HUMAN PRESENCE & ACTIVITY
• The human activity sensor will scan for the heat source
and movement in the room.
• The unit will determine the heat source & movement
hotspot, and automatically adjust horizontal airflow
direction louver fix at predetermined position.
• When manualAIR SWING or FAN SPEED is
selected,AUTO COMFORToperation will be cancel.
11 TO PURIFY THE AIR NANOE-G
• Removes/deactivates harmful micro-organisms such as
viruses, bacteria, etc.
• nanoe-G starts automatically when the unit switched on.
12 TO USE MAINTENANCE HEATING
+ 8/10°C
• Maintain indoor temperature at +8/10ºC. Fan switches to
high fan speed automatically.
• This operation overwrite the operation mode and could be
cancelled by pressingAUTO, HEAT, COOLor DRYmode.
• Deice operation at outdoor unit will result in
sudden cold air from indoor unit. Eliminate
cold air with heat mode.
10°C
8°C
13 INFO
• Press during HEAT orAUTO mode to retrieve level of heat
stored in heat absorbing device; HEAT CHARGE level 1
(min.) to 4 (max.). “--” will be displayed during COOL, DRY
or NANOE-G mode.
• Press to retrieve error code when the unit stops and the
timer indicator blinks.
If the signal transmission is failed, (PRESSAGAIN).
14 TO TURN OFF THE UNITAFTER ASLEEP
0.5
SLEEP 1 2 3 5 7 9hr Cancel
• When used together with the timer, sleep operation has a
priority.
15 PRESS TO RESTORE THE INDOOR UNIT
SETTING
• To restore the remote control’s default setting, remove the
batteries.
NOTES
16 TO SET THE TIMER
• 2 sets of ON and OFF timers are available to turn ON or
OFF the unit at different preset time.
• Complete below procedures to set each timer:
Cancel
Cancel
TIMER
Select ON or OFF timer Set the
time Confirm
• Example of application at living room:
Morning: ON at 07:00 (Wake up)
OFF
at 08:00 (Out for work)
Evening: ON at 17:00 (Back home)
OFF
at 22:00 (Sleep)
• To cancel ON or OFF timer, press or to
select respective or then press .
• If timer is cancelled manually or due to power failure,
you can restore the timer again by pressing or
to select respective or then press .
• Upcoming timer will be displayed and will be activated
in sequence.
• When ON Timer is set, the unit may start earlier (up to 15
minutes at COOLmode, up to 40 minutes at HEAT mode)
before the actual set time in order to achieve the desired
temperature on time.
• Timer operation is based on the clock set in the remote
control and repeats daily once set. For clock setting,
please refer to Remote Control Preparation on the back
cover.
F568728_YB0512-1062.indb 9F568728_YB0512-1062.indb 9 6/11/2012 9:43:31 AM6/11/2012 9:43:31 AM

10
POWER NANOE-G TIMER +8/10°C
INDOOR UNIT
CLEANING INSTRUCTIONS
CLEANING INSTRUCTIONS
HINT
HINT
• Do not use benzene, thinner or scouring powder.
• Use only soap ( pH7) or neutral household detergent.
• Do not use water hotter than 40°C.
• To ensure optimal performance of the unit, cleaning
maintenance has to be carried out at regular intervals.
Dirty unit may cause malfunction and you may see error
code “H99”. Please consult authorized dealer.
2
9
1
73
10
8
6HUMAN ACTIVITY SENSOR
• Do not hit or violently press the sensor or
poke it with a sharp object. This can lead
to damage and malfunction.
• Do not place large objects near the
sensor and keep away heating units
or humidifiers from the sensor’s
detection area. This may lead to sensor
malfunction.
11 nanoe-G GENERATOR
• Do not touch during operation.
5
1INDOOR UNIT
• Wipe the unit gently with a soft, dry cloth.
2FRONT PANEL WITH MOVABLE PANEL
Remove Front Panel
• Raise and pull to remove the front panel.
• Wash gently and dry.
Close Front Panel
• Press down both ends of the front panel to close it securely.
• Do not remove the movable panel from front panel.
3REMOTE CONTROL RECEIVER
4SUNLIGHT SENSOR
5ALUMINIUM FIN
6HUMAN ACTIVITY SENSOR
7HORIZONTALAIRFLOW DIRECTION LOUVER
• Do not adjust by hand.
8VERTICALAIRFLOW DIRECTION LOUVER
• Do not adjust by hand.
•Switch off the power supply and unplug before cleaning.
•Do not touch the aluminium fin, sharp parts may cause injury.
4
F568728_YB0512-1062.indb 10F568728_YB0512-1062.indb 10 6/11/2012 9:43:33 AM6/11/2012 9:43:33 AM