Panasonic S-22MU1E5A Instruction manual

85464869272000 REFERENCE NO.TD831172-00
Indoor Unit
Class 2215 28 36 45 56 60 73 90 106
K1
Wall Mounted
140
T2
Ceiling
160
U1
4-Way Cassette
K2
Wall Mounted
Y2
4-Way Cassette
60×60
F2
Low Silhouette
Ducted
S-22MU1E5A
S-22MK2E5AS-15MK2E5A
S-22MY2E5AS-15MY2E5A
S-22MF2E5AS-15MF2E5A
S-28MU1E5A
S-28MK2E5A
S-28MY2E5A
S-28MF2E5A
S-36MT2E5A
S-36MU1E5A
S-36MK2E5A
S-36MY2E5A
S-36MF2E5A
S-45MK1E5A
S-45MT2E5A
S-45MU1E5A
S-45MY2E5A
S-45MF2E5A
S-56MK1E5A
S-56MT2E5A
S-56MU1E5A
S-56MY2E5A
S-56MF2E5A
S-60MU1E5A
S-60MF2E5A
S-73MK1E5A
S-73MT2E5A
S-73MU1E5A
S-73MF2E5A
S-90MU1E5A
S-90MF2E5A
S-106MK1E5A
S-106MT2E5A
S-106MU1E5A
S-106MF2E5A
S-140MT2E5A
S-140MU1E5A
S-140MF2E5A
S-160MU1E5A
S-160MF2E5A
Order No. SBPAC1403010CE
VRF SYSTEMS INDOOR UNIT
4-Way Cassette
(U1 type)
Low Silhouette Ducted
(F2 type)
Ceiling
(T2 type)
TD831172-00VRFSYSINDOOR.indb1TD831172-00VRFSYSINDOOR.indb1 2014/06/1910:37:482014/06/1910:37:48

2-2
Design of VRF SYSTEM
1
2
3
4
5
6
7
8
9
1. Electrical Wiring
1-1. General Precautions on Wiring
(1)
(2)
(3)
(4)
(5)
(6)
Before wiring, confirm the rated voltage of the unit as shown
on its nameplate, then carry out the wiring closely following
the wiring diagram.
Provide a power outlet to be used exclusively for each
unit, and a power supply disconnect, circuit breaker and
earth leakage breaker for overcurrent protection should be
provided in the exclusive line.
To prevent possible hazards from insulation failure, the unit
must be grounded.
Each wiring connection must be done in accordance with
the wiring system diagram. Wrong wiring may cause the
unit to misoperate or become damaged.
Do not allow wiring to touch the refrigerant tubing,
compressor, or any moving parts of the fan.
Unauthorized changes in the internal wiring can be very
dangerous. The manufacturer will accept no responsibility
for any damage or misoperation that occurs as a result of
such unauthorized changes.
(7)
(8)
The remote control wiring and the inter-unit control wiring
should be wired apart from the inter-unit power wiring.
Use shielded wires for inter-unit control wiring between
units and ground the shield on both sides.
(9)
1-2. Recommended Wire Length and Wire Diameter for Power Supply System
Control wiring
(C) Inter-unit control wiring
(between outdoor and indoor units)
0.75 mm² (AWG #18)
Use shielded wiring*
Max. 1,000 m
(D) Remote control wiring
0.75 mm² (AWG #18)
Max. 500 m
NOTE * With ring-type wire terminal.
(E) Control wiring for group control
0.75 mm² (AWG #18)
Max. 200 m (Total)
(10)
Regulations on wire diameters differ from locality to
locality. For field wiring rules, please refer to your LOCAL
ELECTRICAL CODES before beginning. You must
ensure that installation complies with all relevant rules and
regulations.
To prevent malfunction of the air conditioner caused by
electrical noise, care must be taken when wiring as follows:
If the power supply cord of this appliance is damaged,
it must be replaced by a repair shop appointed by the
manufacturer, because special purpose tools are required.
Use a waterproof conduit for outdoor unit wiring to avoid
damaging the wire and to prevent accumulation of liquid
inside the unit.
Indoor unit
Type (B) Power supply Time delay fuse or
circuit capacity
2.5 mm²Minimum 2 mm²
Max. 150 m
Max. 130 m
Max. 150 m 10 – 16 A
15 A
15 A
K1
K2
Y2
U1 10 – 16 A
Max. 130 m
F2 10 – 16 A
Max. 130 m
T2 10 – 16 A
Max. 130 m
TDxxxxxx-002WAYVRF.indb2TDxxxxxx-002WAYVRF.indb2 2014/01/3017:52:302014/01/3017:52:30

2-3
Design of VRF SYSTEM
1
2
3
4
5
6
7
8
9
1. Electrical Wiring
1-3. Wiring System Diagrams
(1) Refer to Section 1-2. “Recommended Wire Length and
Wire Diameter for Power Supply System” for the
explanation of “B”, “C”, “D” and “E” in the above
diagram.
(2) The basic connection diagram of the indoor unit shows
the 7P terminal board, so the terminal boards in your
equipment may differ from the diagram.
(3) Refrigerant Circuit (R.C.) address should be set before
turning the power on.
(4) Address setting can be executed by remote controller
automatically. Refer to Section 5.
U2
U1
R2
R1
L
N
R2
R1
R2
R1
R2
R1
2
1
2
1
U2
U1
L
N
U2
U1
L
N
U2
U1
L
N
2
1
2
1
2
1
D
E
C
B
L
N
L
N
L
N
L
N
2
1
B
B
B
C
D
D
C
C
Power supply
220/230/240V ~50/60Hz
Remote
controller
Remote
controller
Remote
controller
WHT
BLK
WHT
BLK
WHT
BLK
Power supply
220/230/240V ~50/60Hz
Power supply
220/230/240V ~50/60Hz
Power supply
220/230/240V ~50/60Hz
Ground
Ground
Ground
Ground
Ground
Ground
To outdoor unit
Outdoor unit
Ground
Ground
Ground
Ground
Ground
Indoor unit
(No. 1)
Indoor unit
(No. 2)
Indoor unit
(No. n)
Indoor unit
(No. 3)
Group control:
LN U1U2
5P terminal board
Power
supply
K1 Type
K2 Type
Unit
control
line
L N U1 U2 R1 R2
LNU1 U2 R1 R2
6P terminal board
Power
supply
Unit
control
line
Remote
control
line
U1 Type
6P terminal board
F2 Type
Power
supply
Remote
control
line
Unit
control
line
6P terminal board
Power
supply
cable
Inter-unit
control
wiring
Remote
control
wiring
Y2 Type
Terminal Board
Power supply
cable
Inter-unit con-
trol wiring
Inter-unit con-
trol wiring
Fig. 2-1
L N U1 U2 R1 R2
6P terminal board
T2 Type
Power
supply
Remote
control
line
Unit
control
line
TDxxxxxx-002WAYVRF.indb3TDxxxxxx-002WAYVRF.indb3 2014/01/3017:52:302014/01/3017:52:30

2-4
Design of VRF SYSTEM
1
2
3
4
5
6
7
8
9
1. Electrical Wiring
(1)
(2)
When linking the outdoor units in a network, disconnect the terminal extended from the short plug from
all outdoor units except any one of the outdoor units.
(When shipping: In shorted condition.)
For a system without link (no wiring connection between outdoor units), do not remove the short plug.
Do not install the inter-unit control wiring in a way that forms a loop.
Outdoor unit Indoor unit
Indoor unit
Indoor unit
Indoor unit
NO
Branch point
Outdoor unit Outdoor unit Outdoor unit
Prohibited
Prohibited
Indoor unit Indoor unit Indoor unit Indoor unit Indoor unit
CAUTION
(3) Do not install inter-unit control wiring such as star branch wiring. Star branch wiring causes mis-address
setting.
(4) If branching the inter-unit control wiring, the number of branch points should be 16 or fewer.
Fig. 2-2
Fig. 2-3
Fig. 2-4
Central Controller
Outdoor unit
Outdoor unit
Outdoor unit
Indoor unit Indoor unit Indoor unit
Indoor unit Indoor unit
Indoor unit Indoor unit
Indoor unit
Indoor unit
: Branch point
More than 2m required
TDxxxxxx-002WAYVRF.indb4TDxxxxxx-002WAYVRF.indb4 2014/01/3017:52:302014/01/3017:52:30

2-5
Design of VRF SYSTEM
1
2
3
4
5
6
7
8
9
1. Electrical Wiring
Shielded wire
Ground Ground
Screw and
Special washer
Ring
pressure
terminal
Terminal board
Ring pressure
terminal
Screw
Special
washer
Wire
Wire
Insulation tape
8mm
Insulation tape
Shield mesh
Shield mesh
Fig. 2-5
Stranded wire
Ring
pressure
terminal
Strip 10 mm
Fig. 2-6
Fig. 2-7
Fig. 2-8
Fig. 2-9
Fig. 2-10
Fig. 2-11
(5)
Use shielded wires for inter-unit control wiring (c) and
ground the shield on both sides, otherwise misoperation
from noise may occur. (Fig. 2-5)
Connect wiring as shown in Section “1-3. Wiring System
Diagrams”.
(6) Connecting cable between indoor unit and outdoor unit shall be approved polychloroprene sheathed
5 or 3 *1.5 mm2flexible cord. Type designation 60245 IEC 57 (H05RN-F, GP85PCP etc.) or heavier
cord.
WARNING
Loose wiring may cause the terminal to overheat or result in unit malfunction.
A fire hazard may also occur.
Therefore, ensure that all wiring is tightly connected.
When connecting each power wire to the terminal, follow the instructions on “How to connect wiring to the terminal”
and fasten the wire securely with the fixing screw of the terminal board.
How to connect wiring to the terminal
For stranded wiring
(1)
then strip the insulation to expose
the stranded wiring about 10 mm and
tightly twist the wire ends. (Fig. 2-6)
(2)
remove the terminal screw(s) on the
terminal board.
(3)
pliers, securely clamp each stripped
wire end with a ring pressure terminal.
(4)
Cut the wire end with cutting pliers,
Using a Phillips head screwdriver,
Using a ring connector fastener or
Place the ring pressure terminal,
and replace and tighten the removed
terminal screw using a screwdriver.
(Fig. 2-7)
Examples of shield wires
(1)
(2)
together.
Coat with insulation tube or wrap insulation tape after
putting tightly. (Fig. 2-9)
(3)
(4)
Remove cable coat not to scratch braided shield. (Fig. 2-8)
Ravel braided shield carefully and put tightly braided shield
Remove coat of signal wire. (Fig. 2-10)
Connect signal wire removed coat and shield wire with
pressure terminal. (Fig. 2-11)
Earth wire for power supply
The earth wire should be longer than the other lead wires for
electrical safety.
Use the standard power supply cables for Europe (such as H05RN-F or H07RN-F which conform to
CENELEC (HAR) rating specifications) or use the cables based on IEC standard. (60245 IEC57, 60245
IEC66)
TDxxxxxx-002WAYVRF.indb5TDxxxxxx-002WAYVRF.indb5 2014/01/3017:52:302014/01/3017:52:30

2-6
Design of VRF SYSTEM
1
2
3
4
5
6
7
8
9
1. Electrical Wiring
Wiring sample
Use this screw when connecting the shield
for the Inter-unit control wiring to ground.
Functional ground screw (External Electronic
Expansion Valve Kit and Schedule Timer)
Protective ground screw
(External Solenoid Valve Kit for 3WAY)
Power Supply
Clamping Clip
Inter-unit Control Wiring
Clamper*1
Remote Control Wiring
U1 type
*1Fasten tightly.
Clamper*1
Clamper*1
Use this screw when connecting the shield
for the Inter-unit control wiring to ground.
Functional ground screw
(External Electronic Expansion Valve Kit
and Schedule Timer)
Protective ground screw
(External Solenoid Valve Kit for 3WAY)
Power Supply
Inter-unit Control Wiring
Remote Control Wiring
F2 type
TDxxxxxx-002WAYVRF.indb6TDxxxxxx-002WAYVRF.indb6 2014/01/3017:52:302014/01/3017:52:30

2-11
Design of VRF SYSTEM
1
2
3
4
5
6
7
8
9
2. SELECTING THE INSTALLATION SITE
2-3. Low Silhouette Ducted (F2 type)
AVOID:
areas where leakage of flammable gas may be expected.
places where large amounts of oil mist exist.
direct sunlight.
locations near heat sources which may affect the
performance of the unit.
locations where external air may enter the room directly.
This may cause “condensation” on the air discharge ports,
causing them to spray or drip water.
locations where the remote controller will be splashed with
water or affected by dampness or humidity.
installing the remote controller behind curtains or furniture.
locations where high-frequency emissions are generated.
DO:
select an appropriate position from which every corner of the room can be uniformly cooled.
select a location where the ceiling is strong enough to support the weight of the unit.
select a location where tubing and drain pipe have the shortest run to the outdoor unit.
allow room for operation and maintenance as well as unrestricted air flow around the unit.
install the unit within the maximum elevation difference above or below the outdoor unit and within a total tubing length (L)
from the outdoor unit as detailed in the Installation Instructions provided with the outdoor unit.
allow room for mounting the remote controller about 1 m off the floor, in an area that is not in direct sunlight or in the flow
of cool air from the indoor unit.
If the indoor unit is installed on the ceiling where the temperature or humidity inside is high (over 30°C/RH: 70%),
add insulating material to the surface of the unit to avoid dew condensation.
25 cm
25 cm
25 cm
Fig. 2-14
TDxxxxxx-002WAYVRF.indb11TDxxxxxx-002WAYVRF.indb11 2014/01/3017:52:302014/01/3017:52:30

4-1
VRF SYSTEMS Indoor Unit Specifications
1
2
3
4
5
6
7
8
9
Contents
4. VRF SYSTEMS INDOOR UNIT SPECIFICATIONS
1. 4-Way Cassette Type (U1 Type) .........................................................................................
1-1. Specifications .................................................................................................................4-2
4-6
4-17
4-20
4-22
4-25
4-29
4-41
4-43
4-45
4-49
4-51
4-57
4-58
4-60
4-2
4-25
4-49
4-63
4-65
4-69
4-70
4-71
4-63
1-2. Major Component Specifications....................................................................................
1-3. Dimensional Data ........................................................................................................
1-4. Noise Criterion Curves ................................................................................................
1-5. Air Flow Distance / Temperature Chart .......................................................................
2. Low Silhouette Ducted Type (F2 Type) ...........................................................................
2-1. Specifications ...............................................................................................................
2-2. Major Component Specifications..................................................................................
2-3. Dimensional Data ........................................................................................................
2-4. Noise Criterion Curves ................................................................................................
2-5. External Static Pressure Setting ..................................................................................
3. 4-Way Cassette 60×60 Type (Y2 Type) ............................................................................
3-1. Specifications ...............................................................................................................
3-2. Major Component Specifications..................................................................................
3-3. Dimensional Data ........................................................................................................
3-4. Noise Criterion Curves ................................................................................................
3-5. Air Flow Distance / Temperature Chart .......................................................................
4. Wall Mounted Type (K2 Type) ..........................................................................................
4-1. Specifications ..............................................................................................................
4-2. Major Component Specifications..................................................................................
4-3. Dimensional Data ........................................................................................................
4-4. Noise Criterion Curves ................................................................................................
4-5. Air Flow Distance / Temperature Chart .......................................................................
4-73
4-77
4-81
4-82
4-83
4-735. Wall Mounted Type (K1 Type) ..........................................................................................
5-1. Specifications ...............................................................................................................
5-2. Major Component Specifications..................................................................................
5-3. Dimensional Data ........................................................................................................
5-4. Noise Criterion Curves ................................................................................................
5-5. Air Flow Distance / Temperature Chart .......................................................................
4-85
4-87
4-93
4-94
4-95
4-85
4-98
6. Ceiling Type (T2 Type) ......................................................................................................
6-1. Specifications ..............................................................................................................
6-2. Major Component Specifications..................................................................................
4-98
4-99
7-1. Precautions Regarding External Air Intake .................................................................
7-2. External Air Intake Volume & Resistance Within Unit /
Operation Noise Characteristics.........................
6-3. Dimensional Data ........................................................................................................
6-4. Noise Criterion Curves ................................................................................................
6-5. Air Flow Distance / Temperature Chart .......................................................................
7. Fresh Air Intake ................................................................................................................
4-Way Cassette (U1 Type)
Ceiling (T2 Type)
Low Silhouette Ducted (F2 Type)
4-Way Cassette 60×60 (Y2 Type)
TD831172-00VRFSYSINDOOR.indb1TD831172-00VRFSYSINDOOR.indb1 2014/04/2416:48:422014/04/2416:48:42

4-25
VRF SYSTEMS Indoor Unit Specifications
1
2
3
4
5
6
7
8
9
2. Low Silhouette Ducted Type (F2 Type)
2-1. Specifications
Unit specifications (A)
INDOOR MODEL S-15MF2E5A S-22MF2E5A S-28MF2E5A
PANEL MODEL - - -
PERFORMANCE TEST CONDITION ISO15042 / AS / NZS3823 / EN14511 / EN12102
POWER SUPPLY ø, Hz 1ø 50/60Hz 1ø 50/60Hz 1ø 50/60Hz
V 220 230 240 220 230 240 220 230 240
C
O
O
L
I
N
G
CAPACITY
kW 1.50 1.50 1.50 2.2 2.2 2.2 2.8 2.8 2.8
BTU/h 5100 5100 5100 7500 7500 7500 9600 9600 9600
kcal/h(Fri./h) - - - - - - - - -
CURRENT A 0.60 0.57 0.56 0.60 0.57 0.56 0.60 0.57 0.56
INPUT POWER W 70 70 70 70 70 70 70 70 70
ANNUAL CONSUMPTION W *4 - - - - - - - - -
EER/EER CLASS
(W/W)*5/("A"~"G") ---------
EER BTU/hW - - - - - - - - -
POWER FACTOR % - - - - - - - - -
NOISE INDOOR
(H/M/L)
dB-A 33/29/22 33/29/22 33/29/22
Power Level dB 55/51/44 55/51/44 55/51/44
NOISE OUTDOOR
(H/L)
dB-A - - -
Power Level dB - - -
H
E
A
T
I
N
G
CAPACITY
kW 1.70 1.70 1.70 2.5 2.5 2.5 3.2 3.2 3.2
BTU/h 5800 5800 5800 8500 8500 8500 10900 10900 10900
kcal/h(Fri./h) - - - - - - - - -
CURRENT A 0.60 0.57 0.56 0.60 0.57 0.56 0.60 0.57 0.56
INPUT POWER W 70 70 70 70 70 70 70 70 70
COP/COP CLASS
(W/W)*5/("A"~"G") ---------
COP BTU/hW - - - - - - - - -
POWER FACTOR % - - - - - - - - -
NOISE INDOOR
(H/M/L)
dB-A 33/29/22 33/29/22 33/29/22
Power Level dB 55/51/44 55/51/44 55/51/44
NOISE OUTDOOR
(H/L)
dB-A - - -
Power Level dB - - -
EXTRA LOW TEMP CAPACITY(kW)/INPUT POWER(W)/COP ---
Cooling
MAX CURRENT(A)/MAX INPUT POWER(W) 0.86 / 105 0.82 / 105 0.79 / 105 0.86 / 105 0.82 / 105 0.79 / 105 0.86 / 105 0.82 / 105 0.79 / 105
Heating MAX CURRENT(A)/MAX INPUT POWER(W) 0.86 / 105 0.82 / 105 0.79 / 105 0.86 / 105 0.82 / 105 0.79 / 105 0.86 / 105 0.82 / 105 0.79 / 105
STARTING CURRENT(A)/COMP OUTPUT(W) - - - - - - - - -
NETWORK IMPEDANCE (ΩMAX.) *3 - - -
FM OUTPUT (ID/OD) W 119 119 119
MOISTURE REMOVAL VOLUME L/h(Pt/h) 0.9 (1.9) 1.3 (2.7) 1.6 (3.4)
External static pressure
Pa 70 (MIN10 - MAX150) 70 (MIN10 - MAX150) 70 (MIN10 - MAX150)
I/D AIR
FLOW
COOL m3/min (ft3/min) 14/13/9 (494/459/318) 14/13/9 (494/459/318) 14/13/9 (494/459/318)
HEAT m3/min (ft3/min) 14/13/9 (494/459/318) 14/13/9 (494/459/318) 14/13/9 (494/459/318)
O/D AIR
FLOW
COOL m3/min (ft3/min) - - -
HEAT m3/min (ft3/min) - - -
REFRIGERANT TYPE, AMOUNT g(oz) - - -
P
R
O
D
I
M
HEIGHT : H mm(inch) 290 (11-7/16) 290 (11-7/16) 290 (11-7/16)
WIDTH : W mm(inch) 800 (31-1/2) 800 (31-1/2) 800 (31-1/2)
DEPTH : D mm(inch) 700 (27-9/16) 700 (27-9/16) 700 (27-9/16)
P
A
C
D
I
M
HEIGHT : H mm 355 355 355
WIDTH : W mm 1014 1014 1014
DEPTH : D mm 850 850 850
MASS (NET) kg(lb) 29 (64) 29 (64) 29 (64)
(GROSS) kg(lb) 36 (80) 36 (80) 36 (80)
LAYERS LIMIT (actually) 9 (10) 9 (10) 9 (10)
Operation
Condition
Cool (DBT) - - -
Heat (DBT) - - -
P
I
P
I
N
G
PIPE DIAMETER mm (inch) (Liquid) ø6.35 (1/4) (Gas) ø12.7 (1/2) (Liquid) ø6.35 (1/4) (Gas) ø12.7 (1/2) (Liquid) ø6.35 (1/4) (Gas) ø12.7 (1/2)
CONNECT METHOD, STD LENGTH m (ft) fl ared type fl ared type fl ared type
PIPE LENGTH RANGE m (ft) ------
I/D & O/D HEIGHT DIFFERENCE m (ft) ------
ADD GAS AMOUNT
g
/m (oz/ft) ------
PIPE LENGTH FOR ADDITIONAL GAS m (ft) ------
*3:Network Impedance shall be applicable for EUROPE and CHINA models.
*4:The annual consumption is calculated by multiplying the input power at 230V(400V) by an average of 500 hours per year in cooling mode.
*5:EER and COP classification is at 230V(400V) only in accordance with EU directive 2002/31/EC.
*:In case it is necessary to indicate the air flow volume in (l/s), the value in (m3/min.) shall be multiplied by 16.7 and rounded down the decimal point.
*: If the EUROVENT Certified models can be operated under the "extra-low" temperature condition, -7°C dry bulb and -8°C wet-bulb temperatures with rated voltage
230V shall be used.
TD831172-00VRFSYSINDOOR.indb25TD831172-00VRFSYSINDOOR.indb25 2014/04/2416:49:162014/04/2416:49:16

4-26
VRF SYSTEMS Indoor Unit Specifications
1
2
3
4
5
6
7
8
9
2. Low Silhouette Ducted Type (F2 Type)
2-1. Specifications
Unit specifications (B)
INDOOR MODEL S-36MF2E5A S-45MF2E5A S-56MF2E5A
PANEL MODEL - - -
PERFORMANCE TEST CONDITION ISO15042 / AS / NZS3823 / EN14511 / EN12102
POWER SUPPLY ø, Hz 1ø 50/60Hz 1ø 50/60Hz 1ø 50/60Hz
V 220 230 240 220 230 240 220 230 240
C
O
O
L
I
N
G
CAPACITY
kW 3.6 3.6 3.6 4.5 4.5 4.5 5.6 5.6 5.6
BTU/h 12300 12300 12300 15400 15400 15400 19100 19100 19100
kcal/h(Fri./h) - - - - - - - - -
CURRENT A 0.60 0.57 0.56 0.60 0.57 0.56 0.77 0.74 0.71
INPUT POWER W 70 70 70 70 70 70 100 100 100
ANNUAL CONSUMPTION W *4 - - - - - - - - -
EER/EER CLASS
(W/W)*5/("A"~"G") ---------
EER BTU/hW - - - - - - - - -
POWER FACTOR % - - - - - - - - -
NOISE INDOOR
(H/M/L)
dB-A 33/29/22 34/32/25 34/32/25
Power Level dB 55/51/44 56/54/47 56/54/47
NOISE OUTDOOR
(H/L)
dB-A - - -
Power Level dB - - -
H
E
A
T
I
N
G
CAPACITY
kW 4.2 4.2 4.2 5.0 5.0 5.0 6.3 6.3 6.3
BTU/h 14300 14300 14300 17100 17100 17100 21500 21500 21500
kcal/h(Fri./h) - - - - - - - - -
CURRENT A 0.60 0.57 0.56 0.60 0.57 0.56 0.77 0.74 0.71
INPUT POWER W 70 70 70 70 70 70 100 100 100
COP/COP CLASS
(W/W)*5/("A"~"G") ---------
COP BTU/hW - - - - - - - - -
POWER FACTOR % - - - - - - - - -
NOISE INDOOR
(H/M/L)
dB-A 33/29/22 34/32/25 34/32/25
Power Level dB 55/51/44 56/54/47 56/54/47
NOISE OUTDOOR
(H/L)
dB-A - - -
Power Level dB - - -
EXTRA LOW TEMP CAPACITY(kW)/INPUT POWER(W)/COP ---
Cooling
MAX CURRENT(A)/MAX INPUT POWER(W) 0.86 / 105 0.82 / 105 0.79 / 105 0.86 / 105 0.82 / 105 0.79 / 105 1.00 / 125 0.96 / 125 0.92 / 125
Heating MAX CURRENT(A)/MAX INPUT POWER(W) 0.86 / 105 0.82 / 105 0.79 / 105 0.86 / 105 0.82 / 105 0.79 / 105 1.00 / 125 0.96 / 125 0.92 / 125
STARTING CURRENT(A)/COMP OUTPUT(W) - - - - - - - - -
NETWORK IMPEDANCE (ΩMAX.) *3 - - -
FM OUTPUT (ID/OD) W 119 119 119
MOISTURE REMOVAL VOLUME L/h(Pt/h) 2.1 (4.4) 2.5 (5.3) 3.2 (6.7)
External static pressure
Pa 70 (MIN10 - MAX150) 70 (MIN10 - MAX150) 70 (MIN10 - MAX150)
I/D AIR
FLOW
COOL m3/min (ft3/min) 14/13/9 (494/459/318) 14/13/10 (494/459/353) 16/15/12 (565/530/424)
HEAT m3/min (ft3/min) 14/13/9 (494/459/318) 14/13/10 (494/459/353) 16/15/12 (565/530/424)
O/D AIR
FLOW
COOL m3/min (ft3/min) - - -
HEAT m3/min (ft3/min) - - -
REFRIGERANT TYPE, AMOUNT g(oz) - - -
P
R
O
D
I
M
HEIGHT : H mm(inch) 290 (11-7/16) 290 (11-7/16) 290 (11-7/16)
WIDTH : W mm(inch) 800 (31-1/2) 800 (31-1/2) 800 (31-1/2)
DEPTH : D mm(inch) 700 (27-9/16) 700 (27-9/16) 700 (27-9/16)
P
A
C
D
I
M
HEIGHT : H mm 355 355 355
WIDTH : W mm 1014 1014 1014
DEPTH : D mm 850 850 850
MASS (NET) kg(lb) 29 (64) 29 (64) 29 (64)
(GROSS) kg(lb) 36 (80) 36 (80) 36 (80)
LAYERS LIMIT (actually) 9 (10) 9 (10) 9 (10)
Operation
Condition
Cool (DBT) - - -
Heat (DBT) - - -
P
I
P
I
N
G
PIPE DIAMETER mm (inch) (Liquid) ø6.35 (1/4) (Gas) ø12.7 (1/2) (Liquid) ø6.35 (1/4) (Gas) ø12.7 (1/2) (Liquid) ø6.35 (1/4) (Gas) ø12.7 (1/2)
CONNECT METHOD, STD LENGTH m (ft) fl ared type fl ared type fl ared type
PIPE LENGTH RANGE m (ft) ------
I/D & O/D HEIGHT DIFFERENCE m (ft) ------
ADD GAS AMOUNT
g
/m (oz/ft) ------
PIPE LENGTH FOR ADDITIONAL GAS m (ft) ------
*3:Network Impedance shall be applicable for EUROPE and CHINA models.
*4:The annual consumption is calculated by multiplying the input power at 230V(400V) by an average of 500 hours per year in cooling mode.
*5:EER and COP classification is at 230V(400V) only in accordance with EU directive 2002/31/EC.
*:In case it is necessary to indicate the air flow volume in (l/s), the value in (m3/min.) shall be multiplied by 16.7 and rounded down the decimal point.
*: If the EUROVENT Certified models can be operated under the "extra-low" temperature condition, -7°C dry bulb and -8°C wet-bulb temperatures with rated voltage
230V shall be used.
TD831172-00VRFSYSINDOOR.indb26TD831172-00VRFSYSINDOOR.indb26 2014/04/2416:49:162014/04/2416:49:16