Panasonic AW-PH350P User manual
-
1
-
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicans.Any attempt to service or repair
the product or products deal with in this service manual by anyone else could result in serious injury or death.
AW-PH350P
-
2
-
AW-PH350E
-
3
-
GENERAL GUIDELINES
1. When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been over-
heated or damaged by the short circuit.
2. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
3. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
LEAKAGE CURRENT COLD CHECK
1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohm meter,
between the jumpered AC plug and each exposed
metallic cabinet part on the equipment such as
screwheads, connectors, control shafts, etc. The
resistance value must be more than 5MΩ.
Figure1
LEAKAGE CURRENT HOT CHECK (See Figure 1)
1. Plug the AC cord directly into the AC outlet.
Do not use an isolation transformer for this check.
2. Connect a 1.5kΩ, 10W resistor, in parallel with a 0.15µ
F capacitor, between each exposed metallic part on the
set an a good earth ground such as a water pipe, as
shown in Figure1.
3. Use an AC voltmeter, with 1000 ohms/volt or more
sensitivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the
voltage at each point.
5. Reverses the AC plug in the AC outlet repeat each of the
above measurements.
6. The potential at any point should not exceed 0.15 volts
RMS. A leakage current tester (Simpson Model 229
equivalent) may be used to make the hot checks, leakage
current must not exceed 0.1 milliamp. In case a
measurement is outside of the limits specified, there is a
possibility of a shock hazard, and the equipment should
be repaired and rechecked before it is returned to the
customer.
ELECTROSTATICALLY SENSITIVE (ES) DEVICES
Some semiconductor (solid state) devices can be damaged
easily by static electricity. Such components commonly are
called Electrostatically sensitive (ED) Devices. Examples of
typical ES devices are integrated circuits and some field-
effect transistors and semiconductor “chip” components. The
following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor
component or semiconductor-equipped assembly, drain
off any electrostatic charge on your body by touching a
known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist trap device, which should be removed
for potential shock reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface
such as aluminum foil, to prevent electrostatic charge
buildup or exposure of the assembly.
3. Use only a grounded tip soldering iron to solder or
unsolder ES devices.
4. Use only an anti-static solder removal device classified as
“anti-static” can generate electrical charges sufficient to
damage ES devices.
5. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage ES
devices.
6. Do not remove a replacement ES device from its
protective package until immediately before you are
ready to install it.
(most replacement ES devices are package with leads
electrically shorted together by conductive foam,
aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from
the leads of a replacement ES device, touch the
protective material to the chassis or circuit assembly into
which the device will be installed.
CAUTION : Be sure no power is applied to the chassis or
circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpacked
replacement ES devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the
lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ES device).
X-RADIATION
WARNING
1. The potential source of X-radiation in EVF sets is the
High Voltage section and the picture tube.
2. When using a picture tube test jig for service, ensure that
jig is capable of handling 10kV without causing x-
radiation.
Note : It is important to use an accurate periodically
calibrated high voltage meter.
3. Measure the High Voltage. The meter (electric type)
reading should indicate 2.5kV, 0.15kV. If the meter
indication is out of tolerance, immediate service and
correction is required to prevent the possibility of
premature component failure. To prevent an x-radiation
possibility, it is essential to use the specified picture tube.
SAFETY PRECAUTIONS
±
AC VOLTMETER
Hot-Check Circuit
TO
APPLIANCES
EXPOSED
METAL PARTS
COLD
WATER PIPE
(EARTH GROUND)
1500Ω
0.15µF
10W
-
4
-
About indication of a circuit name
J
12 13 14 15
COMPONENT
NAME F1:SERVO (CTL)
VEP82230A-1
CIRCUIT BOARD NO.
KR2D53 (1/17)
DRAWING NO.
SCM001
16
K
Circuit Name
Drawing No.
Page No.
Circuit Board No.
NOTE:
DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER
SHOWN IN THE PARTS LIST.
AND MAY BE SLIGHTLY DIFERENT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
CAUTION
THE MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM THE SECONDARY
CIRCUIT.
PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS.
IMPORTANT SAFETY NOTICE:
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SAME TYPE.
SCHEMATIC DIAGRAMS
NOTE:
BE SURE TO MAKE YOUR ORDERS OF REPLACEMENT PARTS ACCORDING TO PARTS LIST, SECTION3
CO
NTENT
S
INTERCONNECTION ........................................................................................ SCM001
COMP P.C.BOARD ........................................................................................... SCM002
CON P.C.BOARD.............................................................................................. SCM006
MOTOR AMP P.C.BOARD ............................................................................... SCM007
CPU P.C.BOARD .............................................................................................. SCM008
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMPONENT
NAME INTERCONNECTION
CIRCUIT BOARD NO. DRAWING NO.
01/01
SCM001
A
B
C
D
E
F
G
H
I
J
123456789101112131415
COMPONENT
NAME
COMP P.C.BOARD
VEP20908A
CIRCUIT BOARD NO.
KR30250 (1/4)
DRAWING NO.
01/04
SCM002
A
B
C
D
E
F
G
H
I
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMPONENT
NAME
COMP P.C.BOARD
VEP20908A
CIRCUIT BOARD NO.
KR30250(2/4)
DRAWING NO.
02/04
SCM003
A
B
C
D
E
F
G
H
I
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMPONENT
NAME
COMP P.C.BOARD
VEP20908A
CIRCUIT BOARD NO.
KR30250 (3/4)
DRAWING NO.
03/04
SCM004
A
B
C
D
E
F
G
H
I
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMPONENT
NAME
COMP P.C.BOARD
VEP20908A
CIRCUIT BOARD NO.
KR30250 (4/4)
DRAWING NO.
04/04
SCM005
A
B
C
D
E
F
G
H
I
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMPONENT
NAME
CON P.C.BOARD
VEP20909A
CIRCUIT BOARD NO.
KR1F48 (1/1)
DRAWING NO.
01/01
SCM006
A
B
C
D
E
F
G
H
I
J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
COMPONENT
NAME
MOTOR AMP P.C.BOARD
1A880S015
CIRCUIT BOARD NO. DRAWING NO.
01/01
SCM007
A
B
C
D
E
F
G
H
I
J
123456789101112131415
COMPONENT
NAME
CPU P.C.BOARD
WPH60JKZ1A
CIRCUIT BOARD NO. DRAWING NO.
01/01
SCM008
A
B
C
D
E
F
G
H
I
J
1
2
3
6
5
4
1
2
3
6
5
4
12 3
13
12
14
12 3
121212
6
5
7
2
3
1
4
11
32
41
1
2
3
6
5
4
2
3
1
4
11
2
3
1
4
11
13
12
14
32
41
12
13
12
14
12 3
6
5
7
9
10
8
9
10
8
6
5
7
9
10
8
9
10
8
13
12
14
2
3
1
4
11
6
5
7
6
5
7
13
12
14
10
9
8
7
6
5
4
3
25
24
21
23
2
20
26
27
22 14
28
11
12
13
15
16
17
18
19
A0 D0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
D1
D2
D3
D4
D5
D6
D7
CS1
CS2
WE
OE
VCC
GND
2
3
1
4
11
6
5
7
13
12
14 9
10
8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
PA23/WRHH
PE14/TIOC4C/DACK0/AH
PE15/TIOC4D/DACK1/IRQOUT
PA22/WRHL
PA21/CASHH
VSS
PC0/A0
PC0/A1
PC0/A2
PC0/A3
PC0/A4
PC5/A5
PC6/A6
PC7/A7
PC8/A8
PC9/A9
PC10/A10
PC11/A11
PC12/A12
PC13/A13
PC14/A14
PC15/A15
PB0/A16
PB1/A17
VSS
VCC
VCC
VSS
PA20/CASHL
PA19/BACK/DRAK1
PB2/IRQ0/POE0/RAS
PB3/IRQ1/POE1/CASL
PB4/IRQ2/POE2/CASH
PB5/IRQ3/POE3/RDWR
VSS
PA18/BREQ/DRAK0
PB5/IRQ3/POE3/RDWR
PB6/IRQ4/A18/BACK
PB7/IRQ5/A19/BREQ
PB8/IRQ6/A20/WAIT
PA14/RD
VCC
PB9/IRQ7/A21/ADTRG
VSS
WDTOVF
PD31/D31/ADTRG
PD30/D30/IRQOUT
PA13/WRH
PA12/WRL
PA11/CS1
PA10/CS0
PA9/TCLKD/IRQ3
PA8/TCLKC/IRQ2
PA7/TCLKB/CS3
PA6/TCLKA/CS2
VSS
VCC
PD29/D29/CS3
PD28/D28/CS2
PD27/D27/DACK1
PD26/D26/DACK0
PD25/D25/DREQ1
PD24/D24/DREQ0
VSS
PD23/D23/IRQ7
PD22/D22/IRQ6
PD21/D21/IRQ5
PD20/D20/IRQ4
PD19/D19/IRQ3
PD18/D18/IRQ2
PD17/D17/IRQ1
VSS
PD16/
RES
MD0
MD1
MD2
NMI
MD3
PA15/CK
PLLVSS
PLLCAP
PLLVCC
PA17/WAIT
PA16/AH
VCC(FWP)
EXTAL
XTAL
VSS
PD0/D0
PD1/D1
PD2/D2
PD3/D3
PD4/D4
PD5/D5
PD6/D6
PD7/D7
PD8/D8
PD9/D9
PD10/D10
VSS
VSS
VCC
VCC
PD11/D11
PD12/D12
PD13/D13
PD14/D14
PD15/D15
IRQ0/
IRQ0
PE0/TIOC0A/DREQ0
PE1/TIOC0B/DRAK0
PE3/TIOC0D/DRAK1
PE2/TIOC0C/DREQ1
VCC
PE4/TIOC1A
PE5/TIOC1B
PE6/TIOC2A
VSS
VSS
PF0/AN0
PF1/AN1
PF2/AN2
PF3/AN3
PF4/AN4
PF5/AN5
PF6/AN6
PF7/AN7
AVS S
AVref
AVC C
PA0/RXD0
PA3/RXD1
PA4/TXD1
PA1/TXD0
PA1/SCK0/DREQ0/IRQ0
PA5/SCK1/DREQ1/IRQ1
VCC
PE7/TIOC2B
PE8/TIOC3A
PE9/TIOC3B
PE10/TIOC3C
VSS
PE11/TIOC3D
PE12/TIOC4A
PE13/TIOC4B/MRES
1
3
5
9
11
13
7
2
4
6
8
10
12
14
1A1Y
2A2Y
3A3Y
4A4Y
5A5Y
6A6Y
GNDVCC
2
O
1I
3
G
2
O
1I
3
G
1 4
2
5
10
1
2
3
4
6
7
8
9
5
10
1
2
3
4
6
7
8
9
3
1
9
11
13
5
7
4
2
8
10
12
6
14
1A 1Y
2A 2Y
3A 3Y
4A 4Y
5A 5Y
6A 6Y
GND VCC
1
2
3
45
6
7
8
5
10
1
2
3
4
6
7
8
9
1
2
TAL2 C
TAL2 R
1R1
2AGND1
3R2
4R3
5CAP
6REF
7AGND2
8SB/BTC
9EXT/INT
14
TAG
15
R/C
11
SYNC
18
PWRD
10 DGND
12
DATA C L K
13
DATA
19
VAN A
20
VDIG
16
#CS
17
#BUSY
5
10
1
2
3
4
6
7
8
9
5
10
1
2
3
4
6
7
8
9
2VCC
4PFI
6
WD
3GND
7
RESET
5
PFO
1VOUT 8
VBATT
1,32
2
3
1
8
4
5
6
7
1
2
3
6
5
4
1VS 2
VO
3
G
5
10
1
2
3
4
6
7
8
9
1
2
3
4
5
6
7
14
13
12
11
10
9
8
13
1
3
9
11
5
7
12
2
4
8
10
6
14
1A 1Y
2A 2Y
3A 3Y
4A 4Y
5A 5Y
6A 6Y
GND VCC
1
3
5
9
11
13
7
2
4
6
8
10
12
14
1A 1Y
2A 2Y
3A 3Y
4A 4Y
5A 5Y
6A 6Y
GND VCC
2
3
1
5
10
1
2
3
4
6
7
8
9
1
2
3
4
LWC
LWS
SVC C
DGND
13 X0
14 X1
15 X2
12 X3
1X4
5X5
2X6
4X7
6INH
11
A10
B9
C
3
X
16
VDD
7VEE 8
VSS
5
10
1
2
3
4
6
7
8
9
1
2
3
4
5
6
7
8
9
A+
A-
A COM
B+
MVCC
B-
MTR ON
NC
MGND
1
2
3
4
5
VCC
NC
GND
VCC
GND
1
2
3
4
5
6
7
ND C
ND R
EXT C
EXT R
CVCC
CGND
NC
1
2
3
6
5
4
6
4
1
3
5
10
1
2
3
4
6
7
8
9
5
10
1
2
3
4
6
7
8
9
1
2
3
4
16
15
14
13
5
6
7
8
12
11
10
9
1
2
3
4
12 3
12 3
12 3
12 3
12 3
12 3
12 3
12 3
12 3
1
2
3
4
5
6
7
8
AD1
AGND
AD2
AGND
AGND
AD3
AGND
AD4
12 3
12 3
12 3
1NC
2+VIN
3+VIN
4C
5NC
6RC
7G
8NC
9NC
10 NC
11 VAD J
12 NC
13 +VOUT
12 3
12 3
MGND
MGNDMGND
MGNDMGND
MGND
MGND
12 3
MGND
MGND
VCC
DVCC
AVC C
DVCC
DVC C
DVCC
AVC C
DVC C
AVCC
AVC C
DVC C
DVC C DVCC
DVC C
DVCC
DVCC
DVCC
DVC C
DVC C
DVC C
DVC C
DVC C
DVCC
DVC C
BVCC
BVCC
VCC
CVCC
CVCC
AVC 1
AVCC
AVC1
AVC 1
AVC1
CGND
CGND
VCC
AVC C
GND
GND
GND
GND
DVCC
1
2
3
4
TXD232 2
RXD232 2
DGND
NC
1
2
3
4
5
6
7
8
9
10
DI UP
DI DOWN
DI LEFT
DI RIGHT
DI OPTSEL
DO RUN
TXD232 1
RXD232 1
DGND
DGND
1
2
TAL1 C
TAL1 R
1
2
3
VREF 5
VI PAN
AGND
1
2
3
VREF 5
VI TILT
AGND
1
3
4
5
11
10
12
9 8
13
7
14
15
6
2
16
C1+
C2+
C2
C1
T1I
T2I T2O
T1O
R1O R1I
R2O R2I
VCC
GND
V
V+
10
14
15
16
18
21
24
20
1
32
2
3
4
5
6
7
8
9
33
44
12
22 13
11
17
34
31
30
29
27
28
23
43
42
41
37
40
36
25
39
35
26
38
19
D0
D1
D2
D3
D4
D5
D6
D7
A0
A1
A2
CHSEL
TXRDY1
TXRDY2
WR
RD
MR
CS
VDD
VDD
VSS
VSS
XIN
XOUT
INTR1
INTR2
SOUT1
SOUT2
SIN1
SIN2
MF1
MF2
RTS1
CTS1
DTR1
DSR1
DCD1
RI1
RTS2
CTS2
DTR2
DSR2
DCD2
RI2
1
2
3
4
5
6
IRIS C
VO IRIS
VO ZOOM
VO FOCUS
NC
AGND
DVC C
1
3
5
9
11
13
7
2
4
6
8
10
12
14
1A1Y
2A2Y
3A3Y
4A4Y
5A5Y
6A6Y
GNDVCC
12 3
1
2
3
4
5
6
HOT2
HOT1
COLD1
COLD2
TALLY IN
DGND
5
10
1
2
3
4
6
7
8
9
DVC C
1
2
3
4
CVCC
CGND
CVCC
CGND
CGND
CVCC
9
10
8
4
11
C5 104
C3
104
R3
201
R2
302 C2
471
C14 104
R12
510
C15
151
TP1
(CLK)
C95
104
C96 101
R102 102
R4
105
R5
471
C6
100
C7
100
C86
104
C87
104
C91
104
C92
104
C88
104
C8 104
C9 104
C10 104
C11 104
C13 104
TP2
(CLK)
C1
104
R19
510
PM3
PM4
R14
913
C20
123
R15
101
C17
123
C16
102
R13
913
R16
913 R17
913
C21
682
C19
822
C18
103
R18
101
C23
102
C24
123
R20
913 R21
913
C28
123
R22
101
R23
913 R24
913
R25
101
C25
103
C26
822
C29
682
C27
104
C40
102
C41
153
R53
913 R54
913
C43
123
C42
104
R55
101
C46
102
C47
153
R61
913 R62
913
C48
123
R63
101
C50
102
C51
153
R69
913 R70
913
C52
123
R71
101
R56
623
C44
104
C39 101
R51
393
R57
101
D8
TP6
(VOIRIS)
R64
623
C45 101
R65
101
R59
393
R66
103
TP7
(VOIRIS)
R72
623
R73
101
C49
101
R67
393
R74
103
TP8
(VOIRIS)
R32
123
C32
101
R27
303
R26
203
TP3
(PANV)
R200
502
R203
502
R204
502
R205
502
R38
203
R39
303
R201
502
C35 101
TP4
(TILTV)
R42
123
TP5
(ACOM)
C37 101
R46
104
R47
303
C38
104
R50
243
R49
101
R31
103
C30
101
R29
103
R33
101
R34
103
C31
101
R30
103
R35
101
R41
103
C36
104
C33
101
R36
103
R43
101
R44
103
C34
101
R37
103
R45
101
C104
104
C103
220/25
C99 104
R117
103
R118
101
R120
103
C100
104 R119
393
R111
222
R112
222
R113
102
R115
102
R114
681
Q1
R116
681
Q2
R109
181
R110
181
R89
511
C67
100/35
C68 104
C75 104
C70
10/16
L2
522
C71
10/16
L1
522
C72
104
TP9
(AGND) TP10
(AGND)
C77
220/25
C78 104
C79
220/25
C83 104
C80
470/10
C81 104
C82
10/16
R93 475
R92
202
R91
0R00
C76 151
TP12
(DGND) TP13
(DGND)
TP11
(RESET)
R90 475
R97
123
R95
103
R96
101
C84
101
U9
R6 103
R7 103
R8 103
R9 103
R10 103
L3 102
L4 102
L5 102
L6 102
S3
S4
D31
R124 102
R125
103
R126
103
R123 102
R127
103
R122 102
R128
103
C97 104
R104 121R107 121
FL21FL22FL23
C62 104
C63
104
R82
104
C58
104
C57
104
R77
101
C59
101
R79 101
C54
473
C53
222
R75
223
C56
473
C55
222
R76
223
U12
C65
104
R85
101
C64
101
R84
104 R83
104
R87
104
C66
101
R88
101
R86
823
R81
101
R78
201
R80
333
R94
102
R11
202
C12
222
C85
104
R99
103
R101
103
R100
103
R98 104
R1
202
C4
222
C101
220/25
C102
104
U9
L8
C22 2.2/35
C60
2.2/35
C61
2.2/35
C69
10/35
C74
10/35
PM2
U6
U7
U7
L7
FL20
R129
0R00
R131
0R00
R132
0R00
R130
0R00
D18
U12
D11
D1
U6
U6
U7
U7
U9
U10
U10
U10
U10
U9
U6
C73
10/35
U4
U8
U8
U8
U8
R202
502
U2
D13
U20
C98 104
U23U22
D9
Y1
R184
103
R187
103
U5
S2
R183
103
D19
D20
D21
D22
D23
P12
U13
R182
103
R185
103
U15
BT1
U16
U16
PM1
D27
U1
R181
103
U19
U14
U3
U12
R188
681
P14
U11
R186
103
P2
P3
P8
PM5
D50
C89
104
C90
104
C93
104
C94
104
R180
103
R189
222
S1
PM6
D25
D14
D15
D16
D2
D3
D4
D5
D12
P13
R121 102
D30
D29
D28
U24
D7
D6
D26
P11
P5
D24
P9
P6
P7
U18
U17
P1
R58
103
D10
U21
D17
P10
R189
202
P4
U12
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
D0
A0
A1
A2
A3
D0
D1
D2
D3
D4
D5
D6
D7
D1
D2
D3
D4
D5
D6
D7
CIRCUIT BOARD DIAGRAMS
NOTE:
DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER
SHOWN IN THE PARTS LIST.
AND MAY BE SLIGHTLY DIFERENT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
CAUTION
THE MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM THE SECONDARY
CIRCUIT.
PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS.
IMPORTANT SAFETY NOTICE:
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SAME TYPE.
NOTE:
BE SURE TO MAKE YOUR ORDERS OF REPLACEMENT PARTS ACCORDING TO PARTS LIST, SECTION3
CONTENTS
CPU P.C.BOARD (WPH60JKZ1A) ........................................................................... CBA-1
COMP P.C.BOARD (VEP20908A) ............................................................................ CBA-2
CON P.C.BOARD (VEP20909A) ............................................................................... CBA-2
MOTOR P.C.BOARD (1A880S015) .......................................................................... CBA-2
CBA-1
CPU P.C.BOARD (WPH60JKZ1A)
(COMPONENT SIDE)
(FOIL SIDE)
CBA-2
COMP P.C.BOARD (VEP20908A)
(COMPONENT SIDE)
(FOIL SIDE)
CON P.C.BOARD (VEP20909A)
(FOIL SIDE) (COMPONENT SIDE)
MOTOR P.C.BOARD (1A880S015)
CONTENTS
Casing & Packing Parts Assembly..............................................................PRT-1
Electrical Replacement Parts List ...............................................................PRT-4
EXPLODED VIEWS
&
REPLA
C
EMENT PART
S
LI
S
T
S
PRT-1
CASING & PACKING PARTS ASSEMBLY
Components identified with the mark have the special characteristics for safety.
When replacing any of these components, use only the same type.
Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
M1 1A33B038-01 LOGO PLATE FOR COVER 1
M2 1A641A226-03 COVER 1
M4 1A405A002-01 SHEET FOR COVER 1
M5 1A405A003-01 SHEET FOR COVER 1
M12 1A880S024-01 GEAR HOUSING ASS'Y 1
M28 1A108F056-06 POST FOR HEAD 1 1A108F056-12
M29 1A108A001-05 CABLE CLAMP FOR HEAD 1
M30 1A331A246-01 CHASSIS FOR HEAD 1
M31 1A331A247-01 BODY FOR BASE 1
M32 1A355L147-01 I/O PANEL FOR HEAD 1
M33 1A355L134-01 PANEL A FOR BASE 1
M34 1A101A608-01 O-RING FOR BODY 1
M35 1A355L145-01 I/O PANEL FOR BASE 1
M36 1A108F092-02 BLOCK NUT FOR BASE 1
M37 1A108F056-28 POST FOR BASE 1
M38 1A101A522-01 O-RING FOR FLANGE 1
M39 1A363B041-01 FLANGE 1 1A353B039-01
M40 1A399A346-01 PLATE 1
M41 1A880S075-01 STAY 1
M42 1A411A102-01 PIN FOR STAY 1
M43 1A352B203-01 CUSHION FOR STAY 1
M44 1A411A102-01 SCREW FOR STAY 1
M45 1A355L136-01 PANEL C FOR HEAD 1
M46 1A355L134-01 PANEL A FOR BASE 1
M52 1A357A144-01 PANEL B FOR BASE 1
M53 1A880S025-01 GEAR HEAD ASS'Y (TILT) 1
M54 1A355C914-01 MOTOR BRACKET 2
CN101 R03-R6M CONNECTOR (ND/EXIT) 1
CN102 K1AA112J0004 CONNECTOR (LENS I/F) 2
1 LB2-4 PAN HEAD SCREWS 24
2 NM2-1 HEXAGON HEAD NUTS 2
3 AM3X0.5-8 HEXAGON CAP SCREW 3
4 AM3X0.5-10 HEXAGON CAP SCREW 11
5 LB3X0.5-6 PAN HEAD SCREW 3
6 LBWSM3-10B PAN HEAD SCREW AND WASHER 4
7 LB2.6-5 PAN HEAD SCREW 4
8 066N406-80 BINDING HEAD SCREW 2
9 NM3X0.5-1 HEXAGON HEAD NUT 2
10 LB3X0.5-4 PAN HEAD SCREW 4
11 LD4X0.7-12 BINDING HEAD SCREW 4
12 LD4X0.7-10B BINDING HEAD SCREW 2
13 AM3X0.5-12 CAP SCREW 3
14 1A108F091-02 SCREW 6
E1 WPH60JKZ1A CPU P.C.BOARD 1
E2 VEP20908A COMP P.C.BOARD 1
E3 VEP20909A CONNECTION P.C.BOARD 1
E4 1A880S015 MOTOR AMP P.C.BOARD 1
CN103 K1FB11SH0001 CONNECTOR (CAMERA I/F) 1
This manual suits for next models
1
Table of contents
Other Panasonic Audio & Video Accessories manuals
