Panasonic H-PS45175PP User manual

file:///C|/U.../Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_cvr.xml[11/12/2018 3:58:01 PM]
Order No.DSC1109054CE
B26
Interchangeable Lens for Digital Camera
Model No. H-PS45175PP
H-PS45175E
H-PS45175GK
Colour
Vol.1
(K)...............Black Type
(S)...............Silver Type

file:///C|/U.../Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_cvr.xml[11/12/2018 3:58:01 PM]
© Panasonic Corporation 2011 Unauthorized copying and distribution is a violation of law.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_01.xml[11/12/2018 3:58:26 PM]
1 Service Navigation
1.1 Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.

1.2 Important Notice
1.2.1 About LENS MAIN BLOCK UNIT (Ref. 212)
1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.212), because it requires
special facilities and equipment.
2. 
3. In case of the "LENS MAIN BLOCK UNIT"(Ref.212) defects, contact to the service department of sales company.
4. No adjustment is required when replacing the part mentioned on Fig.1-1. But, when tighten the concerned screws,apply proper
torque mentioned on "4. Disassembly and Assembly Instruction" section.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_02.xml[11/12/2018 3:59:44 PM]
2 Operating Guide
2.1 Before Use
(Information for Your Safety)
2.2 Cautions For Use

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_02.xml[11/12/2018 3:59:44 PM]
2.3 Components
Note;
Change in the image by the focus operation may be more visible depending on the recording condition when the AF operates during the motion

you.
2.3.1 Accessories

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_02.xml[11/12/2018 3:59:44 PM]
2.3.2 Attaching/Detaching the Lens

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_03.xml[11/12/2018 4:00:41 PM]
3 Service Fixture and Tools
3.1 Service Fixture and Tools
The following Service Fixture and Tools are used for Checking & Servicing for this unit.
3.2 Clean Box

10,000 (Federal Standard 209D).
(When remove the 1st lens frame, it is indispensable.)
[NOTE]

for cleaning.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_04.xml[11/12/2018 4:02:41 PM]
4 Disassembly and Assembly Instructions
4.1 Outline
Proceed disassemble and assemble, by referring the following table and Fig.4-1.
IMPORTANT:
1. It is recommended dealing with Clean box, to keep maintaining the dustproof environment.
(Refer to "3.2. Clean Box" section of this service manual for details.)
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with Lens caps (front &
rear), other than necessary cases.
3. 
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
NOTE:
1. 
2. Use VFK1390 (small driver) when screwing/unscrewing the B208.
CAUTION:
Keep covering the lens unit with Lens caps (front & rear), other than necessary
cases.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_04.xml[11/12/2018 4:02:41 PM]
4.2 Disassembly Procedure
1. Remove the 3 screws showed in the following picture, then remove SHADING FLAME UNIT.
(B201, B202, B203)
2. Remove the 4 screws showed in the following picture, then remove L MOUNT UNIT.
(B204, B205, B206 and B207)

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_04.xml[11/12/2018 4:02:41 PM]
3. Remove MOUNT SPACER.
4. 
(B209, B210, B211)
5. 
(4 FLOATING RUBBER is attached on LENS PCB UNIT.)

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_04.xml[11/12/2018 4:02:41 PM]
6. 
4.3 Assembly Procedure
1. 
2. 
3. Attach REAR FRAME UNIT on the LENS Body to set the mark of the two in the same direction.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_04.xml[11/12/2018 4:02:41 PM]
4. 
then set DUST PROOF RING in the REAR FRAME UNIT.
5. 
(Torque: 7 +/- 1N-cm)
6. Insert the Mount Spacer into the Lens Body.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_04.xml[11/12/2018 4:02:41 PM]
7. 
8. 

(Torque: 10 +/- 1.2N-cm)
9. 
connecting L MOUNT UNIT and MOUNT CONTACT UNIT in the same way.
(Torque: B204 to B206: 20 +/- 1.2N-cm, B207: 8 +/- 1N-cm)

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_04.xml[11/12/2018 4:02:41 PM]

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_05.xml[11/12/2018 4:04:07 PM]
5 Maintenance
5.1 About the Lens
5.1.1 Dust / Dirt on the outer casing part(s)
1. 
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
5.1.2 Dust / Dirt on the Lens Glasses.

1. When it is outside surface of the lens:
When the dust and / or dirt gets on the outer side surface of the Lens glasses, order the following procedures.
1. Blow off the dust on the Lens glass surface with the Blower, gently. (Do not Blow too strongly.)
2. Wipe out the dirt on the lens glass surface with Lens cleaning KIT (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in the Lens cleaning KIT in details.)
NOTE: (About rear side of lens unit.)
2. When it is inside of the lens:
Refer to the “5.2. General description (Lens cleaning)” section of this service manual.
5.2 General description (Lens cleaning)
When there is a dust / dirt inside surface of the 1st lens frame unit and/or subject side
surface of the 2nd lens frame unit, remove it by referring the following procedures.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_05.xml[11/12/2018 4:04:07 PM]
Important:
1. 
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "3.2. Clean Box", in details.
2. 
3. 
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
5.2.1 Disassembly procedure
Important:


(1) DECO.RING
1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring and lens glass), and peel off the decoration ring gently.
(2)FILTER RING UNIT
Remove the following 3 screws, then remove FILTER RING UNIT.
(B215 - B217: Silver 5mm)

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_05.xml[11/12/2018 4:04:07 PM]
(3) 1ST LENS FRAME UNIT
Remove the following 3 screws, then remove 1ST LENS FRAME UNIT.
(B212 - B214: Black 4mm)
(4) Removal of dusts / dirt.
1. Blow off the dust on the surface of the lens with a blower brush.
2. Use lens cleaning KIT(BK) (VFK1900BK), if necessary.
5.2.2 Assembly procedure
Important:

1. Set 1ST LENS FRAME UNIT on 2ND LENS FRAME UNIT with positioning the 3 holes of screw.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_05.xml[11/12/2018 4:04:07 PM]
2. 
(Torque: 7 +/- 1.2N-cm)
3. Attach FILTER RING UNIT on the Lens Body to set the mark of the two in the same direction.
4. 
(Torque: 10 +/- 1.2N-cm)
5. Install DECO.RING by referring the Phase marks.

file:///C|/U...l/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_05.xml[11/12/2018 4:04:07 PM]
(Use new one, Do not use the one which is removed.)

(Ref) The character "LUMIX G" of the DECO.RING is near the mark at the side surface of FILTER RING UNIT.

file:///C|/U...etabi/AppData/Local/Temp/Rar$EXa0.980/viewing/SGML_VIEW_DATA/ALL/H-PS45175PP/SVC/DSC1109054CE/doc/DSC1109054CE_06.xml[11/12/2018 4:04:40 PM]
6 Exploded View
6.1 Frame & Casing Section
6.2 Packing Parts and Accessories Section