Panasonic WORKIO DP-135 User manual



Digital Imaging Systems
Before operating this equipment, please read these instructions completely and keep these operating
instructions for future reference.
GettingTo KnowYour
Machine
J
?
I
Before StartingMaking CopiesOptionsOthers
Model No. DP-1810P
Operating Instructions
(For Copier)
English

2
IMPORTANT INFORMATION
When requesting information, supplies or service always refer to the model and serial number of your
machine.The model and serial number plate (Main Name Plate) is located on the rear side of machine.
For your convenience, space is provided below to record information you may need in the future.
Model No.
Serial No.
Date of Purchase
Dealer
Address
Telephone Number
( )
SuppliesTelephone Number
( )
ServiceTelephone Number
( )
Model and Serial Number
Copyright 2002 by Matsushita Graphic Communication Systems, Inc.
All rights reserved.Unauthorized copying and distribution is a violation of law.Printed in Japan.
The contents of these Operating Instructions are subject to change without notice.
(Digital copier with ADF option)

3
 
Operation Chart
Common Features and Usage
■■
■■
■Basic Operation
Original
1
Place the
Original 2
Original Size
(Reduction/
Enlargement
Only)
3
Copy Size
(Reduction/
Enlargement
Only)
4
Number
of Copies 5
Press
START
■■
■■
■Position of the Original
Load Paper
Turn Power
Switch On
INV INV LTR LGL LDR
LTR
LDR
INV
LTR
LGL
INV
INVOICE
INVOICE R
LETTER R
LEGAL
LEDGER
Original Guide
CPlace originals face down on the platen or face up on
the ADF.
CIf the original is not positioned properly, a portion of the
original may not be copied.
CFor originals smaller than invoice size, position the
original within the area of INVOICE and select invoice.
■■
■■
■Commonly Used Functions and Operating Procedures
Full Size
Makes a copy that is the same
size as the original 145
Reduction or Enlargement
Copies the original at a fixed
reduction or enlargement ratio 1 3 42 5
■■
■■
■Memory Capacity
When the memory becomes full during original scanning, the message “Function not available
for lack of memory” will be displayed in the message display. In this case, follow the operating
instruction in the message display.
When additional memory is required, consult with an authorized servicing dealer.
(See page 12)
(See page 13)
GettingTo KnowYour
Machine

4
Energy Star
As an ENERGY STAR®Partner, Panasonic has determined that this product meets the
ENERGY STAR®guidelines for energy efficiency.
This voluntary program specifies certain energy consumption and usage standards.This product
will automatically “power down”after a specified period of non-use.The use of this ENERGY
STAR®compliant product will reduce energy consumption and ultimately benefit the
environment.
The default functions can be adjusted depending on your office requirements.
Please see your authorized Panasonic dealer for more details.

5
Table of Contents
GettingTo KnowYour Machine
Operation Chart .............................................................................................................................. 3
■Common Features and Usage..............................................................3
Before Starting
Precautions ..................................................................................................................................... 7
Control Panel ................................................................................................................................ 10
Making Copies
Basic Copy .................................................................................................................................... 12
■Full Size Copying................................................................................12
■Reduction or Enlargement Copying ....................................................13
■Zoom Copying ....................................................................................14
■Using the Sheet Bypass .....................................................................15
Creative Features ......................................................................................................................... 16
■2 in 1 Copy .........................................................................................16
■2 Page Copy .......................................................................................17
■Book/Edge/Margin ..............................................................................18
■Job Memory .......................................................................................19
■Sort Copy ...........................................................................................20
Other Features.............................................................................................................................. 21
■Energy Saver/Interrupt Mode..............................................................21
■Skyshot Mode.....................................................................................22
Combined FunctionTable ............................................................................................................ 24
Function ........................................................................................................................................ 25
■Checking the Copier’sTotal Counter ...................................................25
■General Functions ..............................................................................26
■Copier Settings ...................................................................................27
■General Functions for Key Operator ...................................................28
■Copier Settings for Key Operator ........................................................29
■Function Setting..................................................................................30
■Function Setting for Key Operator.......................................................31
■ForYour Safety .....................................................................................8
■Handling ...............................................................................................8
■Toner and Paper ...................................................................................8
■Ventilation .............................................................................................8
■Installation ............................................................................................9
Table of Contents
Energy Star ..................................................................................................................................... 4

6
Table of Contents
Options
Accessories .................................................................................................................................. 35
■Components .......................................................................................35
■Automatic Document Feeder ..............................................................36
Problem Solving
Problem Solving ........................................................................................................................... 38
■Adding Paper (J) ...............................................................................38
■Adding theToner and ReplacingToner Waste Container (?)..............39
■Removing a Misfed Paper...................................................................41
Troubleshooting............................................................................................................................ 46
■Before Calling Service ........................................................................46
■User Error Codes (U Code) ................................................................48
Others
Specifications ............................................................................................................................... 49
Options and Supplies................................................................................................................... 51

7
Precautions
ForYour Safety
■■
■■
■Laser Safety
LASER SAFETY
This unit employs a laser.Only qualified service personnel should
attempt to service this device due to possible eye injury.
CAUTION:
USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE
PROCEDURES OTHERTHANTHOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
■■
■■
■Caution Labels
Manufacturer’s name and address Factory ID
Before Starting
(Digital copier with ADF option) (Digital copier with ADF option)

8
Precautions
Handling
■Do not look directly at the exposure lamp when
copying.
■Do not turn the power switch Off or open the front
panel during copying.
CDo not drop paper clips or other metal objects into
the copier.
Toner and Paper
■Store toner, drum and paper in cool areas with low
humidity.
CHigh quality paper of 16 - 24 lb (60 – 90 g/m2) [15 –
34 lb (56 – 128 g/m2) using the sheet bypass] may
be used.
CFor optimum performance, it is recommended that
only Panasonic Brand supplies are used in the
copier.
Ventilation
■The copier should be installed in a well-ventilated
area to minimize the ozone density in the air.

9
■The copier should not be installed in areas with the
followingconditions:
CExtremely high or low temperature and humidity.
Ambientconditions
Temperature: 50°F – 95°F (10°C – 35°C)
Relative humidity: 45% – 85%
CWhere temperature and humidity can change
rapidly, causing condensation.
CDirect exposure to sunlight.
CDirectly in the air conditioning flow.
CIn areas of high dust concentration.
CIn areas of poor ventilation.
CIn areas with chemical fume concentration.
CIn areas with extreme vibration.
CWith unstable or uneven conditions (floors, etc.).
■The maximum power consumption is 1.5 kW.
A properly wired (grounded), dedicated, 15A, 120VAC outlet is required.Do not use an extension
cord.
The power cord on this equipment must be used to disconnect the main power.Please ensure
that the socket outlet is installed near the equipment and is easily accessible.
FCCWARNING For U.S.A.
FCCWARNING:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his/her own expense.
The user could lose the authority to operate this equipment if any unauthorized changes or
modifications are made to this equipment.
Installation
Precautions
CTHIS PRODUCT CONTAINS A LITHIUM BATTERY.DANGER OF EXPLOSION IF
BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENTTYPE.DISPOSE OF USED
BATTERIES ACCORDING TO THE INSTRUCTIONS OFYOUR LOCAL SOLID WASTE
OFFICIALS.
CAUTION
Before Starting

10
No Contents Refer to
#2 in 1 Key
CFrom two 1-sided originals, side by side, to 1-sided copies. Page 16
$2 Page Copy Key
CCopying two facing pages on a ledger size original on two separate
letter size sheets. Page 17
%Sort Key
CWhen using Electric Sorting Mode.Optional memory is required. Page 20
&Margin Key
CShifts the image to the right or left. Page 18
(Edge Key
CCreates a blank edge. Page 18
)Book Key
CEliminates dark inner binding shadows. Page 18
*Original Mode Select Key (Photo;Text/Photo;Text) Page 12
+Exposure Keys (Darker, Lighter) Page 12
.Function Key
CUse when changing the paper size, initial values for functions (default
values) and key operator settings. Pages 25– 34
-SET Key
CSet the present selection. ——
Control Panel
NOTE
CThe Control Panel displayed above shows only copier functions.Please refer to the
operating instructions in the Panasonic Document Management System CD-ROM for
the Printer control panel functions.
/Clear Key
CClears the copy count in the display. ——
0Energy Saver Key
CCan save power while the copier is not in use. Page 21
1Reset Key
CResets all features to the initial power-on state. ——

11
 
Control Panel
LCD Display
Warning Indications
JAdd Paper
?AddToner
IMisfeed
2Call Service
No Contents Refer to
2Stop Key
CStops the copy run. ——
3Start Key
CUsed to start an operation. ——
4Interrupt Key, Memory In Key, M1/M2 Keys Pages 19 – 21
5Cursor Keys
CSelect copy ratio and function modes using (Gor F). ——
6PaperTray Key
CUsed to select the paper tray manually. ——
7Copy Size Key
CUsed to select Reduction/Enlargement only.For additional details,
see page 13. ——
8Original Size Key
CUsed to select the original size manually.For additional details,
see page 13. ——
9Print Key
CWhen selecting the Printer ON/OFF Line. ——
NOTE
CThe Control Panel displayed above shows only copier functions.Please refer
to the operating instructions in the Panasonic Document Management
System CD-ROM for the Printer control panel functions.
Before Starting

12
 
Basic Copy
Full Size Copying
■■
■■
■Copying the Same Size Originals (1:1)
Copy size is automatically selected.
1
Place the Original LCD Display (Sample)
Original Size Key
Select the Original Size on units
without the ADF Option.
NOTE
Clear Key 2
Number of Copies*
Up to 999 3
Press START**
#Select the original type
Photo :Originals are mainly composed of photo.
Text/Photo:Combined originals with text and photo.
Text :Originals are mainly composed of text.
$Select exposure control
Press the Darker/Lighter keys to adjust the exposure.
■■
■■
■Manually Selecting Exposure Control or OriginalType
∗Use Clear key when canceling the copy count.
∗∗ While the copier is warming up, you may position your original on the copier, enter
your copy job selections and press the Start key.The COPY JOB RESERVED
indicator displays until the warm up cycle is completed and the copy job will
automatically start.
READY TO COPY
COPIES:001

13
 
■■
■■
■Copying with Preset Ratios
Basic Copy
100 77 65 50
121 100 79 61
129 100 100 65
200 155 129 100
Reduction or Enlargement Copying
LDR ->LTR B [LTR B ]
ZOOM: 65% COPIES:001
Reset
Making Copies
1
Place the
Original
2
Select the
Original Size 3
Select the Copy
Size 4
Number of
Copies
CIf the desired copy size is different from the paper size loaded in the paper
tray, use the sheet bypass.(See page 15)
CPress the RESET key to cancel all job settings.
5
Press START
Example:Reduction
Original size Copy size
LEDGER LETTER
The correct ratio is automatically selected.
Reduction and enlargement ratios (%)
Original
size Copy size
Ledger Legal Letter Invoice
Ledger
Legal
Letter
Invoice
CWhen changing the paper tray, touch the
PaperTray key.
NOTE

14
 
NOTE
ATTENTION
■■
■■
■Zoom
Copies with variable zoom ratios from 50% to 200% in 1% increments.
LTR ->LTR B [LTR B ]
ZOOM:125% COPIES:001
B
Reset
Zoom Copying
Basic Copy
(Example: 125% Zoom)
1
Place the
Original 2Press Cursor (Gor F)
keys to select Zoom Ratio 4
Number
of Copies 5
Press
START
CWhen changing the paper size after setting the zoom ratio, please use the paper tray
key.
CPress the RESET key to cancel all job settings.
3
Select Original Size
(without using ADF)

15
NOTE
ATTENTION
Sheet Bypass
#Place the sheets of paper into
the tray. (approximately up to
50 Letter size sheets/20 lb)
Basic Copy
Using the Sheet Bypass
■■
■■
■Copying on Special Paper, etc.
1Place the original.
Open the sheet bypass.
2Pull out the sheet bypass tray
until it stops.
(For Ledger size only)
3
Insert the paper until it stops.
$Adjust the side guides.
Incorrect adjustment may cause the
paper to wrinkle, misfeed or skew.
PressSTART.
Side Guides
CAdjust the side guides properly to avoid skewing, wrinkling or misfeeding.
CDo not feed curled paper through the sheet bypass to avoid misfeed.
Do not fill above.
Making Copies

16
 
2 in 1 Copy
■2 in 1 Copy
From two 1-sided originals, side by
side, to 1-sided pages.
Creative Features
1\2 (Layout)*
2\1 (Layout)*
Portrait(Orientation)*
Landscape(Orientation)*
1\2 (Layout)*
2\1 (Layout)*
4
Number of
Copies
■■
■■
■Procedure
ADF
Face-Up
1
Place the
Originals 2
Press 2
in 1 key (3)
Copy Size
(Reduction/
Enlargement
Only)
5
Press
START
CThe ADF is required for 2 in 1 copy.
CPress the RESET key to cancel all job settings.
∗The Orientation and Layout can be set in the function mode.(See page 27)
NOTE

17
NOTE
 
CTo reset all job settings, press the RESET key.
3
Original Size
(Letter or Ledger
size Only)
4
Number of
Copies 5
Press
START
Platen Ledger size original
Letter
Book Mark
■2 Page Copy
Copying two facing pages on a ledger size
original on two separate letter size sheets.
■■
■■
■Procedure
1
Place the
Originals
2
Press the 2
Page Copy
key
2 Page Copy
Creative Features
Making Copies
Center book
by length
and width
according
to center
marks.

18
NOTE
Book/Edge/Margin
Creative Features
■Book Key
Eliminates dark inner binding shadows when copying from a book.
■Edge Key
Creates a blank edge.
■Margin Key
Shifts the image to the right or left.
 
■■
■■
■Procedure
∗Initial setting (Factory setting) can be changed in the User Mode function.
(See page 27)
∗∗ If a part of the copied image is missing when using the Margin mode, change the
Frame Reduction setting to ON.
(See page 27)
CPress the RESET key to cancel all job settings.
Book ∗Initial setting (Factory setting):20 mm
∗Initial setting (Factory setting): 5 mm and Equal Rate
∗Initial setting (Factory setting):10 mm and Left Margin
Edge
Margin**
1
Place the
Original 2
Press Book, Edge or
Margin key 5
Press
START
4
Number
of Copies
BOOK MARGIN
CENTER VOID = 20mm ∨∧
EQUAL RATE
VOID MARGIN = 5mm ∧
LEFT MARGIN
10mm ∨∧
3
Press Cursor (Gor F) keys to adjust
the void width while the button is
blinking.(approx.5 sec.)
CVoid/Margin width:5-99 mm

19
NOTE
Creative Features
Job Memory
 
Making Copies
■■
■■
■Two Copy Jobs Can Be Programmed in Memory (M1, M2) for recall at a
later time.
To store a job in memory
#Set up the copy job to be stored in memory,
by first selecting each function you wish the
copier to perform.
$Press the Memory In (F2) key.
%Press the M1 (F3) or M2 (F4) key.
To recall a job stored in memory
&Place the Original
(Press the M1 (F3) or M2 (F4) key.
The stored contents will be displayed.
)Press START
CStored job(s) will not be deleted even if the power switch is turned Off.
CWhen storing a new job into programmed memory, the previously stored job
will be overwritten.
JOB MEMORY
PRESS M1,M2 TO STORE.
RECALL JOB MEMORY
LOADING...