Panasonic EH-ND63 User manual

Order Number PEWT1610A20CE
(Household) Hair Dryer
Model No.
EH-ND63
Asia
CIS
Middle East
TABLE OF CONTENTS
PAGE
1 Warning -------------------------------------------------------------------------------
2
2 Specifications ----------------------------------------------------------------
2
3 Troubleshooting Guide ---------------------------------------------------
3
4 Disassembly and Assembly Instructions --------------------------
4
4.1 Disassembly instruction-------------------------------------------
4
4.2 Assembly Instructions---------------------------------------------------
5
5 Wiring Connection Diagram-------------------------------------------------------
6
6 Schematic Diagram ----------------------------------------------------------------
7
7 Exploded View & Replacement Parts List -------------------------------------
8
7.1 Exploded View for EH-ND63 -----------------------------------------------
8
7.2 Parts List for EH-ND63 ------------------------------------------------------
9
© Panasonic Corporation 2016 Unauthorized copying
and distribution is a violation of law.

1. Warning
Caution:
- Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40℃) higher.
Please use a oldering iron with temperature control and adjust it to 750 ±20°F (400 ± 10 ℃).
In case of using high temperature soldering iron, please becareful not to heat too long.
- Pb free solder will tend to splash when heated too high (about 1100°F / 600℃).
Power source AC 220-240 V 50-60 Hz
Power consumption Approx. "3" Turbo 220 V ~ 1700 W
230 V ~ 1850 W
240 V ~ 2000 W
Air volume without nozzle 1.45 m3/min
Air flow temperature ("3" Turbo) 90 K (in case of room temperature 30°C)
Dimensions (W) 80 x (D) 170 x (H) 260 mm
Cord length L = 1.7 m
Weight Approx. 350 g ( Without cord and Without Nozzle )
Supplied accessory EH-ND63 Set nozzle
2. Specifications

3 TROUBLESHOOTING GUIDE
Refer to WIRING CONNECTION DIAGRAM.
< TROUBLE >
< CHECK >
< REMEDY >
Main Body does not
operate
<CHECK POWER CORD>
Check the conductivity of POWER CORD.
<CHECK MAIN SWITCH>
Check the conductivity between the terminal 1
and 4 by setting the main switch at Position 1.
(Figure 1)
Replace the MAIN
SWITCH
Replace the MOTOR
HEATER ASSEMBLY
NG
Figure 1
OK
NG
OK
Hot Air is not emitted <CHECK MAIN SWITCH>
Check the conductivity between the terminal 2
and 4 by setting the main switch at Position 2
(Figure 2)
Replace the MAIN
SWITCH
NG
OK
Figure 2
<CHECK HEATER BLOCK>
Check if there are foreign objects on the joint
of the thermo switch (Figure 3)
Remove the foreign
objects on the joints
OK
NG
Replace the MOTOR
HEATER ASSEMBLY
Replace the MOTOR
HEATER ASSEMBLY
Thermo switch
Lead Wire (
Lead Wire ( Red)
Lead Wire ( White)
Lead Wire ( Green)
Lead Wire ( Brown-Cod)
Lead Wire ( Black)
Lead Wire ( Red)
Lead Wire ( White)
Lead Wire ( Green)
Lead Wire ( Brown-Cod)
Figure 2

4. Disassembly and Assembly Instructions
4.1. Disassembly Instructions
(1) Take off NOZZLE as same direction as below. (4). Take off HANDLE AB then take out
CLICK RING and SWIVEL RING
method as below.
(2). Remove 2 TAPPING SCREWS at HOUSING A (5). Take off HOUSING A method as below.
by flat-blade screwdriver and 2 TORX SCREWS
at HANDLE by Driver.
(3) Take off an AIR OUTLET GRILL (6). Take off a MOTOR HEATER ASSEMBLY
and an AIR OUTLET RING by rotating method as below. method as below.
Torx Screws
Tapping Screws
Counter clockwise rotation

4.2 Assembly Instructions
(1) Install MOTOR HEATER ASSEMBLY (4) Insert an AIR OUTLET GRILL
into HOUSING A as below drawing.
into an AIR OUTLET RING by fix position as below.
(2) Install HOUSING A method as below. (5) Insert an AIR OUTLET RING into Main Body
by fix position as below.
(3) Install SWIVEL RING on HANDLE A (6) Tightening screw both 2 TORX SCREWS
and install CLICK RING on HOUSING A and TAPPING SCREWS as below.
then install HANDLE AB on HOUSING AB
method as below.
Small rib
Large rib
clockwise rotation
Torx Screws
Tapping Screws

5. Wiring Connection Diagram
CIS

6. Schematic Diagram
EH-ND63
CIS
Main Sw. 1-4 2-4 3-5
Off "0" X X X
Cool "1" O X X
Heat Protection "2" O O X
Turbo "3" O O O
Symbol Part name
Specification
Code : Code :
605/655/685/695/865 L/415/615/645/62B
C1 CAPACITOR
0.22 mF, 275V NOT USE
C2 CAPACITOR (FOR MOTOR)
0.1 mF, 50VDC
D1, D2, D3, D4 DIODE (BRIDGE) 400V, 2A
F TEMPERATURE FUSE 133°C, 250V, 15A
M MOTOR RS365SV-1988
Main Sw. MAIN SWITCH AC 250V/15A
TH THERMO SWITCH 90 ± 5 °C
RHA HEATER COIL A
77.5 ± 2.35 W
RHB HEATER COIL B
77.5 ± 2.35 W
RHD HEATER COIL D
115.0 ± 3.5 W
TH THERMO SWITCH 90 ± 5 °C
R1 RESISTOR (R1)
27.0 kW
R2 RESISTOR (R2)
3.3 MW
R3 RESISTOR (R3)
1.0 MW
Option for Code

7 EXPLODED VIEW & REPLACEMENT PARTS LIST
7.1. Exploded View for : EH-ND63
CIS
6
1
2
10
12
11
5
1
3
4
2
13
9
8
7

7.2 Parts List for EH-ND63
Safety
Ref.
No.
Part No. Part Name & Description Q'ty Remarks
1 EHND63HSPW HOUSING AB (ROUGE PINK) 1 FOR OTHER
1 EHND63HS41PW HOUSING AB (ROUGE PINK) 1 FOR -P415 : INDONESIA
1 EHND63HS64PW HOUSING AB (ROUGE PINK) 1 FOR -P645 : VIETNAM
1 EHND63HS68PW HOUSING AB (ROUGE PINK) 1 FOR -P685 : UAE
1 EHND63HS69PW HOUSING AB (ROUGE PINK) 1 FOR -P695 : KUWAIT
1 EHND63HS86PW HOUSING AB (ROUGE PINK) 1 FOR -P865 : RUSSIA
2 EHND63HDPW HANDLE AB (ROUGE PINK) 1
3 EHND63T3012W TORX SCREW 3.0*12 (BLACK) 2
4 EHND63CRTW CLICK RING (WHITE) 1
5 EHND63SRTW SWIVEL RING (NATURAL) 1
6 EHND63MHB2W MOTOR HEATER ASSEMBLY 1 PLUG B2, FOR -P415/-P615/-P62B/-P645 : Include 5 Insulation Tubes
6 EHND63MHS3W MOTOR HEATER ASSEMBLY 1 PLUG S3, FOR -P605/-P655/-P685/-P695 : Include 5 Insulation Tubes
6 EHND63MH86W MOTOR HEATER ASSEMBLY 1 PLUG B2, FOR -P865 : Include 5 Insulation Tubes
7 EHND63AORHW AIR OUTLET REGULATOR (GRAY) 1
8 EHND63AOGW AIR OUTLET GRILL (BLACK) 1
9 EHND63AORW AIR OUTLET RING (CLEAR) 1
10 EHND63SNZPW SET NOZZLE (ROUGE PINK) 1
11 EHND63MSW MAIN SWITCH 1 Include 5 Insulation Tubes
12 EHND63MSPPW MAIN SWITCH PLATE (ROUGE PINK) 1
13 EHND63T2004W TAPPING SCREW 2.0*4 (BLACK) 1
- EHND6322S03W OPERATING INSTRUCTIONS 1 FOR -P605 : KONG KONG
- EHND6341S03W OPERATING INSTRUCTIONS 1 FOR -P415/-P62B/-P645/-P655 : INDONESIA/ INDIA/ VIETNAM/ MALAYSIA
- EHND6368S03W OPERATING INSTRUCTIONS 1 FOR -P615/-P685/-P695 : UAE/ KUWAIT
- EHND6386S03W OPERATING INSTRUCTIONS 1 FOR -P865 : RUSSIA
- EHND63S415PW INDIVIDUAL PACKAGE ASSEMBLY 1 FOR -P415/-P645 : INDONESIA/ VIETNAM
- EHND63S615PW INDIVIDUAL PACKAGE ASSEMBLY 1 FOR -P605/-P615 : HONG KONG/ UAE
- EHND63S62PW INDIVIDUAL PACKAGE ASSEMBLY 1 FOR -P62B : INDIA
- EHND63S655PW INDIVIDUAL PACKAGE ASSEMBLY 1 FOR -P655 : MALAYSIA
- EHND63S685PW INDIVIDUAL PACKAGE ASSEMBLY 1 FOR -P685 : UAE
- EHND63S695PW INDIVIDUAL PACKAGE ASSEMBLY 1 FOR -P695 : KUWAIT
- EHND63S865PW INDIVIDUAL PACKAGE ASSEMBLY 1 FOR -P865 : RUSSIA
Remarks : *1 Individual Available