Panasonic EH-ND52 User manual

© Panasonic Electric Works (Thailand) Co., Ltd.
2011. All rights reserved. Unauthorized copying and
distribution is a violation of law.
Order Number PEWT1104A17CE
Hair Dryer
Model No. EH-ND52
ASIA
TABLE OF CONTENTS PAGE PAGE
1 Warning-------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------10
6 Schematic Diagram---------------------------------------------11
7 Exploded View and Replacement Parts List -----------12

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typical the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide
Refer to WIRING CONNECTION DIAGRAM.

4
4 Disassembly and Assembly Instructions
4.1. Disassembly instruction
1. Take off nozzle as same direction in figure 4.
2. Remove tapping screws by Plus Driver and 2 torx screws by IEC driver as figure 5.

5
3. Take off an air outlet grill and an air outlet ring by rotating.
Take off an air inlet ring by rotating, then pulling a rear cover as figure 6.
4. Take off a handle A from housing A and B as figure 7.

6
5. Take off a housing A from a housing B .
Then remove tapping screws and a power cord retainer from handle B as figure 8.
6. Take off a motor heater block from a housing B as figure 9.

7
4.2. Assembly instruction
1. Install leadwire Black, Yellow, Violet, Orange and lead wire brown (from power cord) with a main switch and a capacitor as fig-
ure 10.
2. Connecting and soldering a motor heater block with a main switch as figure 11.

8
3. Assemble motor heater block with handle B and housing B as figure 12.

9
4. Assembly handle A , screw and nozzle as shown figure 13.

10
5 Wiring Connection Diagram

11
6 Schematic Diagram

Model No. : EH-ND52 Exploded View
7 Exploded View and Replacement Parts List

Model No. : EH-ND52 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 EHND52T0312W TORX SCREW 3*12 2 FOR HANDLE AB *1
2 EHND52HDWW HANDLE AB (WHITE) 1
3 EHND52MSPWW MAIN SWITCH PLATE (WHITE) 1
4 EHND52MSW MAIN SWITCH 1 INCLUDE 2 INSULATION TUBES (FOR CODE 615
,645)
4 EHND52MS2W MAIN SWITCH 1 INCLUDE CAPACITOR, 4 INSULATION TUBES (F
OR CODE 655,685)
5 EHND52T2005W TAPPING SCREW 2.0*5 2 FOR HOUSING AND REAR COVER *1
6 EHND52HSNW HOUSING AB (FLOWER CHAMP.GOLD) 1 FOR CODE N Series
6 EHND52HSVW HOUSING AB (FLOWER META.VIOLET) 1 FOR CODE V Series
7 EHND52SRTW SWIVEL RING 1
8 EHND52NZYW NOZZLE (TRANS.YELLOW) 1 FOR CODE N Series
8 EHND52NZVW NOZZLE (TRANS.VIOLET) 1 FOR CODE V Series
9 EHND52AORW AIR OUTLET RING 1
10 EHND52AOGW AIR OUTLET GRILL 1
11 EHND52MHB2W MOTOR HEATER BLOCK 1 B2-PLUG,INCLUDE 2 INSULATION TUBES
11 EHND52MHS3W MOTOR HEATER BLOCK 1 S3-PLUG,INCLUDE 2 INSULATION TUBES
12 EHND52RCNW REAR COVER (CHAMP.GOLD) 1 FOR CODE N Series
12 EHND52RCVW REAR COVER (META.VIOLET) 1 FOR CODE V Series
13 EHND52AIRWW AIR INLET RING 1
14 EHND52T3080W TAPPING SCREW 3*8 2 FOR POWER CORD RETAINER *1
15 EHND52PCRBW POWER CORD RETAINER 1
- EHND52S03W INSTRUCTION BOOKLET 1
- EHND52615NW INDIVIDUAL PACKAGE 1 FOR CODE N615 (INDIA)
- EHND52615VW INDIVIDUAL PACKAGE 1 FOR CODE V615 (INDIA)
- EHND52645NW INDIVIDUAL PACKAGE 1 FOR CODE N645 (VIETNAM)
- EHND52645VW INDIVIDUAL PACKAGE 1 FOR CODE V645 (VIETNAM)
- EHND52655NW INDIVIDUAL PACKAGE 1 FOR CODE N655 (MALAYSIA)
- EHND52655VW INDIVIDUAL PACKAGE 1 FOR CODE V655 (MALAYSIA)
- EHND52685NW INDIVIDUAL PACKAGE 1 FOR CODE N685 (S'PORE,HONG KONG,KUWAIT,U
AE)
- EHND52685VW INDIVIDUAL PACKAGE 1 FOR CODE V685 (S'PORE,HONG KONG,KUWAIT,U
AE)