Panasonic NU-MX100P User manual

No. Model
Operating Instructions
Panduan
使用说明书
Multifunctional Steam
Sterilizer and Dryer
Pensteril dan Pengering Stim
Pelbagai fungsi
奶瓶消毒烘干一体机
Household use only
Kegunaan Rumah Sahaja
仅家庭用
Important safety instructions
Read carefully and keep for future reference
Panduan keselamatan penting
Baca dengan teliti dan simpan untuk rujukan masa depan
请仔细阅读本说明书并妥善保管
Model No.
型号 NU-MX100P

English
1. Introduction
This product kills harmful bacteria with high-temperature
steam and helps you to sterilize various kinds of baby feeding
supplies safely and quickly.
This product can hold 6 baby bottles of any brand and
any size, or even supersized baby bottles. Besides, it can
also accommodate other baby feeding products, such as
complementary food bowls, cups and spoons. This product has
multiple functions: warming milk, reheating foods, steaming
eggs, and sterilizing/drying baby bottles and utensils.
2. Feature Diagram
Lid Clamp
Body
Power Supply Cord
Measuring Cup (150 ml)
Base
Identification
Plate
Scale 1 2 3 4
Water 25 ml 55 ml 80 ml 110 ml
*The above illustrations are for reference only.
3. Specifications
Model Number: NU-MX100P
Power Source: 220 - 240 V ~ 50 - 60 Hz
Input power Steriliser: 550 W
Input power Dryer: 170 W
Outside dimensions (H x W x D): 373 mm x 304 mm x 232 mm
Weight (approx.): 2.5 kg
*Specifications subject to change without notice.
For the batch number (model number) and manufacturer,
refer to the identification plate of the product.
Eng-1

Eng-2
4. Usage
●Control Panel
Power Pad
(On/Off) Reheating/
Steam Pad Sterilizing/
Drying Pad Drying Pad
Warm-milk
Pad
Time-Increase
Pad Time-Decrease
Pad
Display
Window Sterilizing
Pad
●Follow as below steps before first using:
(1) Measure 90 ml water with the measuring cup (maximum
200 ml) and pour it into the water storage tank of the base.
(2) Place the body on the base and cover it with the lid.
(3) Insert the power supply cord, turn on the power supply,
press the Power Pad “ ” to activate the product.
(4) Press the Sterilizing Pad “ ” to start the sterilization mode.
(5) The product starts to generate steam when the water
temperature reaches 100℃, and automatically shuts
down when the water is completely boiled away.
(6) After sterilizing, allow to cool for 3 minutes, and then
disconnect the power and unplug.
(7) Remove the lid and the body, pour out the remaining
water in the water storage tank of the base, and dry the
product for normal use next time.
Milk Warming Function
(1) Measure 90 ml water with the measuring cup (maximum
200 ml) and pour it into the water storage tank of the base.
(2) Place the body on the base, put the container (baby
bottle, cup or bowl) with milk and water on a stable
place in the body, and then cover it with the lid.
(3) Turn on the power supply, press the Power Pad “ ”.
(4) Press the Warm-milk Pad “ ” , and then press the Pads
“” and “ ” to select the desired time of 3-15 minutes.
*The default setting to milk warming is 6 minutes.
(5) If there is no further operation in 3 seconds, it will enter
working state after a “Beep” sound.
(6) The product heats the water in the water storage tank
quickly to turn it into steam for heating. The product will
beep 3 times and the indicator will flash after the program.
Referential Time Chart for Warming Milk*
Water volume Milk volume Time for 5℃
cold milk
Time for 20℃milk at
room temperature
90 ml
60-120 ml 3 minutes 3 minutes
120-180 ml 5 minutes 3 minutes
180-270 ml 6 minutes 4 minutes
>270ml 7 minutes 5 minutes

English
*Data prepared by Panasonic with test conditions - ambient
temperature 25℃, one PP material 300 ml wide-neck bottle,
and indicated milk temperature and milk volume in chart.
Note:
You may turn off the product manually and take out the
baby bottle when the milk temperature is appropriate.
Drip the milk on the back of your hand to
test the temperature before feeding
Reheating/Steaming Function
(1) Measure 90 ml water with the measuring cup (maximum
200 ml) and pour it into the water storage tank of the base.
(2) Place the body on the base, put the container with food
(of proper volume) on a stable place in the body, and
then cover it with the lid.
(3) Turn on the power supply, press the Power Pad “ ”.
(4) Press the Reheating/Steam Pad “ ” to enter this
program, and press the Pads “ ” and “ ” to select
the desired time of 3-15 minutes.
*The default setting for reheating/steaming is 6 minutes.
(5) If there is no further operation in 3 seconds, it will enter
working state after a “Beep” Sound.
(6) The product heats the water in the water storage tank
quickly to turn it into steam for heating. The product will
beep 3 times and the indicator will flash after the program.
The food should not be heated for too long.
Sterilizing Function
(1) Measure 90 ml water with the measuring cup (maximum
200 ml) and pour it into the water storage tank of the
base.
(2) Place the body on the base, put the baby bottles, teats
and other small items to be sterilized in the body of the
product, and cover it with the lid.
(3) Turn on the power supply, press the Power Pad “ ”.
(4) Press the Sterilizing Pad “ ” to enter this program,
and the product will enter working state after a “Beep” if
there is no further operation in 3 seconds.
(5) The product will beep 3 times and the indicator will flash
after the water is dried up and the program finishes.
Note: The water storage tank of the base can hold water
up to 200 ml. It is recommended that at least 90
ml of water should be added. The more water is
added, the longer the working time will be. The
product can work for about 20 minutes at most
or until it automatically shuts down.
Referential Chart for Added Water and Approximate
Sterilization Duration*
Added water volume 90 ml 120 ml 150 ml 200 ml
Sterilization duration 7-10 mins 10-13 mins 12-17 mins 18-23 mins
Eng-3

*Data prepared by Panasonic with test conditions - ambient
temperature 25℃, three 250 ml wide-neck bottles and nipples,
three 250 ml narrow-neck bottles and nipples, and indicated
water volume in chart.
There is still residual heat on the sterilized
items when the product just finishes the work.
Pay attention to the residual heat before use.
Drying Function
(1) Place the body on the base, put the baby bottles, teats
and other small items to be dried in the body of the
product, and cover it with the lid.
(2) Turn on the power supply, press the Power Pad “ ” .
(3) Press the Drying Pad “ ” to enter this program, and
press the Pads “ ” and “ ” to select the desired time
of 40, 60 or 80 minutes.
*The default setting time for drying is 40 minutes.
(4) If there is no further operation in 3 seconds, it will enter
working state after a “Beep” Sound.
(5) The product will beep 3 times and the indicator will flash
after the program.
Sterilization/Drying Function
(1) Measure 90 ml water with the measuring cup (maximum
200 ml) and pour it into the water storage tank of the base.
(2) Place the body on the base, put the baby bottles, teats
and other small items to be sterilized/dried in the body
of the product, and cover it with the lid.
(3) Turn on the power supply, press the Power Pad “ ” .
(4) Press the Sterilizing/Drying Pad “ ” to enter this
program, and press the Pads “ ” and “ ” to select
the desired drying time of 40, 60 or 80 minutes.
*The default setting time for drying is 40 minutes.
(5) The product will start the sterilization mode after
3 seconds without further operation and a “Beep” sound.
After the water is dried up and the sterilization finishes,
the product will automatically enter the drying mode and
continue to work.
(6) The product will beep 3 times and the indicator will flash
after the program.
Note:
①
The water storage tank of the base can hold water
up to 200 ml. It is recommended that at least 90 ml
of water should be added. The more water is added,
the longer the working time will be. The product
can sterilize for about 20 minutes at most or until it
automatically enters the drying mode.
②The default drying time is 40 minutes, you can select
the above-mentioned time according to your needs.
There is still residual heat on the sterilized
items when the product just finishes the work.
Pay attention to the residual heat before use.
Eng-4

English
●Graphical operation steps
Measure water and pour
it into water tank
Press Power Pad
Press Function pad
Cover the lid
Place the body on the
base and set baby bottle
and utensils
Choose Time for Warm-Milk,
Reheating/Steam, Drying,
Sterilizing/Drying Functions
Automatically go working state without
further operation after 3 seconds
5. Maintenance
●Water to use
It is recommended to use pre-boiled or filtered water to
reduce the generation of scale.
●Cleaning water storage tank
It is recommended to descale the product every 1-2 weeks
to ensure it works at 100% efficiency. The citric acid and
white vinegar are good choices to descale the product, and
for the descaling method, you may refer to the instructions
on the package or just do as follows (the following heating
function does not include drying).
When using citric acid: Dissolve 1 packet (10g) of
citric acid in 150 ml of water, pour the solution into the
water storage tank of the base，press “Power” and press
“Reheating/Steam”, and let the product work for 1-2 mins.
Eng-5

Cut off the power supply and rest the solution in the tank
for 30 mins. Pour it out, rinse the tank thoroughly and dry.
When using white vinegar: Dilute 30 ml of white vinegar
with 120 ml of cold water, pour the solution into the
water storage tank of the base，press “Power”, press
“Reheating/Steam”, and let the product work for 1-2 mins.
Cut off the power supply and rest the solution in the tank
for 30 mins. Pour it out, rinse the tank thoroughly and dry.
●Cleaning air filter
The filter at the bottom of the base can be removed for
cleaning. After cleaning, re-install it on the base with the
silver side outward.
Before using citric acid, read the instructions
carefully. Do not touch eyes. Place it beyond
the reach of children.
6. Q & A
(1) What items can be put into the product for sterilization?
Generally, items that can withstand high temperature
above 100 °C and release no hazardous substance
after being heated can be sterilized (for details, refer to
the instructions of these items or consult professionals),
such as PP bottle, glass bottle, silicone bottle, pacifier,
teether, safe tableware made of safe materials.
(2) Is there any strict requirements for water quality?
Generally, for sterilization, purified water or treated
drinking water is recommended. Untreated tap water
has a lot of impurities and is more likely to produce
scale. This will increase the cleaning difficulty and may
affect the normal operation of the product.
(3) Why is the sterilization time too short?
The reason why the sterilization time is too short may be
the water added is too little. Generally, the recommended
minimum amount of water to be added is about 90 ml. It is
appropriate to maintain a sterilization time of 10-15 minutes.
(4) Why are there still water droplets on some items after
drying?
The drying effect will be affected if too many items are placed
or items are placed too densely or at improper angles. It
is recommended to sterilize and dry items in batches, or
appropriately increase the drying duration and frequency.
(5) Why are there still water drops on the inner wall of
Body (near the overlap between Lid and Body) after
drying cycle completes?
During the drying process, the water steam condenses
into water drops trapped in the overlap between Lid and
Body, and can’t be fully dried up. When Lid is opened,
some water drops slide down the inner wall of Body from
the overlap. The water condensation can be reduced by
longer drying duration.
Eng-6

English
Warning
●Read the Operating Instructions carefully before using the
product and keep it properly for future reference.
●Before sterilization, clarify the reliability of the item to
be sterilized, and make sure that it can withstand high
temperature above 100℃and release no hazardous
substance after being heated.
Precautions:
●Check whether the product is damaged and whether the
accessories are complete after package is removed.
●Make sure the product is placed on a smooth and steady
surface when working.
●When the product works under sterilization mode, boiling
hot steam will come out from the lid. Do not place any items
on the lid.
●Place the product beyond the reach of children.
●Do not open the lid during the sterilization process. If the
sterilization process is stopped within 6 minutes after it
starts, the item inside may not be sterilized fully.
●After use, cut off the power and pour out the remaining
water in the product.
Do not pour out the
remaining water
from the left air
outlet, which may
cause the water to
enter the base.
It should be
poured out
from the right
side of the
base of the
product.
●Do not sterilize any item without water.
●If the power supply cord is damaged or the machine
malfunctions, unplug the power plug immediately, and
do not make the defective product in working condition.
Immediately request your retailer for inspection or repair to
prevent danger.
●This product is not recommended for persons with
disabilities, sensory or mental disabilities or personnel
(including children) lack of relevant experience and
knowledge, unless there is person who guards their safety
to supervise and instruct them in the use of this product.
●Take care of children to ensure they will not play with this
product.
●Make sure water has been added before powering on the
product.
●It is forbidden to immerse the base in water.
●The product has the drying function, and the base is
designed with an air outlet. Avoid water entering the air
outlet, otherwise, components may be damaged.
Read the Operating Instructions carefully
and use this product correctly
Eng-7

1. Pengenalan
Produk ini membunuh bakteria berbahaya dengan wap
bersuhu tinggi dan membantu anda mensterilkan pelbagai
jenis kelengkapan penyusuan bayi dengan selamat dan
pantas.
Produk ini boleh memuatkan 6 botol bayi daripada pelbagai
jenama dan saiz, atau malah botol bayi bersaiz sangat
besar. Di samping itu, ia juga boleh memuatkan produk
penyusuan bayi yang lain, seperti mangkuk makanan, cawan
dan sudu pelengkap. Produk ini mempunyai pelbagai fungsi:
pemanasan susu, pemanasan semula makanan, pengukusan
telur dan pensterilan/pengeringan botol dan perkakas bayi.
2. Diagram Bahagian
Penutup Pengapit
Badan
Produk
Kord Bekalan
Kuasa
Cawan Penyukat (150 ml)
Tapak
Plat
Pengenalpastian
Kerak 1 2 3 4
Air 25 ml 55 ml 80 ml 110 ml
*Ilustrasi di atas ialah untuk rujukan sahaja.
3. Spesifikasi
Nombor Model: NU-MX100P
Sumber Kuasa: 220 - 240 V ~ 50 - 60 Hz
Kuasa input Pensteril: 550 W
Kuasa input Pengering: 170 W
Dimensi luar (P x L x T): 373 mm x 304 mm x 232 mm
Berat (anggaran): 2.5 kg
*Spesifikasi adalah tertakluk kepada perubahan tanpa notis.
Untuk nombor kumpulan (nombor model) dan pengilang,
rujuk kepada plat pengenalpastian produk.
May-1

Bahasa
4. Penggunaan
●Panel Kawalan
Pad Kuasa (Dihi-
dupkan/Dimatikan) Pad Pemanasan
Semula/Wap Pad Pensterilan/
Pengeringan Pad Pengeringan
Pad
Panaskan-susu
Pad Naikkan-
Masa
Pad Turunkan-
Masa
Tetingkap
Paparan
Pad
Pensterilan
●Ikuti langkah di bawah sebelum mula menggunakan:
(1) Sukat 90 ml air dengan cawan penyukat (maksimum 200
ml) dan tuangkan ke dalam tangki simpanan air tapak.
(2) Letakkan badan produk di atas tapak dan tutup dengan penutup.
(3) Masukkan kord bekalan kuasa, hidupkan bekalan kuasa,
tekan Pad Kuasa “ ” untuk mengaktifkan produk.
(4) Tekan Pad Pensterilan “ ” untuk memulakan mod pensterilan.
(5) Produk mula menghasilkan wap apabila suhu air mencapai 100℃dan
dimatikan secara automatik apabila air sudah mendidih sepenuhnya.
(6) Selepas pensterilan, biarkan produk menjadi sejuk selama 3 minit
dan kemudian putuskan sambungan kuasa dan cabut palam.
(7) Tanggalkan penutup dan badan produk, buangkan baki
air di dalam tangki simpanan air tapak dan keringkan
produk untuk kegunaan biasa pada masa akan datang.
Fungsi Pemanasan Susu
(1) Sukat 90 ml air dengan cawan penyukat (maksimum 200
ml) dan tuangkan ke dalam tangki simpanan air tapak.
(2) Letakkan badan produk di atas tapak, masukkan bekas
(botol, cawan atau mangkuk bayi) bersama susu dan
air di atas tempat yang stabil di dalam badan produk
tersebut dan kemudian tutup dengan penutup.
(3) Hidupkan bekalan kuasa, tekan Pad Kuasa “ ”.
(4) Tekan Pad Panaskan-susu “ ” dan kemudian tekan Pad “ ”
dan “ ” untuk memilih masa yang dikehendaki iaitu 3-15 minit.
*Tetapan lalai untuk pemanasan susu ialah 6 minit.
(5) Jika tiada operasi selanjutnya dalam masa 3 saat, ia
akan memasuki keadaan fungsian selepas bunyi “Bip”.
(6) Produk memanaskan air di dalam tangki simpanan air
dengan pantas bagi mengubah air tersebut menjadi
wap untuk tujuan pemanasan. Produk akan berbunyi
bip 3 kali dan penunjuk akan berkelip selepas program.
Carta Masa Rujukan untuk Memanaskan Susu*
Isipadu air Isipadu susu Masa untuk susu
sejuk 5℃
Masa untuk susu
20℃pada suhu bilik
90 ml
60-120 ml 3 minit 3 minit
120-180 ml 5 minit 3 minit
180-270 ml 6 minit 4 minit
>270ml 7 minit 5 minit
May-2