Panasonic Toughbook CF-F8EWDZZAM Manual

DFQX5697ZA HS1208-0
Fingerprint Reader
Model No. CF-F8/CF-W8/CF-T8 Series
Names and Functions of Parts ................. 2
Overview ..................................................... 4
Installation .................................................. 5
More Advanced Security ........................... 8
Useful Information ..................................... 9
Troubleshooting....................................... 13
Specifications........................................... 19
SUPPLEMENTARY INSTRUCTIONS

2
Names and Functions of Parts
Except the following, refer to the Operating Instructions for the computer.
(Appearance may differ, depending on models.)
Fingerprint Reader
Fingerprint Reader
<CF-F8 Series>
<CF-W8/CF-T8 Series>

3
This section explains how your fingerprints are enrolled and authenticated.
1Slide your finger toward yourself.
To prevent a reading error.
ASet the first joint of your index finger on the sensor as illustrated to the
right.
BSlide your finger toward yourself while keeping it in contact with the finger-
print sensor.
CSlide your finger down until the sensor is visible.
When the fingerprint sensor does not enroll or authenticate your finger-
print properly:
· You slid your finger too fast or too slow.
· Your finger was soiled or it has a scar on the surface.
· Your finger was wet or extremely dry.
· Your fingerprint does not have sufficient data for personal identification.
For further information, refer to “Troubleshooting (For Devices)”.
(Îpage 13)
We shall not be liable for any loss or damage whatsoever resulting
from your Fingerprint device or neglect of Fingerprint device use, or
any data loss resulting from such developments as Fingerprint au-
thentication device malfunctioning.
CAUTION
How to Use the Fingerprint Reader

4
Fingerprint’s Outline
The conventional security systems use ID/passwords and token devices such as
IC cards to authenticate users. Therefore the passwords and token devices are
exposed to the risk of being lost, stolen and hacking.
The Fingerprint authentication method uses user’s fingerprints instead of pass-
words for security authentication. You can use your fingerprints to start up your
computer and log on Windows.
We recommend you use the Fingerprint Reader in combination with the TPM
(Trusted Platform Module) to increase the security level of your computer.
Precautions
Security Functions
Fingerprint Authentication Technology does not guarantee complete authentication and
individual identification. Please acknowledge we shall not be liable for any loss or dam-
age whatsoever resulting from the use of, or inability to use your Fingerprint device.
The Fingerprint authentication method uses multiple fingerprints, encryption
keys, credentials data and passwords. You might not be able to use your data if
you lose fingerprints, keys, credentials and passwords, so keep them in a safe
place. For further information, refer to “Backup”. (Îpage 9)
General interaction with 3rd party applications: There is no guarantee that
there will not be any negative interaction with any 3rd party software, and
will not accept any responsibility for such an interaction.
Overview
Performed by the Computer Administrator Performed by each user
Step 4
User Fingerprint Enrollment
User’s Data
• Windows Logon Password
• Fingerprint
• Fingerprint Backup Password
• Power-on Password
Step 1
TPM Installation ( Installation Manual of
“Trusted Platform Module (TPM)”)
(If the TPM is not being used, skip this step.)
(If the TPM is not being used, skip this step.)
Step 2
Fingerprint Utility Installation
Step 3
TPM Fingerprint Utility Initialization
This manual describes Steps 2, 3and the initial part of Step 4.
For further steps, refer to the UPEK Protector Suite QL Help menu. (<Model with
Windows XP> Click [start] - [All Programs] - [Protector Suite QL] - [Help] / <Model with
Windows Vista>
Click (Start) - [All Programs] - [Protector Suite QL] - [Help])
Recommended Installation Procedure

5
Installation
Step 1 TPM Installation
Refer to on-screen manuals Installation Manual of “Trusted Platform Mod-
ule (TPM)”. (<Model with Windows XP> Click [start] - [Run], enter “C:\util\drivers\
tpm\README.pdf”, and click [OK]. / <Model with Windows Vista> Click (Start)
and input “C:\util\drivers\tpm\README.pdf”, and press
Enter
.)
If the TPM is not being used, skip this step.
Step 2 Fingerprint Utility Installation
Performed by the Computer Administrator.
1Log on to Windows as an Administrator.
2Close all other programs.
3<Model with Windows XP>
Click [start] - [Run], enter “C:\util\drivers\fngprint\install\
setup32.exe”, and click [OK].
<Model with Windows Vista>
Click (Start) and input “C:\util\drivers\fngprint\install\
setup32.exe”, and press
Enter
.
The “Protector Suite ∗.∗Setup” screen appears.
4Click [Next].
Installation starts. Follow the on-screen instructions.
5When the “Protector Suite ∗.∗has been successfully
installed.” message appears, click [Finish].
At the confirmation message, click [Yes].
The computer restarts.
6Log on to Windows as an Administrator.
The “Protector Suite QL Icon” appears in the notification area.
“Protector Suite QL Introduction” appears if you touch the sensor before en-
rolling fingerprints.
NOTE

6
Installation
Step 4 User Fingerprint Enrollment
Performed by each user.
1<Model with Windows XP>
Click [start] - [All Programs] - [Protector Suite QL] - [User
Enrollment].
<Model with Windows Vista>
Click (Start) - [All Programs] - [Protector Suite QL] - [User
Enrollment].
Carefully read the License Agreement, select “I Accept the terms of the Li-
cense Agreement” and click [OK].
Step 3 TPM Initialization
Performed by the Computer Administrator.
The “Invalid TPM status” message is displayed by the “Protector Suite QL Icon ”
in the notification area.
If the TPM is not being used, skip this step.
1Click on the “Invalid TPM status” message to start
“Advanced Security Initialization Wizard”.
Follow the on-screen instructions.
<Model with Windows XP>
If the “Invalid TPM status” message is not displayed, click [start] - [All Pro-
grams] - [Protector Suite QL] - [Control Center] - [System Settings] - [TPM] -
[Initialize TPM].
<Model with Windows Vista>
If the “Invalid TPM status” message is not displayed, click (Start) - [All
Programs] - [Protector Suite QL] - [Control Center] - [System Settings] - [TPM]
- [Initialize TPM].
NOTE
2Click [Next].
3Select an enrollment mode, and click [Finish].

7
There is a limit to the number of fingerprints for “Power-on Security”.
(Îpage 19)
We recommend you use the Power-on Security feature. This feature
prevents unauthorized access to the user’s computer at the BIOS level.
AWhen the “Power-on Security” screen appears, click [Manage Passwords...].
BSelect [Power-On] in [Password Types], and click [Set password...].
CEnter the password for “Power-on Security”, and click [OK].
DClick [Close].
EAdd a check mark for [Power-On] in [Password Types].
FEnter the password (step C), and click [OK].
GClick [Next].
· Follow the on-screen instructions.
Enroll at least two fingers. Even if one of them is injured, you can use an-
other one to access your account and secret data. For further information
about the enrollment, refer to “How to Use the Fingerprint Reader” (Î
page 3) and “Fingerprint Tutorial”. (<Model with Windows XP> Click [start]
- [All Programs] - [Protector Suite QL] - [Fingerprint Tutorial] / <Model with
Windows Vista> Click (Start) - [All Programs] - [Protector Suite QL] -
[Fingerprint Tutorial].)
NOTE
NOTE
· Enrollment to the biometric device
All enrolled fingerprints are stored directly in the fingerprint sensor. The
user data will be secured by the hardware protection keys obtained by the
fingerprint sensor. There is a limit to the number of fingerprints that can be
enrolled (Îpage 19). The number is displayed on the screen.
· Enrollment to the hard disk
All enrolled fingerprints are stored on the hard disk. Hardware protection of
the user data is not possible, but multiple users can enroll their fingerprints.
“User Enrollment” wizard starts. Follow the on-screen instructions.
Enrollment mode
You can make the configuration for the enrollment only once during this initial-
ization phase.

8
1Register the Supervisor Password.
You have to register the Supervisor Password to proceed to the next step.
If you have already registered the Supervisor Password, you can move on
to step 2after performing Ato C.
If you have not done this, have enrolled your fingerprint using Protector
Suite QL, and have already made Power-on Security effective, after step B,
your fingerprint authentication will be necessary.
ATurn on or restart the computer.
BPress
F2
several times while [Panasonic] boot screen is displayed soon after
the computer starts the startup procedure.
CSelect the [Security] menu.
DSelect [Set Supervisor Password], and press
Enter
.
EEnter your password in the [Enter New Password], and press
Enter
.
· The password will not be displayed on the screen.
· You can use up to 32 alphanumeric characters (including spaces).
· The case (upper/lower) is ignored.
·
To input numbers for the password, use the numbered keys on the keyboard.
· You cannot use
Shift
and
Ctrl
to input a password.
FEnter your password again in [Confirm New Password], and press
Enter
.
GIn [Setup Notice], press
Enter
.
2Enable the Embedded Security (TPM).
ASelect [Fingerprint Security Sub-Menu], and press
Enter
.
BSelect [TPM State:], and press
Enter
.
CSelect [Enable] and press
Enter
.
· Default setting: Disable
DPress
F10
, select [Yes], and press
Enter
to exit the Setup Utility.
More Advanced Security
You can increase your computer’s security level by setting the BIOS level de-
scribed in this section.
Performed by the Computer Administrator.

9
The file described below is necessary for recovering the Fingerprint authentica-
tion data. Back up this file periodically in a safe location such as removable disk
to avoid data loss resulting from some accidents. We recommend you to store
the file in a removable disk or network drive because the benefit of Fingerprint
authentication security can be reduced if you keep the file in the internal hard disk
drive.
The backup password described below is necessary for bypassing the Fingerprint
authentication. We recommend you set the backup password using the “User
Enrollment” wizard. If you do not define the backup password, you may lose your
data in case of authentication hardware failure.
File used by each user
· Backup user passport data
(Default name: <User Account>.vtp)
You need this file when you replace the embedded fingerprint chip, or the hard
disk drive, or when reinstalling Windows. This file contains the fingerprints,
encryption keys, and logon authentication data.
Password used by each user
· Backup Password for Enrollment
This backup password can be used in case of hardware failure to bypass the
fingerprint authentication.
The passwords other than those explained above are also used for security,
so do not lose them. For further information, refer to the UPEK Protector
Suite QL Help menu (<Model with Windows XP> Click [start] - [All Pro-
grams] - [Protector Suite QL] - [Help] / <Model with Windows Vista> Click
(Start) - [All Programs] - [Protector Suite QL] - [Help]).
How to Backup:
Select “Export” in “Import or Export User Data” to save the user data. (<Model with
Windows XP> Click [start] - [All Programs] - [Protector Suite QL] - [Control Center] -
[Import or Export User Data] / <Model with Windows Vista> Click (Start) - [All Pro-
grams] - [Protector Suite QL] - [Control Center] - [Import or Export User Data])
For further information, refer to the UPEK Protector Suite QL Help menu. (<Model
with Windows XP> Click [start] - [All Programs] - [Protector Suite QL] - [Help] / <Mod-
el with Windows Vista>
Click (Start) - [All Programs] - [Protector Suite QL] - [Help])
Backup
NOTE
CAUTION
Useful Information

10
Password Bank*1limitations: The following web pages and Windows ap-
plications cannot be supported.
· Web pages which are created by the following technologies:
- Web forms created on the fly using JavaScript.
- Web forms which looks as one form (ie logon field, password field), but in-
ternally created with two independent forms.
- There can be auto submit problems with web forms which do not have Sub-
mit button. All forms that you cannot submit with
Enter
will be entered by
Password Bank, but not submitted.
· Applications which do not use standard Windows controls and draw controls
by their own.
· This includes any Java based application.
*1 For information of these functions, refer to the UPEK Protector Suite QL
Help menu (<Model with Windows XP> Click [start] - [All Programs] -
[Protector Suite QL] - [Help] / <Model with Windows Vista> Click (Start)
- [All Programs] - [Protector Suite QL] - [Help]).
“Sensor Scrolling Feature” is not supported.
Handling & Maintenance
The enrolling and authentication sensitivity may decline under the condi-
tions below. Wipe off stains or moisture on the sensor surface with a soft
cloth.
· The surface of the fingerprint sensor is soiled with dust, skin oil, or sweat.
· The surface of the fingerprint sensor is wet as a result of moisture or conden-
sation.
Static electricity may also cause the sensor to malfunction. To make your
finger static-free, touch a metal surface before placing it on the fingerprint
sensor. Exercise caution against static electricity in winter and other dry
conditions.
Malfunction or damage may occur when:
· The fingerprint sensor surface was damaged by the strong rubbing of a solid
material, scratches, or being pecked with a pointed item.
· The sensor was touched with a finger soiled with mud, damaging the sensor
surface with a tiny substance, and staining the surface.
· The sensor surface was covered with a seal, or soiled with ink.
Limitations in Use
Useful Information

11
Deleting (Initializing) Owner’s Data
When you dispose of the computer or transfer the ownership, delete (initialize) the
owner’s data to avoid unauthorized access. To initialize the owner’s data, perform
steps 1 to 3.
In other cases, refer to the required steps.
1Disable Power-on Security
Performed by the Computer Administrator.
A<Model with Windows XP>
Click [start] - [All Programs] - [Protector Suite QL] - [Control Center].
<Model with Windows Vista>
Click (Start) - [All Programs] - [Protector Suite QL] - [Control Center].
· The “Fingerprint Control Center” screen appears.
BClick [Power-on Security].
CRemove the check mark from [Enable power-on security using fingerprints], and
click [OK].
DClick [Enroll or Edit Fingerprints].
· “User Enrollment” wizard starts. Follow the on-screen instructions.
EWhen the “User’s Fingers” screen appears, click [Next] without deleting finger-
print samples.
FClick [Manage Passwords...].
GSelect [Power-On] in [Password Types], and click [Unset password...].
HEnter the password for Power-on Security, and click [OK].
IClick [Close].
· Confirm that there is no item in [Password Types].
JClick [Next].
KClick [Next].
LClick [Finish].
· Follow the on-screen instructions.
The data enrolled in the fingerprint sensor is not image data. You cannot re-
store fingerprint image data from the data enrolled in the fingerprint sensor.
NOTE
2Delete Fingerprint Data
Performed by each user.

12
AClick [Delete].
· The “Swipe finger” screen will appear.
BSwipe user’s finger.
· If the authentication is successfully completed, the confirmation message
appears.
CClick [Yes].
· Confirm that all user’s data was deleted.
ALog on to Windows as an Administrator.
BClose all programs.
C<Model with Windows XP>
Click [start] - [Control Panel] - [Add or Remove Programs].
<Model with Windows Vista>
Click (Start) - [Control Panel] - [Uninstall a program].
D<Model with Windows XP>
Click [Protector Suite ∗.∗], and click [Change].
<Model with Windows Vista>
Double-click [Protector Suite ∗.∗], and click [Remove].
E<Model with Windows XP>
Select [Remove].
FSelect [Remove all Protector Suite ∗.∗data], and click [Next].
· Uninstallation starts. Follow the on-screen instructions.
GWhen the “Protector Suite ∗.∗has been successfully uninstalled.” message ap-
pears, click [Finish].
· At the confirmation message, click [Yes].
· The computer restarts.
3Uninstall Protector Suite
Performed by the Computer Administrator.
If the enrollment mode is set to “Enrollment to the hard disk” (Îpage 7), you
need to remove the fingerprints data after step 2.
Performed by the Computer Administrator.
A<Model with Windows XP>
Click [start] - [All Programs] - [Protector Suite QL] - [Control Center].
<Model with Windows Vista>
Clic
k (Start) - [All Programs] - [Protector Suite QL] - [Control Center].
BClick [Power-on Security].
CSelect the fingerprint, and click [Remove].
· Surely remove all of the fingerprints.
NOTE
Useful Information

13
Troubleshooting
When a problem occurs, refer to this page. If you still cannot troubleshoot the
problem, contact PANASONIC TECHNICAL SUPPORT.
(Enrollment and authentication is unavailable to an extremely minority of people
including those whose fingerprints give little data for personal identification.)
For Devices
The sensor does not
enroll or authenticate
my fingerprint.
Slide your finger correctly. (For further information
about enrollment and authentication, refer to “How
to Use the Fingerprint Reader” (Îpage 3) and
“Fingerprint Tutorial”. (<Model with Windows XP>
Click [start] - [All Programs] - [Protector Suite QL] -
[Fingerprint Tutorial] / <Model with Windows Vista>
Click (Start) - [All Programs] - [Protector Suite QL]
- [Fingerprint Tutorial])
The sensor enrolls or authenticates no fingerprint, or
performs authentication poorly, despite the correct
way of finger sliding when your finger is in any of the
conditions stated below:
· Rough skin, or injured finger (with a cut or a skin
inflammation)
· Extremely dry
· Soiled with mud or oil
· Fingerprint has been worn and has faded
· Wet with water or sweat
<You can improve enrolling and authentication
sensitivity by taking the following steps when any of
the conditions described above exists>
· Wash your hands or wipe them dry.
· Use a different finger for registration or
authentication.
· Treat your finger with a hand cream when it is
rough skin or dry.
Clean the fingerprint sensor. (For further information,
refer to “Handling & Maintenance” (Îpage 10))
The fingerprint sensor may be malfunctioning when it
continues to perform poorly after the steps described
above have been performed. Contact PANASONIC
TECHNICAL SUPPORT.

14
Troubleshooting
For Application
Sensor does not
work.
Exported passport can help you if you need to
replace the sensor.
· Log on to Windows as an Administrator.
You can always access the computer by using your
Windows log on password. In convenient mode,
any user can access the computer by using your
Windows log on password.
· To access “File Safe”, “Personal Safe”
“File Safe” can be always accessed by using the
“File Safe” backup password.
“Personal Safe” can be always accessed by using
the “Personal Safe” backup password.
· Other functions
Replace/Repair the sensor, then follow the
instructions in section “Replacing sensor”.
Some limited functions (e.g. deleting passport)
is available without a functional sensor. In case
of deleted operation, it is necessary to cancel
the fingerprint verification operation to get to the
password dialog.
User cannot use
enrolled finger.
(e.g. injury)
It is strongly recommended to enroll at least two
fingers to avoid this problem.
If you enrolled multiple fingers, simply use other finger.
If you only enrolled one finger that can be used, we
recommend to use the “Enroll or Edit Fingerprints”
wizard and enroll additional fingerprints.
If none of your enrolled fingers can be used, follow
this procedure:
ALog on to Windows as an Administrator.
You can always access the computer by using
your Windows log on password. In convenient
mode, any user can access the computer by
using your Windows log on password.
BUpdate the enrolled fingerprints.
To be able to fully use Protector Suite QL, you
need to have usable enrolled fingerprints. Enter
the “Enroll or Edit Fingerprints” wizard.

15
User cannot use
enrolled finger.
(e.g. injury)
(continued)
· If you do not use “Advanced Security”, you can still
enter using the Windows password.
· If you use “Advanced Security” with backup
password, you can enter using the backup
password.
·
If you use “Advanced Security” without backup
password, there is no other way to add a different
fingerprint. In this case we recommend either to
wait until your finger is usable again (e.g. the injury
heals), or to delete the passport (Use “Delete”
wizard) and then reenroll new fingerprints. Please
note that in the latter case all your stored secret data
(passwords, “File Safe” encryption keys “Personal
Safe” data) will be lost. To perform the delete
operation it is necessary to cancel the fingerprint
verification operation to get to the password dialog,
then enter your Windows log on password.
· To access “File Safe”, “Personal Safe”
If you did not perform the procedure in step Bor
it did not work, you can still access “File Safe” by
using the “File Safe” backup password, “Personal
Safe” by using the “Personal Safe” backup
password.
TPM failure. If you use “Advanced Security” with TPM (Trusted
Platform Module) and TPM is broken, erased or
disabled, the “Advanced Security” will not work
anymore. If you do not use the “Advanced Security”
backup password, follow the instructions “Starting
Over” (Îpage 18). Otherwise, if you use “Advanced
Security” backup password, you can follow these
steps:
AEnter the “Enroll or Edit Fingerprints” wizard using
the backup password.
BDisable “Advanced Security” and finish.
CAfter the TPM is repaired and enabled (or if you
only erased its contents) you can enter the “Enroll
or Edit Fingerprints” wizard again using your
finger and enable the “Advanced Security” with
TPM again.

16
Troubleshooting
Replacing sensor. If you need to replace a non-functioning fingerprint
reader, follow this procedure:
Enrollment to the hard disk:
If enrollment to hard disk is used, “Protector Suite
QL” has not stored any data on the device and
therefore has no problem to continue after you
replaced the sensor. However, in case you use the
Power-on security (Preboot Authentication), you may
need to use the “Enroll or Edit Fingerprints” wizard to
update the related data.
Enrollment to the device:
If the fingerprint have been enrolled to the device, a
new passport will be required. Follow the procedure
in the section “Starting Over” (Îpage 18).
Lost Advanced
Security backup
password.
To change the “Advanced Security” backup
password, go to the “Enroll or Edit Fingerprints”
wizard and swipe your finger and go through the
Fingerprint enrollment. On the Advanced Security
page you can change the backup password.
Protector Suite QL
reinstallation.
Uninstall Protector Suite QL (Îpage 12) before
reinstalling it. After uninstallation, reinstall Protector
Suite (Îpage 5).
During Protector Suite QL uninstallation, you can
select whether to delete the Protector Suite Data -
including passports.
To use password data or “Password Bank” data
after reinstalling Protector Suite QL, select [Leave
Protector Suite *.* data for later use]. After the new
installation, you will be able to use your data again.
If you select [Remove all Protector Suite *.* data],
you need to enroll fingerprint data again after
reinstalling Protector Suite QL.
In case of changing the Enrollment mode, reinstalling
Protector Suite QL is necessary.
Lost “File Safe”
backup password.
It is necessary to change the backup password for
“File Safe”, refer to the UPEK Protector Suite QL
Help menu.
(<Model with Windows XP> Click [start] - [All
Programs] - [Protector Suite QL] - [Help] / <Model
with Windows Vista> Click (Start) - [All Programs]
- [Protector Suite QL] - [Help])

17
Accessing “File Safe”
after Protector Suite
QL uninstallation.
“File Safe” data can be accessed only using
Protector Suite QL. If you accidentally uninstalled
Protector Suite QL, you have to reinstall it. If
passport data was not removed during uninstallation,
everything will work automatically including “File
Safe”. If the passport data was removed during
uninstallation, the “File Safe” will recognize that the
installation was changed and will offer to use the
backup password, instead.
Accessing “File Safe”
after computer crash.
If you have an exported passport, import it now so
you can access “File Safe” directly using fingerprints.
Otherwise you can access “File Safe” using the “File
Safe” backup password: “File Safe” will recognize
that the installation was changed and will offer to use
the backup password, instead.
Removing data from
the reader.
When enrollment to the device is used, passport
data is stored to the device. To remove it, go to
the “Delete” passport wizard and delete existing
passports, and then use the “Fingerprint Inspector”
to remove remaining fingerprints (e.g. left over from
previous installations).
In convenient mode, the “Fingerprint Inspector” does
not allow deleting the last fingerprint for an existing
passport and only user’s own fingerprints can be
deleted. Therefore it is necessary to delete passports
first.
“Lift Finger” is
displayed during
operation.
You can temporarily disable the fingerprint sensor
with the following procedure.
ARight-click the “Protector Suite QL” icon in the
notification area.
BSelect [Don’t Use Sensor].
The icon turns gray.
To enable the fingerprint sensor, proceed as follows.
ARight-click the “Protector Suite QL” icon in the
notification area.
BSelect [Use Sensor].

18
ALog on to Windows as an Administrator.
· You can always access the computer by using your Windows log on password.
In convenient mode, any user can access the computer by using the Windows
log on password.
BTry to export your passport to a file if you are planning to use your passwords,
secret keys or enrolled fingers in the future.
· If you exported your passport recently, this step is not required.
·
If biometrics authorization works and your finger is recognized, use “Import or Export
User Data” wizard, swipe your finger and continue according to wizard’s instructions.
· If biometrics authorization works, but your finger is not recognized, you can start the
“Import or Export User Data” wizard and export the passport even without using your
fingerprint. You need to cancel fingerprint dialog, and you will be prompted for a pass-
word. If you do not use “Advanced Security”, enter your Windows log on password.
Otherwise, enter your “Advanced Security” backup password.
CDeleting the passport.
· Use the “Delete” wizard. Please note that all your stored secret data (passwords,
“File Safe” encryption keys “Personal Safe” data) will be lost. If you backed up
the data, you can restore it in step E; otherwise it will be lost permanently. To
perform the delete operation it is necessary to cancel the fingerprint verification
operation to get to the password dialog, then enter your Windows log on
password or backup password.
DMake sure your fingerprint sensor is working.
·
Use the Tutorial wizard to verify that the fingerprint sensor works. If not, reboot and try
again. If it still does not work, please contact PANASONIC TECHNICAL SUPPORT.
ERestore or create passport.
· If you have a backup of your data, you can now use “Import or Export User
Data” wizard to restore your data. Otherwise you can create a new passport by
using the “Enroll or Edit Fingerprints” wizard.
Troubleshooting
Starting Over
If the specific solutions for your problem does not work, you can use these instruc-
tions as the last measure and start over. However, please note that you can lose
your data - passwords, secret keys and fingerprints.
If you used “Advanced Security” without a backup password. There is
no way to backup your data.
If biometrics authorization does not work, there is no way to backup
your data.
CAUTION

19
Specifications
Model No. CF-W8/CF-T8
Series
CF-F8 Series
Array Size 248 x 4 pixels 192 x 4 pixels
Image Size 248 x 360 pixels 192 x 512 pixels
Image Resolution 508 DPI
The number
of enrollment
fingerprints
Biometric
Device 21 15
Hard Disk No limit
The number of
fingerprint for
“Power-on Security”.
Biometric
Device 21 15
Hard Disk

© Panasonic Corporation 2008
Printed in Japan