Panasonic KX-TDE User manual

6/19/2012 1
Version1
Clearfly SIP Trunks Configuration Guide
PBX Platform: KX-TDE/NCP

6/19/2012 2
Version1
Overview
This document describes the configuration procedures required for the KX-TDE100/200/600 and
NCP500/1000 to make full use of the capabilities of Clearfly Type SIP Trunks Services.
The SIP trunks services of the TDE/NCP PBX are provided through virtual CO line cards (V-
SIPGW16) which are designed to be easily integrated into an Internet Telephony Service
provided by an ITSP (Internet Telephony Service Provider).
This guide describes the specific configuration items for the virtual SIP Gateway card in addition
to the PBX basic configuration related to SIP trunks functionality. It also describes basic Network
configuration to familiarize dealers with the network setup. It does not describe the purpose and
use of all configuration options on the virtual SIP Gateway card. For those details, see the KX-
NCP500/1000 and KX-TDE100/200/600 Programming Manual for Virtual SIP CO Line Card and
the KX-TDE100/200/600 and KX-NCP500/1000 Manuals available from Panasonic
Communication Solutions.
DSP card and Activation keys
The PBX has to be equipped with a DSP card in order to provide
communication between the TDM side of the PBX and the SIP trunks.
Activation keys for SIP-Trunks has to be installed in the PBX to provide the
SIP-trunks functionality
To check the number of activation keys installed into the PBX and add new licenses
please refer to Page 12 in this guide

6/19/2012 3
Version1
Architecture Overview
The following diagram illustrates simple VOIP networks connecting the TDE/NCP PBX:
The Case of Clearfly Setup: Clearfly will provide its services over the Public Internet
MPR IP Address 192.168.0.101
VOIP IP Address 192.168.0.102
Default GW192.168.0.1
sc.cfly.co
Po
rt Forwarding rules on the end router
:
Forward Port 35060 to MPR IP address
Forward Port Range12000~12127 to VOIP-DSP IP address

6/19/2012 4
Version1
Basic V-SIPGW16 Settings for Clearfly Trunks
1-Install the PBX Maintenance console into your PC
The maintenance console should be available to certified dealers; Dealers can get the
latest version of the UPCMC from www.btsdealer.com (UPCMC version 7.2.1.0 or
higher)
2- Connect to the PBX
oStart the UPCMC
oClick Connect and choose the method of connection using either LAN , RS-
232, Modem, or USB to Connect to your PBX for interactive configuration
** We will be using the LAN method throughout this guide**
Provide the IP address of the MPR card and the password of the INSTALLER Level

6/19/2012 5
Version1
oGo to 1-Configuration, 1-Slot, move your mouse over the MPR card and
select the card property
Make sure that the default gateway should be the end router LAN IP address
Make sure that you have a valid DSP-VOIP LAN address

6/19/2012 6
Version1
3- Installing V-SIP W16 card
oGo to 1-Configuration, 1-Slot, move your mouse towards the IPCMPR virtual
shelf and click on select shelf
Highlight the V-SIPGW16 card from the cards list in the left side
oDrag the VSIPGW16 card into the trunk portion of the virtual shelf by using
the PC mouse lift button
oRelease the Mouse lift button and click Yes on the dialogue box

6/19/2012 7
Version1
oTake the V-SIPGW16 card OUS in order to be able to enter the following
settings
4-Configuring the VSIP-GW16 card
a- Shelf Property settings: Move the computer mouse over the VSIPGW16 card and
choose Shelf property
The following settings are required for Clearfly SIP trunk services on the shelf
property:

6/19/2012 8
Version1
Click Apply and then OK to exit the shelf property settings screen.
b- Card Property settings:
oMove the computer mouse over the VSIPGW16 card and choose Card property
oClick on Common settings
oDNS Server IP address method is Manual
oProvide your ISP DNS serevers IP addresses. (Contact your ISP to obtain DNS IP addresses
if needed)

6/19/2012 9
Version1
oClick Apply and then OK
oClick Cancel on the card property- Virtual SIP gatewayscreen to exit this screen
c- Port Property settings:
Move the computer mouse over the VSIPGW16 card and choose port property
Basic Channel setup:
Please locate the Clearfly SIP Trunks account details from your Clearfly
account Welcome letter/email.. Sample is shown below..
These addresses are just
sample. Please use your ISP
providedinformation

6/19/2012 10
Version1
oMain tab:
According to the account info above, we need to configure the Basic Channel Port as follows:
“Please Note: the information above is just a sample, please locate your
account details in your Clearfly welcome letter/email”
1- Port 1 channel attribute = Basic channel
2- Provider name= Clearfly
3- SIP Server Name= “sc.cfly.co ”
4- SIP server port number =5060
5- SIP service Domain = “Blank”
6- Subscriber number = 1234567890 (Optional)
oAccount tab:
1- user name == 1234567890
2- Authentication ID== same as BTN & Username 1234567890
3- Password == Provided by Clearfly
To: New Customer
cc: support <[e-mail]>
Subject: Clearfly SIP Trunk Information:
Hello,
Your Clearfly SIP trunk is now active and has been provisioned as follows:
PBX IP: 1.2.3.4 NAT Fixed-Global IP address
Clearfly SIP Server: sc.cfly.co SIP Server Location
Transport: UDP/5060
Codec: G.711u & G.729a
RTP Payload Type: 101
DTMF Relay: RFC2833
Digits Transferred: Default is 10. Please respond if you'd like something different.
123.456.7890 has been routed to this trunk <-- DID/BTN /account username..
If you haveany questions about or problems with this trunk, our techs are available for test/turn-up from 8AM-5PM MST,
Monday-Friday at +1.866.652.7520.
Regards,

6/19/2012 11
Version1
oRegister Tab:
Changes from Default settings:
1- Register abilty== Enable
2- Unregister ability when port INS= Disable
oNAT Tab:
Same as default
oCalling Party tab:
Changes from Default settings:
1- P-asserted Identity Header = Enable
oCalled party Tab:
Same as default
oVoice/Fax Tab:
Changes from Default settings:
1- IP Codec priority (1st = G.729A, 2nd= G.711u, 3rd=None)
oRTP/RTCP Tab:
Same as default
oT.38, T.38 Option
Same as default
oDSP
Same as default
oSupplementry services:
Changes from Default settings:
1- CNIP (Receive) = Yes
Additional DID’s
Please set the channel attribute for number of ports depending on the number of
active SIP lines as”additonal channel for channel 1”
For example ,if there are 3 Simultaneous calls can be received on this trunk, the
number of V-SIPGW ports to be set as an”additonal channel for channel 1”will be
2
ports

6/19/2012 12
Version1
Essential PBX Configuration:
Please locate your DID information in the Clearfly Welcome letter
To Assign the DID numbers destinations, Go to 10-3.CO & Incoming CallDID table
Important note:
Make sure that you provide the 10 digits DID number in the DID number field to be able to
make use of the additional DID’s assigned by the Provider.
SIP trunks Activation keys:
1- The DSP card installed onto the PBX MPR Card has preinstalled number of SIP
trunks activation keys (DSP4 and DSP16 have 4 IP trunks and DSP64 has 16 IP
trunks)
2- To obtain additional activation keys, you need to purchase the appropriate
activation key codes (For IP Trunks) and access the Key Management System. You
can download the activation keys as an activation key file from the Key
Management System. To download the activation keys, enter the MPR ID number
shown on the IPCMPR Card in the PBX, and activation key number and registration
ID provided on each activation key code.
3- To check the Number of Activation Keys Installed into your system
Go to 1- Configuration, 1-Slot, click on Activation Keys (Top of the PBX image)
Clearfly

6/19/2012 13
Version1
Minimum System Software requirements:
UPCMC V7.2.1.0 or higher
NCP V5.0002 or higher
TDE 100/200 V5.0002 or higher
TDE600 V5.0002 or higher
Useful Hints:
1- Update your system software once the update is available through the Dealer
website to make use of added features and improved functionality
2- Update your PCMC (Maintenance Tool) with the latest version available on the BTS
website and through Panasonic Tech support department
3- Back up your configuration file with the Good known settings
4- Consult with your network administrator prior to installation to guarantee a smooth
setup for your system over the existing network
Important Notes:
1- Fax and Modem communication:
Clearfly doesn’t support Fax or Modem communication over their SIP trunks. Clearfly
always suggests using POTS line for these types of communication.
2- E911 :
Please Work Closely with Clearfly team to ensure that E911 service is configured and
tested properly