Panasonic PT-VX410Z User manual

Product Name : LCD Projectors
SPEC FILE
Product Number : PT-VX410Z
1/13
SFL13M009
As of October 2013. Specifications and appearance are subject to change without notice.

Specifications
Main unit
Power supply
Power consumption
LCDpanel Panel size
Display method
Pixels
Pixel configuration
Lens
Lamp
Screen size
Colors
Brightness*2
Center-to-corner uniformity*2
Contrast*2
Resolution
Scanning frequency HDMI
RGB
YPBPR(YCBCR)
Video/S-Video
Optical axis shift
Keystone correction range
Installation
Built-in speaker Size
Output power
Terminals HDMI IN
COMPUTER (RGB) 1IN
R, G, B
Y, PB(CB), PR(CR)
100–240 V AC, 50/60 Hz
100–120 V: 300 W, 220–240 V: 280 W
(0.4 W when Standby mode set to Eco*1, 1.3 W when Standby mode set
to Network, 9 W when Standby mode set to Normal)
16.0 mm (0.63 inches) diagonal (4:3 aspect ratio)
Transparent LCD panel (× 3, R/G/B)
786,432 (1,024 ×768) ×3, total of 2,359,296 pixels
Stripe
Manual zoom (1.6×), manual focus F1.60– 2.12, f15.30– 24.64 mm
230 W UHM lamp
0.76 –7.62 m (30–300 inches) diagonally, 4:3 aspect ratio
Full color (16,777,216 colors)
4,200 lumens (LAMP POWER: NORMAL)
85%
4,000:1 (full on/off, LAMP POWER: NORMAL, Iris on)
1,024 ×768 pixels (Input signals that exceed this resolution will be
converted to 1,024 × 768 pixels.)
fH: 15–80 kHz, fV: 50–85 Hz, dot clock: 162 MHz or lower
fH: 15–100 kHz, fV: 50–100 Hz, dot clock: 162 MHz or lower (Signals
exceeding the dot clock rate of 140 MHz are downsampled.)
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
9:1 (fixed)
Vertical: ±40°, horizontal: ±30° (when an WXGA signal is input)
(vertical ±30° when using AUTO)
Ceiling/desk, front/rear (menu selection)
4 cm (1-9/16 inches) (round) ×1
10 W (monaural)
HDMI 19-pin ×1, HDCP compatible
VGA (640 ×480)–WUXGA*4(1,920 ×1,200),
dot clock: 25.2 MHz–146.25 MHz; Audio signal: linear PCM
(sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz)
D-sub HD 15-pin (female) ×1
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B, R: 0.7 Vp-p, 75 ohms;
HD/VD, SYNC: high impedance, TTL (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal);
PB(CB), PR(CR): 0.7 Vp-p, 75 ohms
Throw ratio 1.2– 1.9:1
480i (525i): fH15.75 kHz; fV60 Hz,
576i (625i): fH15.63 kHz; fV50 Hz,
480p (525p): fH31.50 kHz; fV60 Hz,
576p (625p): fH31.25 kHz; fV50 Hz,
720 (750)/60p: fH45.00 kHz; fV60 Hz,
720 (750)/50p: fH37.50 kHz; fV50 Hz,
1080 (1125)/60i: fH33.75 kHz; fV60 Hz,
1080 (1125)/25p: fH28.13 kHz; fV25 Hz,
1080 (1125)/24p: fH27.00 kHz; fV24 Hz,
1080 (1125)/24sF: fH27.00 kHz; fV48 Hz,
1080 (1125)/30p: fH33.75 kHz; fV30 Hz,
1080 (1125)/60p: fH67.50 kHz; fV60 Hz,
1080 (1125)/50p: fH56.25 kHz; fV50 Hz,
1080 (1125)/50i: fH28.13 kHz; fV50 Hz
480i (525i)*3, 576i (625i)*3, 480p (525p)*3, 576p (625p)*3, 720 (750)/60p,
720 (750)/50p, 1080 (1125)/60i, 1080 (1125)/50i, 1080 (1125)/25p,
1080 (1125)/24p, 1080 (1125)/24sF, 1080 (1125)/30p, 1080 (1125)/60p,
1080 (1125)/50p
PT-VX410Z
LCD Projectors
As of October 2013 2/13
SFL13M009

VIDEO IN
S-VIDEO IN
AUDIO IN 1
AUDIO IN 2 / MIC IN
AUDIO IN 3
AUDIO OUT
SERIAL IN
LAN
Power cord length
Cabinet materials
Dimensions (W ×H×D)
Weight*7
Operation noise*2
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range*8
Dimensions (W × H × D)
Weight
Pin jack ×1, 1.0 Vp-p, 75 ohms
Mini DIN 4-pin ×1, Y: 1.0 Vp-p; C: 0.286 Vp-p, 75 ohms
M3 (L, R) ×1, 0.5 Vrms
M3 (L, R) ×1, 0.5 Vrms
Pin jack ×2(L/R ×1), 0.5 Vrms
M3 (L, R) ×1(monitor out: 0–2.0 Vrms, variable)
D-sub 9-pin (male) ×1, for external control (RS-232C compliant)
RJ-45 ×1, for network connection, 100Base-TX/10Base-T, compliant
with PJLink™
2.0 m (6 ft 7 in)
Molded plastic
352×98*5× 279.4*6mm
(13-27/32 × 3-27/32*5× 11*6inches)
Approx. 3.3 kg (7.3 lbs)
35 dB (Lamp power: Normal), 29 dB (Lamp power: Eco 1 / Eco 2)
0–40 ˚C (32°– 104°F) (At altitudes less than 1400 m, High altitude mode: OFF)
0–30 ˚C (32°– 86°F) (At altitudes of 1400 m to 2000 m, High altitude mode: HIGH1)
0–30 ˚C (32°– 86°F) (At altitudes of 2000 m to 2700 m, High altitude mode: HIGH2)
10%–80% (no condensation)
3 V DC (R03/LR03/AAA type battery × 2)
Approx. 7 m (23 ft) when operated from directly in front of the
signal receptor
44 × 105 × 19.5 mm (1-23/32 × 4-1/8 × 25/32 inches)
Approx. 63 g (2.22 oz) (including batteries)
Supplied accessories
Optional accessories
Replacement lamp unit
Replacement filter unit
Ceiling mount bracket
Ceiling mount bracket
Bracket assembly
)1×(kcolytiruceshtiwdrocrewoP
Wireless remote control unit (× 1)
Batteries for remote control (R03/LR03/AAA type × 2)
VGA cable (× 1)
Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring
and Control Software) (× 1)
ET-LAV300
ET-RFV300
ET-PKV100H (for high ceilings)
ET-PKV100S (for low ceilings)
ET-PKV101B
Early Warning Software ET-SWA100
Weights and dimensions shown are approximate. Specifications subject to change without notice.
*1When the Standby mode is set to Eco, network functions such as power on over the LAN network will not operate. Also, only certain com-
mands can be received for external control using the serial terminal.
*2Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
*4WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5With legs at shortest position.
*6Include protruding parts.
*7Average value. May differ depending on models.
*8Operation range differs depending on environments.
COMPUTER (RGB) 2IN/ 1OUT
R, G, B
D-sub HD 15-pin (female) ×1
(input/output selectable using on-screen menu)
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B, R: 0.7 Vp-p, 75 ohms;
HD/VD, SYNC: high impedance, TTL (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
PT-VX410Z
LCD Projectors
As of October 2013 3/13
SFL13M009

176 (6-15/16)
352 (13-27/32)
63
(2-15/32)
255 (10-1/32)
98
(3-27/32)
90
(3-17/32)
55
(2-5/32)
8
(5/16)
Dimensions
Terminals
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
1Computer 1 input
2Computer 2 input / computer 1 output
3HDMI input
4LAN connector
5Serial input
6Video input
7Audio input 3
8Audio input 1
9Audio input 2 / mic input
10 Audio output
11 S-Video input
12
7891011
34
56
279.4 (11)
PT-VX410Z
LCD Projectors
As of October 2013 4/13
SFL13M009

Standard setting-up position
unit : mm (inch)
NOTE:
Illustrations show the projector
installed using optional ceiling mount
bracket ET-PKV100H and bracket
assembly ET-PKV101B.
This illustration is not drawn to scale.
Caution:
•All construction work should be done by a qualified technician.
•When mounting to the ceiling, use the special mounting bracket. To prevent the projector from swaying or drop-
ping, attach the wire that is included with the projector between the mounting bracket and the ceiling.
0.76 m
1.02 m
1.27 m
1.52 m
1.78 m
2.03 m
2.29 m
2.54 m
3.05 m
3.81 m
5.08 m
6.35 m
7.62 m
30˝
40˝
50˝
60˝
70˝
80˝
90˝
100˝
120˝
150˝
200˝
250˝
300˝
/
/
/
/
/
/
/
/
/
/
/
/
/
Projection size
[diagonal]
Projection distance [L]
Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens [H]
Projection distance for 4:3 aspect ratio screen
unit: meters (feet)
NOTE:
.scitsiretcarahcsnelmoozehtnognidnepedylthgilsseirav)neercsotecnatsid(LrofeulavehT•
•At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
63 (2-15/32)
100
(3-15/16)200
(7-7/8)
70
140
(5-1/2)
70 (2-3/4)
(2-3/4)
100
(3-15/16)
125.5
(4-15/16)
Lower edge of projected image
Upper edge of projected image
Projected image
L
L
HH
ø38
(1-1/2)
840–1,410
(33-1/16–55-1/2)
Adjustable in
30-mm
(1-3/16-inch) step.
Projected image
L
153.9
(5-1/16)
(2.3)
(3.1)
(3.9)
(4.7)
(5.5)
(6.3)
(7.1)
(7.9)
(9.5)
(11.9)
(15.8)
(19.8)
(23.8)
0.7
0.9
1.2
1.4
1.7
1.9
2.2
2.4
2.9
3.6
4.8
6.0
7.3
1.1
1.5
1.9
2.3
2.7
3.1
3.5
3.9
4.7
5.8
7.8
9.7
11.7
0.05
0.06
0.08
0.09
0.11
0.12
0.14
0.15
0.18
0.23
0.31
0.38
0.46
(0.15)
(0.20)
(0.25)
(0.30)
(0.35)
(0.40)
(0.45)
(0.50)
(0.60)
(0.75)
(1.00)
(1.25)
(1.50)
(3.7)
(5.0)
(6.3)
(7.6)
(8.9)
(10.2)
(11.4)
(12.7)
(15.3)
(19.1)
(25.6)
(32.0)
(38.4)
PT-VX410Z
LCD Projectors
As of October 2013 5/13
SFL13M009

ecnatsidnoitcejorpehtfonoitaluclaC
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 4:3
minimum L (m) = (diagonal screen size in inches) × 0.0243 –0.0294
maximum L (m) = (diagonal screen size in inches) × 0.0391 – 0.0319
NOTE:
Distances calculated with the above equations will include a slight error.
Installable angle
Install the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical
angle of 40°.
• Horizontal direction
The projector may be installed at a horizontal
angle of 15°.
–15°
+15°
+40°
–40°
PT-VX410Z
LCD Projectors
As of October 2013 6/13
SFL13M009

List of compatible signals
The signals that can be input to this projector are shown in the table below. Horizontal scanning fre-
quencies of 15 kHz to 80 kHz(15 kHz to 100 kHz for RGB signals), vertical scanning frequencies of 50
Hz to 120Hz(50 Hz to 100 Hz for RGB signals), and a dot clock of 162 MHz maximum imum for RGB
signals) can be input.
NOTE: The native resolution of this projector is 1,024 × 768 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)*1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Format
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720(1440) × 480i*2
720(1440) × 576i*2
720 × 483
720 × 576
1280 × 720
1920 × 1080i
1920 × 1080
640 × 480
640 × 400
800 × 600
832 × 624
1024 × 768
1152 × 864
1152 × 870
1280 × 720
−
−
VIDEO/S-VIDEO
HDMI/RGB
*1The “i” appearing after the resolution indicates an interlaced signal.
*2Only compatible with dot clock frequency of 27 MHz (pixel repetition signal)
*3When a 1125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
NTSC/NTSC4.43/PAL-M/PAL615.7 59.9
PAL/PAL-N/SECAM 15.6 50.0
480i(525i)15.7 59.9 13.5
13.5
576i(625i) 15.6 50.0
480i(525i)15.7 59.9 27.0
27.0
27.0
27.0
HDMI
576i(625i)15.6 50.0
480p(525p) 31.5 59.9
576p(625p) 31.3 50.0
720(750)/60p 45.0 60.0
74.3
74.3
74.3
74.3
74.3
720(750)/50p 37.5 50.0
1080i(1125i)/60i*333.8 60.0
1080i(1125i)/50i 28.1 50.0
1080(1125)/24p 27.0 24.0
1920 × 1080i 74.3
1080(1125)/24sF 27.0 48.0
1920 × 1080 74.3
1080(1125)/25p 28.1 25.0
74.3
1080(1125)/30p 33.8 30.0
1080(1125)/60p 67.5 60.0 148.5
148.5
1080(1125)/50p 56.3 50.0
VESA400 31.5 70.1 25.2
37.9 85.1 31.5
VGA 31.5 59.9 25.2
35.0 66.7 30.2
37.5 75.0 31.5
31.5
37.9 72.8
43.3 85.0 36.0
SVGA 35.2 56.3 36.0
37.9 60.3 40.0
46.9 75.0 49.5
48.1 72.2 50.0
53.7 85.1 56.3
MAC16 49.7 74.6 57.3
XGA 39.6 50.0 51.9
48.4 60.0 65.0
56.5 70.1 75.0
60.0 75.0 78.8
65.5 81.6 86.0
68.7 85.0 94.5
80.0 100.0 105.0
MXGA 64.0 70.0 94.2
67.5 74.9
85.0
108.0
77.1 119.7
MAC21 68.7 75.1 100.0
1280×72037.1 50.0 60.5
44.8 60.0 74.5
YPBPR(YCBCR)/RGB
HDMI/
YPBPR(YCBCR)/RGB
PT-VX410Z
LCD Projectors
As of October 2013 7/13
SFL13M009

1280 × 768
1280 × 800
1280 × 960
1280 × 1024
1366 × 768
1400 × 900*2
1400 × 1050
1600 × 1200
1680 × 1050
1920 × 1080*2
1920 × 1200*2
1280 × 768
1280 × 800
MSXGA
SXGA
1366 × 768
1920 × 1080
SXGA+
WXGA+
UXGA
WSXGA+
WUXGA
Display mode Display
resolution
(dots)*1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Format
HDMI/RGB
60.3 74.9 102.3
68.6 84.8 117.5
41.2 50.0 69.9
49.7 60.0 84.7
1600 × 900
1600 × 900 46.3 50.0 97.0
55.9 60.0 119.0
60.0 60.0 108.0
64.0 60.0 108.0
80.0 75.0 135.0
91.1 85.0 157.5
39.6
75.0
50.0
60.0
60.0
60.0
69.9
65.2 122.6
82.2 155.9
59.955.5 88.8
60.047.7 84.7
75.0 162.0
65.2 146.3
66.6 59.9 138.5
74.0 60.0 154.0
*1The “i” appearing after the resolution indicates an interlaced signal.
*2VESA CVT-RB (Reduced Blanking)-compliant.
PT-VX410Z
LCD Projectors
As of October 2013 8/13
SFL13M009

Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
6
15
9
D-sub 9-pin (male)
Serial input
Description
NC
Receive data
Send data
NC
Ground
Signal name
–
RXD
TXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
CAUTION
•It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 sec-
onds, then try sending or receiving again.
•When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next
command.
•Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10
seconds or more.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte) Parameters
(undefined length)
Command
(3 bytes)
STX ETXC1 P1 P2 ... PnC2 C3 :
Signal level
Synchronization method
Baud rate
Parity
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
NOTE: When sending commands without parameters, a colon (:) is not necessary.
Basic format with sub-commands
Same as the basic format without sub-commands
Parameters (6 bytes):
“+” or “-” sign (1 byte) with setting/adjusting value (5 bytes)
Sub-command
(5 bytes)
Operation (1 byte):
“=” (Sets the value designated by the parameters)
S1 P1 P2 P3 P4 P5 P6S2 S3 S4 S5 E
STX ETXC1 C2 C3 :
Character length
Stop bit
X parameter
S parameter
8 bits
1 bit
None
None
NOTE: When sending sub-commands that require no parameters, operation (E) and parameters are not necessary.
PT-VX410Z
LCD Projectors
As of October 2013 9/13
SFL13M009

Cable specifications
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
PC (DTE)Projector
NC
NC
NC
NC
NC
NC
NC
NC
Control commands
PON*1/*2
POF*1
ORF*3
AVL:<pl>
IIS:<input signal>
VPM:STD
VPM:DYN
VPM:CIN
VPM:REA
VPM:BBD
VPM:CBD
VPM:IM1
VPM:IM2
VPM:IM3
VPM:IM4
AUU
AUD
Power on (standby mode on)
Power off (standby mode off)
Volume control
Input signal selection
Picture mode: Standard
Picture mode: Dynamic
Picture mode: Cinema
Picture mode: Real
Picture mode: Blackboard
Picture mode: Colorboard
Picture mode: Image 1
Picture mode: Image 2
Picture mode: Image 3
Picture mode: Image 4
Volume up
Volume down
PON
POF
ORF=1
AVL:<pl>
IIS:<input signal>
VPM:STD
VPM:DYN
VPM:CIN
VPM:REA
VPM:BBD
VPM:CBD
VPM:IM1
VPM:IM2
VPM:IM3
VPM:IM4
AUU
AUD
–
–
0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
63
–
––
–
–
–
–
–
–
–
–
–
–
–
–
eulavretemaraP>retemaraP<:kcabllaCnoitcnuF>retemaraP<:dnammoC
Min Max
*1Do not send PON, or POF commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replace-
ment cycle.
*2These commands are effective when the standby mode is set to eco. (Other commands are not effective.)
*3This command is only enabled when Computer 1 is selected.
If anything other than Computer 1 is selected, first transmit the “IIS:RG1” command, and then transmit this command.
Furthermore, RBG is always selected when the “IIS:RG1” command is transmitted.
YPBPR/RGB signal switching
PT-VX410Z
LCD Projectors
As of October 2013 10/13
SFL13M009

Status request commands
CommandDescriptionCallback
<Parameter>
QPW*
Q$S*
QIN
QAV
QPM
Q$L
Standby power status
Lamp status
Input signal status
Volume adjustment value
Picture mode status
Lamp run time
Standard
Dynamic
Cinema
Real
Blackboard
Colorboard
Image 1
Image 2
Image 3
Image 4
<power condition>
<lamp condition>
<input signal>
<pl>
STD
DYN
CIN
REA
BBD
CBD
IM1
IM2
IM3
IM4
<acctch>
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
Command example
To set the volume to +30, send the command as shown below.
STX AVL :30ETX
StartCommand Parameter End
NOTE: When sending commands without parameters, a colon (:) is not necessary.
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
Parameter format
Parameter format Size (Byte) Definition
<pl>
<off on>
<input signal>
<power condition>
<lamp condition>
<acctch>
3 (1 or 2 bytes also
possible when
under control)
1
3
3
1
4
Decimal without signs: 0 to 999 (000, 001, 002...999)
Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99)
Callback from the projector is 3 Byte.
0 = off, 1 = on
HD1 = HDMI, RG1 = computer 1, RG2 = computer 2, NWP = network
PA1 = memory viewer, MG1 = panasonic application, MV1 = Miracast,
VID = video, SVD = S-Video
000 = power off (standby mode off), 001 = power on (standby mode on)
0 = standby, 1 = lamp on under control, 2 = lamp on,
3 = lamp off under control
Decimal without signs: 0000–9999 hours
*These commands are effective when the standby mode is set to eco. (Other commands are not effective.)
PT-VX410Z
LCD Projectors
As of October 2013 11/13
SFL13M009

Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is the unobstructed space as shown below or more around the projector’s exhaust
openings. In addition to this space, also ensure that there is a sufficient work space for removing
and installing the lamp, filter and other parts.
3. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the pro-
jector so that cool or hot air from other air conditioning equipment does not flow directly toward the
projector’s air intake or exhaust openings.
4. Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
200 mm (7-7/8)
or more
500 mm (1 ft 8 in)
or more
1,000 mm (3 ft 3 in) or more
Direction of air intake and exhaust
Intake
Exhaust
PT-VX410Z
LCD Projectors
As of October 2013 12/13
SFL13M009

Operating the projector continuously
1. If the projector is to be operated continuously 12 hours or more, lamp replacement cycle duration
becomes shorter.
2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods (one hour or less).
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
Product availability differs depending on region and country. This product may be subject to export control regulations.
PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.
Microsoft®, Windows®, Windows Vista®and Internet Explorer®are all registered trademarks of Microsoft Corporation in the United States.
Apple, Macintosh, Mac, Mac OS and Safari are registered trademarks of Apple Inc. in the United States.
Miracast is a trademark or registered trademark of the Wi-Fi-Alliance.
All other trademarks are the property of their respective trademark owners.
PT-VX410Z
LCD Projectors
As of October 2013 13/13
SFL13M009