Panasonic PT-DW530 System manual

SPEC FILE
Product Number : PT-DW530
Product Name : DLP™Projector
A of May 2011. Specification and appearance are ubject to change without notice.
SFD10M013-1
1/14

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
2/14
Specifications
Main unit
Power supply
Power consumption
DLP™ chip Panel size
Display method
Pixels
Lens
Throw ratio 16:10 aspect ratio
16:9 aspect ratio
Lamp
Screen size
Brightness*2
Center-to-corner uniformity*2
Contrast*2
Resolution
Scanning frequency HDM /DV -D
RGB
YPBPR(YCBCR)
Video/S-Video
Optical axis shift
Keystone correction range
nstallation
Terminals HDM N
DV -D N
RGB 1 N
R, G, B
Y, PB, PR(Y, CB, CR)
100–240 V AC, 5.0–1.9 A, 50/60 Hz
415 W (500 VA)
(0.3 W at 100–120 V AC, 0.4 W at 220–240 V AC with standby mode
set to eco*1, 15 W with standby mode set to normal. Both with fan
stopped.)
16.5 mm (0.65 inches) diagonal (16:10 aspect ratio)
DLP™ chip × 1, DLP™ system
1,024,000 (1,280 × 800) × 1, total of 1,024,000 pixels
Manual zoom (2× zoom), manual focus F 2.0–3.4, f 21.5–43.0 mm
1.53–3.09:1
1.53–3.09:1
300 W (max. 310 W) UHM lamp
1.02–7.62 m (40–300 inches), 16:10 aspect ratio
4,000 lumens (lamp mode: normal)
90%
2,000:1 (full on/full off)
1,280 × 800 pixels ( nput signals that exceed this resolution will be
converted to 1,280 × 800 pixels.)
fH: 27 kHz–100 kHz, fV: 24Hz–120 Hz, dot clock: 25 MHz–162 MHz
fH: 15 kHz–100 kHz, fV: 24Hz–120 Hz, dot clock: 162 MHz or lower
480i (525i): fH15.75 kHz; fV60 Hz,
576i (625i): fH15.63 kHz; fV50 Hz,
480p (525p): fH31.50 kHz; fV60 Hz,
576p (625p): fH31.25 kHz; fV50 Hz,
720 (750)/60p: fH45.00 kHz; fV60 Hz,
720 (750)/50p: fH37.50 kHz; fV50 Hz,
1035/60i: fH33.75 kHz; fV60 Hz,
1080 (1125)/60i: fH33.75 kHz; fV60 Hz,
1080 (1125)/50i: fH28.13 kHz; fV50 Hz,
1080/25p: fH28.13 kHz; fV25 Hz,
1080/24p: fH27.00 kHz; fV24 Hz,
1080/24sF: fH27.00 kHz; fV48 Hz,
1080/30p: fH33.75 kHz; fV30 Hz,
1080/60p: fH67.50 kHz; fV60 Hz,
1080/50p: fH56.25 kHz; fV50 Hz
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Vertical: +70% (manual), horizontal: ±10% (manual)
Vertical: ±40°
Ceiling/floor, front/rear
HDM 19-pin × 1, Deep Color, HDCP compatible
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 × 480)–WUXGA (1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25 MHz–162 MHz
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz,
32 kHz)
DV -D 24-pin × 1, DV 1.0 compliant, HDCP compatible, for single link
only480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 × 480)–WUXGA (1,920 × 1,200), compatible with non-
interlaced signals only, dot clock: 25 MHz–162 MHz
BNC × 5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD/VD, SYNC: High impedance, TTL (positive/negative)
N TE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms

SPEC FI L E
PT-DW530
D P™Projector
As of May 2011
SFD10M013-1
3/14
RGB 2 IN
R, G, B
Y, PB, PR(Y, CB, CR)
VIDEO IN
S-VIDEO IN
AUDIO IN 1
AUDIO IN 2
AUDIO IN 3
AUDIO OUT
SERIA IN
REMOTE IN
AN
WIRE ESS MODU E
Power cord length
Cabinet materials
Dimensions (W ×H×D)
Weight
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range*5
Dimensions (W × H × D)
Weight
Supplied accessories
Optional accessories
Replacement lamp unit
Ceiling mount bracket
Wireless module
D-sub HD 15-pin ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD/VD, SYNC: High impedance, TT (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR(CB/CR): 0.7 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
Mini DIN 4-pin × 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
RCA × 2 ( , R × 1), 0.5 Vrms
M3 × 1 ( , R × 1), 0.5 Vrms
M3 × 1 ( , R × 1), 0.5 Vrms
M3 × 1 ( , R × 1) (monitor out: 0–2.0 Vrms, variable)
D-sub 9-pin × 1 for external control (RS-232C compliant)
D-sub 9-pin × 1 for external control (parallel)
RJ-45 × 1 for network connection, 100Base-TX/10Base-T, compliant
with PJ ink™
Connector for optional wireless module ET-WM200U/WM200E ×1
3.0 m (9 ft 10 in)
Molded plastic (PC + ABS)
332 mm × 168 mm*3× 484.5 mm*4
(13-1/16˝ × 6-5/8˝ *3× 19-1/16˝ *4)
Approx. 8.5 kg (18.7 lbs)
0°–45°C (32°–113°F)
20%–80% (no condensation)
3 V DC (R6/ R6/AA type battery × 2)
Approx. 15 m (49 ft 3 in) when operated from directly in front of the
signal receptor
48 × 163 × 24.5 mm (1-13/32˝ × 6-5/8˝ × 31/32˝)
Approx. 117 g (4.1 oz) (including batteries)
Power cord with security lock (× 1)
Wireless remote control unit (× 1)
Batteries for remote control (R6/ R6/AA type × 2)
Wire rope (× 1)
Software CD-ROM ( ogo Transfer Software, Multi Projector Monitoring
and Control Software Ver. 2, Wireless Manager ME 5.5) (× 1)
ET- AD60A
ET- AD60AW (Twin Pack)
ET-PKD110H (for high ceilings)
ET-PKD110S (for low ceilings)
ET-WM200U (for North America)
ET-WM200E (for Europe and Asia)
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
*1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate. Also, only certain com-
mands can be received for external control using the serial terminal.
*2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*3 Compliant with VESA CVT-RB.
*4 With legs at shortest position.
*5 Including the lens.
*6 Operation range differs depending on environments.
*7 The operation system must be pre-installed at the factory or clean installed.

484.5 (19-1/16)
425 (16-23/32)59.5
(2-11/32)
9 (11/32) 7 (9/32)
332 (13-1/16)
90
(3-17/32)
165 (6-1/2) 168 (6-5/8)
Dimensions
unit : mm (inch)
N TE: This illustration is not drawn to scale.
SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
4/14
Terminals
12345
8911
10 12 13
67
1 LAN connector
2 HDM input
3 Video input
4 S-Video input
5 RGB 1 input
6 RGB 2 nput
7 DV -D input
8 Audio 1 input
9 Audio 2 input
10 Audio 3 input
11 Audio out put
12 Remote input
13 Serial input

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
5/14
Standard setting-up position
Upper edge of projected image
230
(9-1/16˝)
253.5
(9-31/32˝)
∅60.5
(2-3/8˝)
*
Lower edge of projected image
Projected image
L
L
L
340–420
(13-3/8˝–
16-17/32˝)
431–511
(16-31/32˝–
20-1/8˝)
100 (3-15/16˝)
344
(13-17/32˝)
100
(3-15/16˝)
300
(11-13/16˝)
Projected image
HH
ET-PKD110H
ET-PKD110H
unit : mm (inch)
** Adjustable in 40 mm (1-9/16˝) steps.
Caution:
• All construction work should be done by a qualified technician.
• When mounting to the ceiling, use the special mounting bracket. To prevent the projector from swaying or drop-
ping, attach the wire that is included with the projector between the mounting bracket and the ceiling.
N TE:
Illustrations show the projector installed
using optional ceiling mount bracket.
This illustration is not drawn to scale.
1.02 m
1.27 m
1.52 m
1.78 m
2.03 m
2.29 m
2.54 m
3.05 m
3.81 m
5.08 m
6.35 m
7.62 m
1.29
1.63
1.96
2.30
2.64
2.97
3.31
3.98
4.99
6.67
8.35
10.03
2.64
3.31
3.98
4.65
5.32
5.99
6.66
8.00
10.01
13.36
16.72
20.07
-0.11
-0.14
-0.16
-0.19
-0.22
-0.24
-0.27
-0.32
-0.40
-0.54
-0.67
-0.81
0.27
0.34
0.40
0.47
0.54
0.61
0.67
0.81
1.01
1.35
1.68
2.02
–
–
–
–
–
–
–
–
–
–
–
–
40˝
50˝
60˝
70˝
80˝
90˝
100˝
120˝
150˝
200˝
250˝
300˝
/
/
/
/
/
/
/
/
/
/
/
/
(4.3)
(5.4)
(6.5)
(7.6)
(8.7)
(9.8)
(10.9)
(13.1)
(16.4)
(21.9)
(27.4)
(33.0)
(8.6)
(10.8)
(13.0)
(15.2)
(17.4)
(19.6)
(21.8)
(26.2)
(32.8)
(43.8)
(54.8)
(65.8)
(-0.4
(-0.4
(-0.5
(-0.6
(-0.7
(-0.8
(-0.9
(-1.1
(-1.3
(-1.8
(-2.2
(-2.7
0.9)
1.1)
1.3)
1.5)
1.8)
2.0)
2.2)
2.7)
3.3)
4.4)
5.5)
6.6)
–
–
–
–
–
–
–
–
–
–
–
–
Projection size
[diagonal]
Projection distance [L]
Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens [ H]
Projection distance for 16:10 aspect ratio screen
unit: meters (feet)
N TE:
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
6/14
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 16:10
minimum L (m) = (diagonal screen size in inches) × 0.0336 – 0.0546
maximum L (m) = (diagonal screen size in inches) × 0.0670 – 0.0408
Aspect ratio 16:9
minimum L (m) = (diagonal screen size in inches) × 0.0346 – 0.0546
maximum L (m) = (diagonal screen size in inches) × 0.0689 – 0.0408
N TE: Distances calculated with the above equations will include a slight error.
N TE:
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• At the shortest projection distance, the zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
1.02 m
1.27 m
1.52 m
1.78 m
2.03 m
2.29 m
2.54 m
3.05 m
3.81 m
5.08 m
6.35 m
7.62 m
1.33
1.67
2.02
2.36
2.71
3.06
3.40
4.09
5.13
6.86
8.58
10.31
2.72
3.40
4.09
4.78
5.47
6.16
6.85
8.23
10.29
13.74
17.18
20.63
-0.14
-0.17
-0.21
-0.24
-0.28
-0.31
-0.35
-0.42
-0.52
-0.69
-0.87
-1.04
0.25
0.31
0.37
0.44
0.50
0.56
0.62
0.75
0.93
1.25
1.56
1.87
–
–
–
–
–
–
–
–
–
–
–
–
(4.4)
(5.5)
(6.7)
(7.8)
(8.9)
(10.1)
(11.2)
(13.5)
(16.9)
(22.5)
(28.2)
(33.9)
(8.9)
(11.1)
(13.4)
(15.6)
(17.9)
(20.2)
(22.4)
(26.9)
(33.7)
(45.0)
(56.3)
(67.6)
40˝
50˝
60˝
70˝
80˝
90˝
100˝
120˝
150˝
200˝
250˝
300˝
/
/
/
/
/
/
/
/
/
/
/
/
(-0.5
(-0.6
(-0.7
(-0.8
(-0.9
(-1.0
(-1.1
(-1.4
(-1.7
(-2.3
(-2.8
(-3.4
0.8)
1.0)
1.2)
1.4)
1.6)
1.8)
2.0)
2.5)
3.1)
4.1)
5.1)
6.1)
–
–
–
–
–
–
–
–
–
–
–
–
Projection size
[diagonal] Projection distance [L] Min [wide] Max [telephoto]
Height from the edge of screen
to center of lens [H]
Projection distance for 16:9 aspect ratio screen
unit: meters (feet)

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
7/14
H
(Width of
projected image)
V
(Height of
projected image)
0.65V
0.7V
0.1H0.1H
Standard postition
of projected image
H
(Width of
projected image)
V
(Height of
projected image)
0.65V
0.7V
0.1H0.1H
Standard postition
of projected image
360°
-15°
+15°
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
Installable angle
nstall the projector at an angle within the range shown below.
• Vertical direction
The projector may be installed at a vertical
angle of 360°.
• Horizontal direction
The projector may be installed at a horizontal
angle of ±15°.
• Floor mount • Ceiling mount

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
8/14
List of compatible signals
The signals that can be input to this projector are shown in the table below. Horizontal scanning fre-
quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of
162 MHz maximum can be input.
N TE: The native resolution of this projector is 1,920 × 1,200 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode Display
resolution
(dots)*1
Scanning frequency
H
(kHz) V (kHz)
Dot clock
frequency
(MHz)
Format
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720 × 483
720 × 576
1280 × 720
1280 × 720
1920 × 1080i
1920 × 1080i
1920 × 1080
1920 × 1080i
1920 × 1080
640 × 400
640 × 480
800 × 600
832 × 624
1024 × 768
1152 × 864
1152 × 870
1280 × 720
1280 × 768
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
27.0
27.0
28.1
33.8
67.5
56.3
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
65.5
68.7
80.0
96.7
53.7
64.0
67.5
76.7
68.7
37.1
44.8
39.6
47.8
47.4
60.3
68.6
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
24.0
24.0
50.0
60.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.0
60.0
70.1
75.0
81.6
85.0
100.0
120.0
60.0
71.2
74.9
85.0
75.1
49.8
59.9
49.9
59.9
60.0
74.9
84.8
−
−
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
74.3
74.3
74.3
74.3
148.5
148.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
86.0
94.5
105.0
130.0
81.6
94.2
108.0
121.5
100.0
60.5
74.5
65.3
79.5
68.3
102.3
117.5
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720/60p
720/50p
1080/60i
1080/50i
1080/24p
1080/24sF
1080/25p
1080/30p
1080/60p
1080/50p
VGA400
VGA480
SVGA
MAC16
XGA
MXGA
MAC21
1280 × 720
1280 × 768
1280 × 768*2
1280 × 768
VIDEO/S-VIDEO
SDI/RGB/YPBPR
HDMI/DVI-D/
RGB/YPBPR
HDMI/DVI-D/RGB
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
9/14
Display mode Display
resolution
(dots)*1
Scanning frequency
H
(kHz) V (kHz)
Dot clock
frequency
(MHz)
Format
1280 x 800
1280 x 960
1280 × 1024
1280 × 768
1400 × 1050
1440 × 900
1600 × 1200
1680 × 1050
1920 × 1080
1920 × 1200
41.3
49.7
49.3
62.8
71.6
60.0
52.4
64.0
72.3
78.2
80.0
91.1
47.7
39.6
54.1
64.0
65.2
65.3
78.8
82.2
55.9
46.3
75.0
65.3
54.1
55.6
66.6
67.2
61.8
74.0
74.6
50.0
59.8
59.9
74.9
84.9
60.0
50.0
60.0
66.3
72.0
75.0
85.0
59.8
49.9
50.0
60.0
60.0
60.0
72.0
75.0
59.9
49.9
60.0
60.0
50.0
49.9
59.9
60.0
49.9
60.0
59.9
68.0
83.5
71.0
106.5
122.5
108.0
88.0
108.0
125.0
135.1
135.0
157.5
84.8
69.0
99.9
108.0
122.6
121.8
149.3
155.9
106.5
86.8
162.0
146.3
119.5
141.5
138.5
173.0
158.3
154.0
193.3
1280 × 800
1280 × 800*2
1280 × 800
MSXGA
SXGA
1366×768
SXGA+
WXGA+
UXGA60
WSXGA+
1920×1080
1920×1080*2
1920×1080
WUXGA
WUXGA*2
WUXGA
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D/RGB
RGB
*1 The “i” appearing after the resolution indicates an interlaced signal.
*2Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
10/14
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, com-
mands must be input through communication software, based on the format and satisfying the commu-
nication conditions shown below.
Basic format
Transmission from the computer begins with STX, then the D, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
Communication conditions (factory setting)
Pin assignments and signal names
6
15
9
D-sub 9-pin (female)
Serial input
Description
NC
Send data
Receive data
Connected internally
Ground
Signal name
–
TXD
RXD
–
GND
No.
1
2
3
4
5
Description
NC
Connected internally
Connected internally
NC
Signal name
–
CTS
RTS
–
No.
6
7
8
9
CAUTI N
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 sec-
onds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next
command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10
seconds or more.
• When using two or more units, set different IDs for each unit.
Start
(1 byte)
End
(1 byte)
Colon
(1 byte)
Semicolon
(1 byte)
(2 byte)
ID designator
01 to 06: Address number
ZZ: All units (ID ALL)
ID: 2 characters
(2 bytes) Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
STX ETXC1P1P2...PnC2ADI1I2 C3:;
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9,600 bps
None
8 bits
1 bit
None
None

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
11/14
Cable specifications
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
PC (DTE)Projector
NC
NC
NC
NC
NC
NC
NC
NC
Control commands
Command:Parameter Function Callback
PON
POF
IIS:HD1
IIS:DVI
IIS:RG1
IIS:RG2
IIS:NWP
IIS:VID
IIS:SVD
OPP:0
OPP:1
OSH:0
OSH:1
OFZ:0
OFZ:1
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VPM:DIC
VPM:709
OTE:1
OTE:2
OTE:4
OTE:10
TSD:y1y2y3y4m1m2d1d2w*1
TST:h1h2m1m2s1s2
OOS:0
OOS:1
Standby power on
Standby power off
HDMI
DVI
RGB 1
RGB 2
Network
Video
S-Video
Off
On
Off
On
Off
On
Natural
Standard
Dynamic
Cinema
Graphic
DICOM
Rec. 709
Middle
High
User
Default
Date setting
Time setting
On-screen display off
On-screen display on
POWER (STANDBY)
INPUT SELECT
SIDE BY SIDE
AV MUTE
FREEZE
AUTO SETUP
PICTURE MODE
COLOR TEMPERATURE
DATE
TIME
ON SCREEN
PON
POF
IIS:HD1
IIS:DVI
IIS:RG1
IIS:RG2
IIS:NWP
IIS:VID
IIS:SVD
OPP:0
OPP:1
OSH:0
OSH:1
OFZ:0
OFZ:1
OAS
VPM:NAT
VPM:STD
VPM:DYN
VPM:CIN
VPM:GRA
VPM:DIC
VPM:709
OTE:1
OTE:2
OTE:4
OTE:10
TSD:y1y2y3y4m1m2d1d2w*1
TST:h1h2m1m2s1s2
OOS:0
OOS:1
*1 w: day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
N TE:
• Do not send P N, P F or SH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement
cycle.
• When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.

SPEC FI L E
PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
12/14
Status request commands
Command:Parameter Function DescriptionCallback
QPW
QIN
OPP
QSH
QFZ
QOS
QST
Q$L
QLP
QPM
QTM:0
QTM:1
QTM:2
QGD
QGT
Main power status
Input signal status
Side-by-side function status
AV mute function status
Freeze function status
On-screen display status
Projector run time
Lamp run time
Lamp power mode status
Picture mode status
Temperature status
Date setting status
Time setting status
Standby (Off)
On
HDMI
DVI
RGB 1
RGB 2
Network
Video
S-Video
Off
On
Off
On
Off
On
Off
On
00000h–99999h
0000h–9999h
Normal
Eco
Natural
Standard
dynamic
Cinema
Graphic
DICOM
Rec. 709
p0 = Intake air
p1 = Around lamp
p2 = Optics module
yyyymmddw*2
hhmmss
000
001
HD1
DVI
RG1
RG2
NWP
VID
SVD
0
1
0
1
0
1
0
1
p1p2p3p4p5
p1p2p3p4
0
1
NAT
STD
DYN
CIN
GRA
DIC
709
p1p2p3p4/p5p6p7p8*1
y1y2y3y4m1m2d1d2w
h1h2m1m2s1s2
Command example
To set t e on-screen display off, send t e command as s own below.
ADZZ OOS :0; ETX
ID Address Command
STX
Start Parameter End
NOTE: When send ng commands w thout parameters, a colon (:) s not necessary.
*1 p1p2p3p4: Celsius (°C), p5p6p7p8: Fa ren eit (°F)
*2 w: day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
NOTE: If a wrong command s rece ved, the projector w ll send an ER401 or ER402 command to the computer.

SPEC FI L E PT-DW530
DLP™Projector
As of May 2011
SFD10M013-1
13/14
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1. Never place objects on top of the projector while it is operating.
2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s
exhaust openings.
3. Do not stack projector units directly on top of one another. f two units must be stacked for back-
up use in ordinary projection, use a method as shown below and provide ample space between the
units to ensure that exhaust heat does not accumulate near the intake opening or around the units.
Dual stacked projection is not recommended.
4. Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the pro-
jector so that cool or hot air from other air conditioning equipment does not flow directly toward
the projector’s air intake or exhaust openings.
5. Do not install the projector in an enclosed space. f it is necessary to install it in an enclosed
space, add a separate ventilation system. f ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
6. f the projector is installed in an enclosed space, ensure that the temperature of the air surrounding
the projector is between 0°C (32°F) and 40°C (104°F). Also make sure that the projector’s intake and
exhaust openings are not blocked. Even though the air surrounding the projector is 40°C (104°F) or
less, if hot exhaust air accumulates inside the space, it may cause the projector’s protective circuit
to interrupt projector operation. Pay particular attention to the surrounding temperature conditions
when planning the installation.
7. When installing the projector in any manner other than floor mounting with the adjuster legs, use the
five threaded ceiling mount holes (screw diameter: M4, projector interior thread length: 7 mm) to
secure the projector. Also, provide a 5- to 10-mm (3/16˝ to 13/32˝) space between the projector and
the mounting surface by inserting metal spacers.
500 mm (19-11/16˝ ) or more
500 mm (19-11/16˝ )
or more
500 mm (19-11/16˝ )
or more
Do not stack projector
units directly on top of
one another.
100 mm
(3-15/16˝)
or more

SPEC FI L E
PT-DW530
D P™Projector
As of May 2011
SFD10M013-1
14/14
Operating the projector continuously
1. If the projector is to be operated continuously 22 hours or more, lamp replacement cycle duration
becomes shorter.
2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods (one hour or less).
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
Product availability differs depending on region and country. This product may be subject to export control regulations.
DLP and the DLP logo are trademarks of Texas Instruments.
PJLink is a registered trademark, or a trademark application has been filed, in Japan, the nited States, and other countries and regions.
All other trademarks are the property of their respective trademark owners.
Direction of air intake and exhaust
Intake
Exhaust