Panasonic CZ-CLNC1U User manual

–– Contents ––
1. LonWorks Interface Overview 2
Product Overview
System Diagram
Functions
2. Installation Instructions of LonWorks Interface 4
Safety Precautions
Included Parts
Installation Method
Wiring Specifications
LonWorks Interface Structure
Power Board Initial Settings 5
Power Board Wiring
Wiring Procedure
Main Circuit Board
Indoor Unit Enabling Switches 6
Setting Switches
Address Switches
Communications LED (Green) 7
Data LED (Red)
Diagram of External Dimensions
Product Specifications
3. Assigning Central Control Addresses 8
4. LonWorks Interface Test Run 9
5. Checking the LonWorks Interface Version 10
6. List of LonWorks Network Variables 11
7. Details of LonWorks Network Variables 12
8. Locations Where Neuron ID is Applied 15
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached installation instructions.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
LonWorks is a registered trademark of the Echelon Corporation.
85464369526011
INSTALLATION INSTRUCTIONS
LonWorks Interface
Model No. CZ-CLNC1U
PanaCZ-CLNC1UEng.indd1PanaCZ-CLNC1UEng.indd1 2011/11/1112:23:412011/11/1112:23:41

2
1. LonWorks Interface Overview
Product Overview
This interface is a communications interface for connecting
LonWorks to an air conditioner unit control network.
From the host connected to LonWorks, basic settings and status
monitoring is possible for up to 16 groups of A/C units.
System Diagram


LonWorks
communication line
LonWorks Interface
Inter-unit control wiring
Outdoor
Unit
Outdoor
Unit
Indoor Unit
Indoor Unit
• Up to 16 groups of indoor units (maximum 64 units) can be controlled with 1 LonWorks Interface unit.
For 17 or more groups of indoor units, connect additional interface units.
• Install a remote controller (or system controller, etc.), which can control the A/C units, to an inter-unit control
wiring other than the LonWorks Interface unit.
• Before making the connection to the LonWorks Interface unit, set the central control addresses in the indoor
units.
PanaCZ-CLNC1UEng.indd2PanaCZ-CLNC1UEng.indd2 2011/11/1112:23:412011/11/1112:23:41

3
Functions
A/C unit settings
from the
LonWorks
Settings for
each group of
indoor units
Start/stop
Temp. setting(*1)
Operation mode
Option 1 settings(*2)
Option 2 settings(*2)
Settings for all units Emergency stop
A/C unit status notifications made
to the LonWorks
Start/stop
Temp. setting
Operation mode
Option 1 settings(*2)
Option 2 settings(*2)
Alarm status(*3)
Indoor units with active alarms(*4)
Room temp(*5)
A/C unit status(*6)
Configuration properties
Transmission interval settings(*7)
Minimum time secured
for transmission(*8)
(*1) When a temperature above the upper limit of the temperature which can be set by the indoor units has been specified,
it will be set to the upper limit; conversely, when a temperature below the lower limit has been specified, it will be set to
the lower limit.
(*2) Two options can be selected using the setting switch from among remote-controller prohibit, fan speed setting, air
direction setting and filter sign.
(*3) When indoor units are under group control, an alarm is determined to have occurred when the alarm occurs at one or
more of the units.
(*4) The number of the indoor unit at which the alarm has occurred is notified. This makes it possible to identify at which
indoor unit of the indoor unit group the alarm has occurred.
(*5) When indoor units are under group control, the room temperature of the main unit in the group is notified.
(*6) When an alarm occurs at one or more indoor units, the alarm code is notified as the indoor unit status.
(*7) All the data which can be output is output at the set interval.
(*8) The same data is not output continuously at the set interval.
PanaCZ-CLNC1UEng.indd3PanaCZ-CLNC1UEng.indd3 2011/11/1112:23:412011/11/1112:23:41

4
2. Installation Instructions of LonWorks Interface
Safety Precautions
∗The following is intended for the installer responsible for
installation and test operations of the LonWorks Interface,
and should be carefully read before beginning.
∗The precautions given in this manual consist of specific
“Warnings” and “Cautions.” They provide important
safety-related information and are important for your safety,
the safety of others, and trouble-free operation of the
system. Be sure to strictly observe all safety procedures.
The labels and their meanings are as described below.
Warning
This symbol refers to a hazard or unsafe
procedure or practice which can result
in severe personal injury or death.
Caution
This symbol refers to a hazard or unsafe
procedure or practice which can result
in personal injury or product or property
damage.
※
After installation is completed, perform a test run to check
for operating trouble. As you do, use the central control
device Operating Instructions and explain operating
procedures to the customer. Then request that the customer
store this manual together with the central control device
Operating Instructions.
Warning
• Be sure to arrange installation from the dealer where the
system was purchased or using a professional installer.
Electric shock or fire may result if an inexperienced
person performs any installation or wiring procedures
incorrectly.
• Please install and ensure construction according to Installation
Instructions of LonWorks Interface.
• Only a qualified electrician should attempt to connect this
system, in accordance with the instructions in this manual.
If the electrical circuit capacity is insufficient a danger of
electric shock and fire may be present.
• Use the specified cables (type and wiring diameter) for the
electrical connections, and connect the cables securely.
Run and fasten the cables securely so that external forces
or pressure placed on the cables will not be transmitted to
the connection terminals. Overheating or fire may result if
connections or attachments are not secure.
Caution
Depending on the installation conditions and location, an earth
leakage breaker may be required. If an earth-leakage breaker
is not installed, there is a danger of electric shock or fire.
Included Parts
No. Part Qty
(1)
Installation Instructions
1
Installation Method
• The screws used to install the main unit must be provided by
the installer.

• Install the LonWorks Interface away from any sources of
electrical noise.
Wiring Specifications
• For the inter-unit control wiring use twin-core AWG#20 –
AWG#14 cables.
• For the LonWorks communication line cables, use twisted-
pair cables with a wire diameter of 0.51 mm(AWG#24) or
larger as recommended by Echelon Corp.
Examples of cables recommended by Echelon Corp.
Cable type Wire diameter
/AWG
Total cable length
Bus type Free
24 AMG twisted-pair
(TIA568A category 5)
0.51 mm
/24
900 m
(2953 ft.)
450 m
(1476 ft.)
• Do not use the same cable for the inter-unit control wiring, the
LonWorks communication lines, and the power cable. Do not
run them through the same conduit or place the cables near
one another.
• Connect the cables so that there is no miswiring.
(Miswiring can cause malfunction.)
LonWorks Interface Structure
• This interface contains 4 LonWorks communication boards (nodes).
• Up to 4 indoor unit groups (maximum 32 units) can be
assigned to 1 node.
Main circuit
board Node 3
Main circuit
board Node 2
Main circuit
board Node 1
Main circuit
board Node 0
Power
board Power transformer
PanaCZ-CLNC1UEng.indd4PanaCZ-CLNC1UEng.indd4 2011/11/1112:23:412011/11/1112:23:41

5
Power Board Initial Settings
Not Install: Ordinarily, keep this set to “Not Install” (initial setting).
Install: Free topology terminal resistor (51Ω) for the
LonWorks communication lines.
ON
OFF
S002
S001
CN005
100-120/200-240 V
50/60 Hz 1-PH
Power transformer primary-side
Not Install
Power board
(when AC 100-120V
power is connected)
Power switch
CN006 (when AC 200-
240V power is connected)
Install
When AC 200-240V power is connected, connect the power
transformer primary-side to CN006. When AC 100-120V power is
connected, connect the power transformer primary-side to CN005.
(It is connected to CN006 when the unit is shipped from the plant.)
Power Board Wiring
Power board
6
CN003
1
3
CN002
1
L
N
100-120/200-240 V
50/60 Hz 1-PH
LON communication
lines (2)
LON communication
line (2) (reserve)
LON communication
lines (1)
LON communication
line (1) (reserve)
Earth for power wiring
Inter-unit
control lines
Inter-unit
control line (reserve)
• The LonWorks communication lines can be connected
to either (1) or (2) in the above figure. The results are the
same.
• Do not run the inter-unit control lines, the LonWorks
communication lines, and the power cables through the
same conduit, or place the cables near one another. Doing
so can cause the system to malfunction.
• Before turning the power on, follow the instruction in Power
Board Initial Settings.
• When using the spare inter-unit cotrol line, connect [1] and [3]
at CN002.
• When using the spare LON communication line, connect [1]
and [3] or [4] and [6] at CN003.
Wiring Procedure
• Connect the power supply lines to the L and N power supply
terminals.
(the power suplly neutral to the N terminal.)
• Connect an earth ground line to the screw.
L N
Lon communication wiring
Conduit (Power cables)
Power board
Inter-unit control wiring
Main Circuit Board
IC002
Data
S002
S001
S003
LD009
LD001~LD008
COM
Neuron ID label
S004
Indoor unit enabling SW
S005
Address SW S006
Setting SW
PanaCZ-CLNC1UEng.indd5PanaCZ-CLNC1UEng.indd5 2011/11/1112:23:422011/11/1112:23:42

6
Indoor Unit Enabling Switches
OFF
1 2 3 4 OFF Indoor unit group 3 is disabled.
ON Indoor unit group 3 is enabled.
OFF Indoor unit group 2 is disabled.
ON Indoor unit group 2 is enabled.
OFF Indoor unit group 1 is disabled.
ON Indoor unit group 1 is enabled.
OFF Indoor unit group 0 is disabled.
ON Indoor unit group 0 is enabled.
• One main circuit board can control 4 groups (indoor unit
groups 0 – 3).
• Set to “disable” if the indoor unit group does not exist. Set to
“enable” if the indoor unit group exists.
Setting Switches
Address Switches
OFF
1 2 3 4 5 6 7
6
-
-
-
-
O
O
O
O
7
-
-
O
O
-
-
O
O
8
-
O
-
-
O
-
O
O: ON -: OFF R/C: Remote Controller
Option 1 Option 2
R/C prohibit Fan speed
R/C prohibit Air direction
R/C prohibit Filter sign
Fan speed Air direction
Fan speed Filter sign
Air direction Filter sign
--- ---
--- ---
OFF Central/individual setting is according to the
central control device (normal setting).
ON Central/individual setting is always set to “individual.”
OFF Control temperature is used for the room
temperature (normal setting).
ON Inlet temperature is used for the room temperature.
Not used (Be sure to set to OFF.)
Not used (Be sure to set to OFF.)
OFF Communicate as a “sub” central control device.
ON Communicate as a “main” central control device.
• If there are no central control devices other than this
interface, set to “main” (ON).
• To set this interface as the main, set only node 0 to
“main” (ON).
• If using in combination with an communication adapter,
AMY adapter, intelligent controller, or system controller,
set to “sub” (OFF).
• If using in combination with an ON/OFF controller, set the
ON/OFF controller as the main if the ON/OFF controller’s
remote-controller prohibit function is to be used. If this
interface’s remote-controller prohibit function is to be
used, set this interface as the main.
1 2 3 4 5 6
OFF O : ON - : OFF
Address switch Central control
address
123456
-
O
-
O
-
-
O
O
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1
2
3
4
-
O
-
O
-
-
O
O
O
O
O
O
-
-
-
-
-
-
-
-
-
-
-
-
5
6
7
8
-
O
-
O
-
-
O
O
-
-
-
-
O
O
O
O
-
-
-
-
-
-
-
-
9
10
11
12
-
O
-
O
-
-
O
O
O
O
O
O
O
O
O
O
-
-
-
-
-
-
-
-
13
14
15
16
-
O
-
O
-
-
O
O
-
-
-
-
-
-
-
-
O
O
O
O
-
-
-
-
17
18
19
20
-
O
-
O
-
-
O
O
O
O
O
O
-
-
-
-
O
O
O
O
-
-
-
-
21
22
23
24
-
O
-
O
-
-
O
O
-
-
-
-
O
O
O
O
O
O
O
O
-
-
-
-
25
26
27
28
-
O
-
O
-
-
O
O
O
O
O
O
O
O
O
O
O
O
O
O
-
-
-
-
29
30
31
32
-
O
-
O
-
-
O
O
-
-
-
-
-
-
-
-
-
-
-
-
O
O
O
O
33
34
35
36
-
O
-
O
-
-
O
O
O
O
O
O
-
-
-
-
-
-
-
-
O
O
O
O
37
38
39
40
-
O
-
O
-
-
O
O
-
-
-
-
O
O
O
O
-
-
-
-
O
O
O
O
41
42
43
44
-
O
-
O
-
-
O
O
O
O
O
O
O
O
O
O
-
-
-
-
O
O
O
O
45
46
47
48
-
O
-
O
-
-
O
O
-
-
-
-
-
-
-
-
O
O
O
O
O
O
O
O
49
50
51
52
-
O
-
O
-
-
O
O
O
O
O
O
-
-
-
-
O
O
O
O
O
O
O
O
53
54
55
56
-
O
-
O
-
-
O
O
-
-
-
-
O
O
O
O
O
O
O
O
O
O
O
O
57
58
59
60
-
O
-
O
-
-
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
61
62
63
64
PanaCZ-CLNC1UEng.indd6PanaCZ-CLNC1UEng.indd6 2011/11/1112:23:422011/11/1112:23:42

7
Communications LED (Green)
LD001 LD002 Display meaning
X
X
X
X
X
Low
High
O
①Power OFF
②
-----
③Flash writer writing in progress
④
Waiting for A/C unit initial communication
Low
Low
Low
Low
X
Low
High
O
⑤
A/C unit initial communication in progress
⑥
-----
⑦
LonWorks communication microcomputer error
⑧EEPROM error
High
High
High
High
X
Low
High
O
⑨
-----
⑩
-----
⑪
-----
⑫
-----
O
O
O
O
X
Low
High
O
⑬Test run mode
⑭
-----
⑮Version display in progress
⑯Normal communications in progress
X: Not lit,Low: Low-speed flashing (once/second)
High: High-speed flashing, O: Constantly lit
Data LED (Red)
Communications
LED
Data LED display meaning
①
②
③
④
No LED lit
All LEDs lit
------
Displays the wait time (seconds) for A/C
unit initial communication.
⑤
⑥
⑦
⑧
Displays the A/C unit communications status
------
No LED lit
No LED lit
⑨
⑩
⑪
⑫
------
------
------
------
⑬
⑭
⑮
⑯
According to the test run mode specifications
------
According to the version display specifications
Displays the A/C unit communications status
COM
12
LD
COM: Communications
Data
3 4 5 6 7 8
LD
• Display of A/C unit communications status
LD Display meaning
Indoor unit
group
OFF: Waiting for initial communication
Low-speed flashing: Waiting for minimum
transmission interval
High-speed flashing: Initial communication
in progress
ON: Normal communications in progress
003 0
004 1
005 2
006 3
007 Illuminates for 200 ms when data is output to the
LonWorks communicator.
008 Illuminates for 200 ms when data is output to the
indoor/outdoor communicator.
Diagram of External Dimensions
Unit : in.
8-15/32
1-15/16
4-21/64
4-17/32
7-7/8
3-7/64
3-ø7/8
4-ø13/64
18-1/64
19-11/16
1-1/32
1-11/32 1-31/32
1-1/32
4-R3/32
6-1/2 7-7/16
4-R13/64
1-11/32 1-31/32
6-1/2
7-7/16
9-29/649-29/64
9-19/64
9-39/64
Product Specifications
Connects to LonWorks network
FTT-10 A transceiver device
Power 100-120/200-240 V 50/60 Hz 1-PH
Power
consumption
11 W max.
Service
environment
conditions
Temp. 32 to 104°F, humidity 20 to 80%
Indoor use only
External
dimensions
3-7/64 in.(H) × 19-11/16 in.(W) × 8-15/32 in.(D)
Weight Approx. 7.27 lb.
PanaCZ-CLNC1UEng.indd7PanaCZ-CLNC1UEng.indd7 2011/11/1112:23:422011/11/1112:23:42

8
3. Assigning Central Control Addresses
• Before assigning central control addresses for the LonWorks
Interface, use the remote controller to make central control
address settings for A/C units.
• Follow only the steps for “Assigning Central Control Addresses”
when a system controller or other central controller is already
provided.
[Setting Central Control Addresses]
(1) Press and hold both the and buttons for 4
seconds or longer.
Check that the “SETTING” display on the remote controller
is flashing.
(2) Set the “03” item code by pressing the and
temperature setting buttons.
(3) Set the desired central control address by pressing the
and timer buttons.
(4) Press the button, and check that the “SETTING”
display stops flashing and illuminates instead.
(The setting data cannot be changed unless the
button is pressed.)
(5) Press the button, and check that the display on the
remote controller has been cleared.

(2)
(4)
(5)
(3)
(1)
For example, in this case
Indoor unit address: 1-8
Central address: 17
remote controller
[Assigning Central Control Addresses]
(1) Turn the power switch (S001) on the LonWorks Interface
power board to OFF.
(2) Turn the setting switch (S006-2) to OFF (so that central
control addresses are set with the DIP switches).
(3) Set the first central control address with the address
switch (S005). When assigning serial numbers, a
consecutive series of numbers is assigned for the central
control addresses.
<Example> If the first central control address is “5,” then
this circuit board assigns central control
addresses “5,” “6,” “7,” and “8.”
(4) Make the enable/disable settings with the indoor unit
enabling switches (S004).
<Example> If central control addresses “6” and “8” do not
exist, enable only “5” and “7.”
(5) Turn the power switch (S001) on the LonWorks Interface
power board to ON.
OFF
1 2 3 4 5 6 7
S006
OFF
1 2 3 4 5 6
S005
OFF
1 2 3 4
S004
“5” is set as the central control
address for indoor unit group 0,
and “7” is set as the central
control address for indoor unit
group 2.
PanaCZ-CLNC1UEng.indd8PanaCZ-CLNC1UEng.indd8 2011/11/1112:23:422011/11/1112:23:42

9
4. LonWorks Interface Test Run
Before performing a test run of the LonWorks Interface,
perform test runs of the A/C units and assign central control
addresses for A/C units.
[LonWorks Interface Test Run Procedure]
(1) Press and hold touch-switch S001 on the main circuit board
for 5 seconds or longer.
Test run mode is enabled for the main circuit board that is
currently being controlled. LD001 illuminates, and LD002 –
LD008 turn off.
(2) Press touch-switch S002. The data LEDs appear as shown
in the tables below.
In addition, the assigned indoor unit groups start and stop
as shown in the tables below.
(3) Be sure to reset the power after the LonWorks Interface test
run is completed.
1
2
Data
345678
LD
COM
1
2
Data
345678
Indoor unit Gr
0
1
2
3
Start/stop
Stop
Stop
Stop
Stop
STEP 1
S002 PUSH
1
2
Data
345678
Indoor unit Gr
0
1
2
3
Start/stop
Start
Stop
Stop
Stop
STEP 2
1
2
Data
345678
Indoor unit Gr
0
1
2
3
Start/stop
Start
Start
Stop
Stop
STEP 3
1
2
Data
345678
Indoor unit Gr
0
1
2
3
Start/stop
Start
Start
Start
Stop
STEP 4
S002 PUSH
S002 PUSH
S002 PUSH
COM
COM
COM
COM
S002 PUSH
S002 PUSH
1
2
Data
345678
Indoor unit Gr
0
1
2
3
Start/stop
Start
Start
Start
Start
STEP 5
1
2
Data
345678
Indoor unit Gr
0
1
2
3
Start/stop
STEP 1
COM
COM
Stop
Stop
Stop
Stop
PanaCZ-CLNC1UEng.indd9PanaCZ-CLNC1UEng.indd9 2011/11/1112:23:432011/11/1112:23:43

10
5. Checking the LonWorks Interface Version
(1) Press touch-switch S002.
Version display mode is enabled on that circuit board for
a period of 18 seconds. LD001 illuminates, and LD002
flashes at high speed.
(2) While the version is displayed (18 seconds), the display
contents are the following.
• Version display
03 4 5654 6
53
1456363 6
45
23 5 6476
53 4
35 6
34 83456
43 4 6594 5
3 6
<Example> Main microcomputer Version 3.56
LonWorks I/F microcomputer Version 2.00
1
2
COM
First 3 seconds
Next 3 seconds
Next 3 seconds
Next 3 seconds
Next 3 seconds
Last 3 seconds
Data
345678
Data
34 5 6 87
Data
3456 87
Data
345678
Data
34 5 6 87
Data
34 5 6 87
Data
5678
Data
4687
Data
3687
34
35
45
Data
567834
Data
468735
5
“3”
“0”
“2”
“6”
“0”
Data
36874
“5”
Off
High-speed flashing
Displays the first
digit of the main
microcomputer
version
Displays the second
digit of the main
microcomputer
version
Displays the third
digit of the main
microcomputer
version
Displays the first
digit of the LonWorks
I/F microcomputer
version
Displays the second
digit of the LonWorks
I/F microcomputer
version
Displays the third
digit of the LonWorks
I/F microcomputer
version
Lit
Lit
Lit Lit
Lit
Lit
Lit Lit
Lit
Off
Off
Off
PanaCZ-CLNC1UEng.indd10PanaCZ-CLNC1UEng.indd10 2011/11/1112:23:432011/11/1112:23:43