Panasonic SB-PM4EG User manual

Type 1 way, 1 speaker system
Speaker (s)
Full range 10 cm cone type (4 Ω)
Impedance 4Ω
Input power (IEC) 10 W (Max)
Output sound pressure 83 dB/W (1.0 m)
Frequency range 61 Hz to 17 kHz (-16 dB)
95 Hz to 15 kHz (-10 dB)
1 System Combination 2
1.1. System Breakdown 2
2 Connection of the Speaker Cables 3
3 Exploded view 4
©2007 Matsushita Electric Industrial Co. Ltd.. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
SB-PM4EG
Colour
(M)... Wood Type
Dimensions (W x H x D) 139 x 227 x 136 mm
Mass 1.3 kg
Notes :
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
3.1. Cabinet Parts Location 4
3.2. Packaging 5
4 Replacement Parts List 6
Speaker System
Specification
CONTENTS
Page Page
ORDER NO. MD0703002CE

1 System Combination
1.1. System Breakdown
Note : The table below show the breakdown for speaker combinations used in main unit systems.
System SC-PM4DBEB/E/EG/EB-S
Music center SA-PM4DBEB/E/EG/EB-S
Front speakers SB-PM4EG-M
2
SB-PM4EG

· Be sure to connect speaker cables before connecting the
AC power supply cord.
· The load impedance of any speaker used with this unit must
be 4 Ω.
· Be sure to connect the cable from the right speaker to the
right terminal and the cable from the left speaker to the left
terminal.
1. Twist and pull off the vinyl tip of the speaker cords. If the
speaker cords do not have vinyl tips, connect them directly
to the terminals. Make sure the bare ends of the wires are
not unravelled.
2. Insert the wire to the rear panel of the unit and close the
lever.
Notes :
· To prevent damage to circuitry, never short-circuit positive
(+) and negative (-) speaker wires.
· Be sure to connect only positive (red) wires to positive (+)
terminals and negative (black) wires to negative (-)
terminals.
Placement
Speakers are designed identically so that no left or right
channel orientation is necessary.
Connection
Use only the supplied speakers
The combination of the main unit and speakers provide the
best sound. Using other speakers can damage the unit and
sound quality will be negatively affected.
Note
· Keep your speakers at least 10 mm away from the system
for proper ventilation.
· These speakers do not have magnetic shielding. Do not
place them near televisions, personal computers or other
devices easily influenced by magnetism.
· You cannot take the front net off the speakers.
2 Connection of the Speaker Cables
3
SB-PM4EG

3 Exploded view
3.1. Cabinet Parts Location
SB-PM4EG
4

3.2. Packaging
SB-PM4EG
5

4 Replacement Parts List
Notes :
· Important safety notice :
When replacing any of these components, be sure to use
only manufacturer’s specified parts shown in the parts list.
· [M] markings in the Remarks columns indicates parts
supplied by PAVCSG.
Ref.
No.
Part No. Part Name & Description Remarks
CABINET AND CHASSIS
1RFKABPM4EG-M SPEAKER UNIT [M]
1-1 RKA0072-KJ LEG CUSHION [M]
PACKING MATERIALS
P1 RPNV0094-J POLYFOAM [M]
P2 RPFV0056 MIRAMAT [M]
6
SB-PM4EG
FLE0703