Panasonic KX-T30810-1 User manual

SPECIFICATIONS
NAME AND LOCATION
CONNECTION
PROGRAMMING

SPECIFICATIONS
General Description
1. Capacity ..................................... Outsides (CO) 3
Stations 8
2. Control Method ............................Stored Program CPU: 8 bits CPU, 4 bits CPU
Control ROM: 48 KB, Control RAM: 8 KB
3. Switching .................................... Space Division CMOS Crosspoint Switch
4. Power Supplies ...........................Primary AC 120 V 60 Hz
Secondary Station Supply Volt: +26 V,
Circuit Volt: +5 V, +12 V, +18 V, +26 V
Power Failure *3 outsides assigned to stations (1 through 3)
...power failure transfer
*System operation for 4 hours by optional Backup Adaptor.
5. Dialing....................................................Outward Dial Pulse 1OPPS
Tone Dial
Internal Dial Pulse lOPPS, 2OPPS
Tone Dial
Mode Conversion DP-DTMF, DTMF-DP
6. Connector .................................. Outsides (CO) Modular Jack (RJ-11)
Station Modular Jack
Paging Output Pin Jack (PCA JACK)
External Music Input two-conductors Jack (MINI JACK 9/64 inch
diameter)
7. EXT Connection ...........................Cable 1 pair wire (Standard Telephone)
2 pair wire (KX-T30830/KX-T30820)
8. Intercom Paths ........................... 3
9. Dimensions ................................334 (W) x437 (H)x 107 (D) mm
(136/32" x 177/32" x 47/32")
10. Weight ........................................ 5 kg (11 lb 0.4 oz)
11. Power Consumption....................40 W (Max.)
Characteristics
1. Station Loop Limit ....................... KX-T30830/KX-T30820 40 ohms
Standard Telephone 600 ohms including set
Doorphone 20 ohms
2. Minimum Leak Resistance ........... 15,000 ohms
3. Maximum Number of Station
Instruments per Line...................... 1 (KX-T30830 or KX-T30820) or 3 (Standard telephone)
4. Ring Voltage ................................. 90 Vrms at 20 Hz depends on Ringing Load
5. Primary Power .............................. 120 Vac, 60 Hz, 0.4 A maximum
6. Central Office Loop Limit ..............1600 ohms maximum
7. Environmental Requirements ......0-40°C, 10%-90%
8. Hookswitch Flash Timing Range . . 204-1000 msec
Design and specifications are subject to change without notice.
1. There are 2 types of model KX-T30810,
such as KX-T30810 and KX-T30810-1.
2. The model KX-T30810-1, have a
mark® on the name plate in figure left.
3. Please use this manual for model KX-
T30810-1.
(Model KX-T30810) (Model KX-T30810-1)
Panasonic EASA-PHONE osTro
MODEL NO. KX-T30810
TELEPHONE EQUIPMENT UI
POWER SINCE Ar\.,1204 GM 40W
0.40 SERIAL NO.
Complies With Part 68. FCC Rules
FCC Registration Number AC,196N- 71853 -MF-
E Rin
g
er E
q
uivalence 0.48
Matsushita Electric Industrial Co Ltd Made in Japan
Part No. T241ZA
,43E
Panasonic EASA-PHONE p oSTE0
MODEL NO. KX-T30810 TELEPHONE
EQUIPMENT
POWER MICE AC"\,12114 0011140W 0.40 p436.
SERIAL NO
Complies With Part 68, FCC Rules
FCC Registration Number ACJ96N- 71853 -MF-E
Rin
g
er E
q
uivalence 0 46
Matsushita Electric Industrial Co Ltd Made In Japan
Part No 7373ZA

NAME AND LOCATION
Fig. 3
Push Buttons A and B simultaneously to open Front Cover.
Button A
Button B
N
ight Indicator
D
ay Indicato
r
P
ower Indicato
r
Ground Terminal
B
attery Backup Connecto
r
S
tat
i
on
M
o
d
u
l
ar
J
ac
k
s
R
eset Button
System Program Switch
P
aging Jack External
M
usic Jac
k
P
ower
S
w
i
tc
h
Fig.
4
0
0
0 0 0
0
Outside Modular
J
acks (CO)

(One pair)
PROGRAMMING
Programming Instructions
I. At extension 11:
All system programming changes (example: system
clear, station program clear, toll restriction,
hookswitch flash timing...) are done through
extension 11.
• Extension 11 must always be a Panasonic
model, KX-T30830.
2. System Program Switch setting:
The System Program Switch located on the KX-
T30810 must be set to the PROGRAM position
while making program changes. After all
programming changes are completed, return the
program switch to the SET position.
3. Overlay:
This overlay is used for programming the system
and the program function names on buttons are
inscribed on this card. Refer to page 7.
4. Before system programming, you may operate
system clear and station program clear to set
default data of programming.
A. System Clear:
I Dial (99).
• "SYSTEM CLEAR-will be displayed.
2 Press the NEXT button.
• "ALL CLEAR?" will be displayed.
3 Press the MEMORY button to clear system.
4 To exit from system clear, press the END
button.
The following features are preset as the default
data.
Date and Time
System Speed Calling
CO Connection Assignment
Dial Mode (Tone/ Pulse) Selection
Switching Mode ( Dayl Night Service)
Starting Time (Day/Night Service)
Flexible Day Outward Dialing Assignment
Flexible Night Outward Dialing Assignment
Flexible Day Ringing Assignment
Flexible Night Ringing Assignment
Toll Restriction—Class Assignment
Toll Restriction—Area Code Selection
Programmable Operator Call
Host PBX Access Codes Assignment
Automatic Answering (Automatic/Manual)
Selection
P
referred Line Assignment
P
rogrammable Call Waitin
g
D
uration Time Count Start Mode
H
ookswitch Flash Timin
g
D
isconnect Time
Calling Party Control (CPC) Signal
I
ntercom Alerting Mode
P
rogrammable Doorphone
D
ial Call Pickup Group Assignment
B
usy Tone Selection
H
old Time Reminder
H
old Recall Time Set
P
rogrammable External Paging Access Tone
D
TMF Receiver
P
rogrammable Toll Prefix
P
rogrammable Secret Auto Dial
B
. Station Program Clear: I
D
ial (98).
• "EXT CLEAR" will be displayed.
2 Press the NEXT button.
• "ALL CLEAR?" will be displayed.
3 Press the MEMORY button to clear the
system.
4 To exit from station clear, press the END
button.
The following features are preset as the
default data.
One Touch Dialing
Background Music
Call Forwarding
Data Line Security
Dial Call Pickup Deny
Do not Disturb

When the System Program Switch on the KX-T30810 is set to the PROGRAM position, the operation of the KX-T30830
will change as follows.
Fig. 6
CLEAR button
P
ROGRAMMABLE
F
EATURE button
L
IQUID CRYSTAL
(LC) Display
PAUSE button
1—> button <-
7 button
SELECT button
I
NTERCOM (1CM) button
N
EXT button
,
I
—
button
PREVIOUS button
FLASH button
E
ND button
KX
-T3083
0
D
IRECT STATION
SELECTION (DSS) button
A
UTO/MEMORY button
CENTRAL OFFICE (CO)
L
INE button
Notes: 1. For details of installation, refer to the Installation Manual (Part No. PQQX5289Z).
2. For details of operation, refer to the User Guide (Part No. PQQX5291Z).

POWER
ON
OFF
Example of Programming
I
. Turn t
h
e Power
S
witc
h
to
O
N ........................................................
2. Set the System Program Switch to PROGRAM .............................
The LCD on the KX-T30830 shows ENTER PGM
CODE".
• Be sure the handset of the extension 11 is in the cradle and the
speakerphone button of the extension 11 is off.
3. To program automatic line access number 9 and the phone
number 987-654-3210 into memory location (speed dial access)
number 00.
KX-T30830 at extension 11
(Extension 11 must always be KX-T30830.)
1. Dial (01) or press the
AUTO button. Display
SPEED CALLING
2. Press the NEXT button. ENTER SPEED CODE
3. Dial (00) or press the
NEXT button.
• If nothing is stored in
access code "00",
00: NOT STORED
• If already stored the
automatic line access
number 9 and the
phone number 123-
456-7890,
00: -123-456-7890
i
4. ® Dial "9".
C Press "—" button.
® Dial "987".
® Press "—" button.
C) Dial "654".
© Press "—" button.
® Dial "3210".
00: -987-654-3210
5. Press the MEMORY
button. 00: -987-654-3210
6.
• To program a next access code, press the NEXT
button.
• To program a desired access code, press the
SELECT button and then dial the number.
7. Repeat step 4 to 6.
8. To return to the initial
program mode, press the
END button.
ENTER PGM CODE
4. Return the System Program Switch to SE
T
• To make program change, start from the beginning.
SYSTEM
SET
PRO
-
GRAM
0
63E3E3
061
r,
36
.
363
0
61QU Il
O
_
C
0
o
d
o
0/
• You will hear the beeps after press
the MEMORY button. •
• The MEMORY indicator light goes on when the
M
EMORY button is pressed, and then Indicato
r
light goes out when the NEXT or PREV button is
pressed.
While programming if a mistake is made,
1. Press t
h
e "END"
b
utton.
3. Start programming procedure from
the beginning.

•PROGRAMMING TABLE
TO SET
P
ROGRAM
A
DDRES
S
STEPS REQUIRED TO CHANGE PROGRAM
Date and Time [00] [NEXT] [A] [EN [SELECT] [EN [B] [EN [SELECT] [EN [C] [EN [D] [EN [SELECT] [MEMORY] [END]
L
.
d
ay o
f
th
e
L. year L-• -month L.- day :-. hour :--- minute L -- — .AM/PM
week
System Speed Calling
Entry [01]
or
[AUTO]
[NEXT] [AB] [CD] [phone number] [MEMORY]
.' r[9]: automatic line access number
L [81] through [83]: outside line access number --
- speed access code
• To advance to the next code.
[SELECT] [AB] [CD] [phone number] [MEMORY]
• To exit the speed calling entry, press [END].
CO Connection
Assignment [02] [NEXT] [NEXT] [SELECT] [MEMORY] [END]
I
;--- - — CONNECT/NO CONNECT
1_------ - until the desired CO number appears
Default To make program change
CO(s) all CO's 12 3
Connect x
No connect
Dial Mode (Tonel Pulse)
Selection [03] [NEXT] [NEXT] [SELECT] MEMORY] [END]
TONE/PULSE
desired CO number appears
-----
- -- until t
h
Default To make program change
C 0 (s) all COs 1 2 3
Tone (DTME) mode x
Pulse mode
Switching Mode
(DaylNight Service) [04] [NEXT]
[SELECT][MEMORY] [END]
L- ---- MAN/AUT
O
Default To make program change
Manual x
A woman(
Starting Time
(DaylNight Service) [05] [NEXT] [A] KN [B] [EN [SELECT] [MEMORY] [NEXT] [C] [EN [D] [co] [SELECT] [MEMORY] [END]
(hour)
!---minute ---.- AMI PM :•-minute L -----
A
M
/
1--• starting time for day service (hour) ._ starting time for night ser
v
Default To make program change
Da
y
p
lan 9:00 AM
Night plan 5:00 PM
Flexible Day Outward
Dialing Assignment [06] [NEXT] [NEXT][C...E][MEMORY] [END]
CO number
the desired extension number appears
"----- ----
-
------------------------ unti
l
Default To make program change
Extensions all extensions 11 12 13 14 15 16 17 18
CO 1 x
CO2 x
CO3 x
[NEXT] [NEXT] [C...E] [MEMORY] [END]
Flexible Night Outward
Dialing Assignment [07] -- CO number
1--- ---- until the desired extension number appears
Default To make program change
Extensions all extensions 11 12
13 14 15 16 17 18
CO 1 x
CO2 x
CO 3 x

TO SET PRO
ADDRESSGRAM STEPS REQUIRED TO CHANGE PROGRAM
Flexible Day Ringing
Assignment [08] [NEXT] [NEXT] [C...E] [MEMORY] [END]
T-. CO number
.---- until the desired extension number appears
Default To make program change
Extensions all extensions I1 12 13 14 15 16
17 18
COI x
CO2 x
CO 3 x
Flexible Night Ringing
Assignment [09] [NEXT] [NEXT][C...E][MEMORY] [END]
CO number
extension number appears
L_____.
L__ until the desire
d
Default To make program change
Extensions an ettellsiunS
II 12 13 14 15 /6 17 18
CO1 x
CO2 x
CO3 x
Toll Restriction—Class
Assignment [10] [NEXT] [NEXT][SELECT][MEMORY] [END]
1121314
desired extension number appears
I
-
----CLASS
L_ --------until th
e
Default To make program change
Extensions all extensions I / /2 13 14
15 16 17 /8
Class I tall calls) x
Class 2 (toll calls,
local calls)
Class 3 (selected
area-codes, local
calls)
Class 4 (local calls)
Toll Restriction—
Area Code Selection [11] [NEXT]
[
NEXT
]
[
C
]
[
MEMOR
Y]
[END]
code with 3 digits
the desired memory location number appears
' '-• - a
r
L-- — until
Memory location number
00 01 02 03 04 05 06 07 08 09
Area code entry
Programmable Operator
Call [12] [NEXT][NEXT] [SELECT] [MEMORY] [END]
-- -- • ENABLE/DISABLE
-- serail the desired extension number appears
Default To make program change
Extensions an extensions 11 12 13 14 15 /6 17 18
Enable x
Disable
Host PBX Access Codes
Assignment [13] [NEXT] [NEXT][A...D][MEMORY] [END]
up to four outside access codes each with a maximum of 2 digit
s
the desired CO numbers appears
L - - - - .
-- --------------unti
l
CO Outside access codes of the host PBX
3
Automatic Answering
(Automatic' Manual)
Selection
[14] [NEXT][NEXT][SELECT][MEMORY
]
[END
A
UTO ANSWERIMAN ANSWER the
desired extension number appears
L-----
----------------------- -- unti
l
Default To make program change
Extensions all extensions 11 12 13 14 15 16 17 18
Automatic x
Manual

TO SET PROGRAM
ADDRESS STEPS REQUIRED TO CHANGE PROGRAM
Preferred Line
Assignment [15] [NEXT] [NEXT] [SELECT] [MEMORY] [END]
I ------ • • • •
(
none
//CO
I
/CO2/CO3
1
'--- until the desired extension number appears
Default To make program change
Extensions all extensions 11 12 13 14 15 16 17 18
• • • • (none) x
C01
CO2
CO3
Programmable Call
Wailing [16] [NEXT
]
[NEXT] [SELECT] [MEMORY] [END]
ENABLE/DISABLE
extension number appears
---- until the desire
d
Default To make program change
Extensions all extensions 11 12 13 14 15 16 17 18
Disable x
Enable
Duration Time Count
Start Mode [17] [NEXT] [SELECT] [MEMORY] [END]
AFTER DIALIIOS AFTER DIAL
L---INSTANTLYI5
S
Default To make program change
Instantly
5S after dial x
lOS after dial
Hookswitch Flash Timing [18] [NEXT [NEXT][SELECT][MEMORY] [END]
MS/600 MS/900 MS CO
number appears
----30
0
L- --- until the desire
d
Default To make program change
CO(s) all CO's 1 2 3
300 cosec
600 cosec x
900 msec
Disconnect Time [19] [NEXT] [NEXT][SELECT][MEMORY] [E ND ]
SEC/4.0 SEC
CO number appears
L- -- 1.
5
'-- until the desire
d
Default To make program change
CO(s) all CO's 1 2 3
1.5 sec x
4.0 sec
Calling Party Control
(CPC) Signal [20] [NEXT][NEXT] [SELECT] [MEMORY] [END]
ENABLE/DISABLE
CO number appears
-- until the desire
d
Default To make program change
CO(s) all CO's
1 23
Enable
x
Disable
Intercom Alerting Mode [21] [NEXT] [NEXT][SELECT][MEMORY] [END]
CALL/VOICE CALL
extension number appears
L---TON
E
L-- until the desire
d
Default To make program change
Extensions all extensions 11 12 13 14 15 16 17 18
Tone call x
Voice call
Programmable
Doorphone [22] [NEXT] [NEXT] [SELECT] MEMORY] [END
1, 2/1/2/ • • • (deny the ringing)
extension number appears
L-- D-PHONE L-
- until the desired
Default To make program change
Extensions all extensions I1 12 13 14 15 16 17 18
Doorphone
I
x
Doorphone 2 -
x
deny the ringing

TO SET PROGRAM
ADDRESS STEPS REQUIRED TO CHANGE PROGRAM
Dial Call Pickup Group
Assignment [23]
[NEXT] [NEXT] [SELECT] [MEMORY] [END]
L -------- PICKUP-G:1/2/1, 21 • • • (out of the group)
---- until the desired extension number appears
Default To make program change
Extensions-all extensions 11 12 13 14 15 16 17
18
Pickup Group 1 x
Pickup Group 2
out of the group
Busy Tone Selection [24] [NEXT] [SELECT][MEMORY] [END]
1/2
------------ TONE
Default To make program change
Tone 1 x
Tone 2
Hold Time Reminder [25] [NEXT] [SELECT] [MEMORY] [END]
I MIN/2 MIN ................../9 MIN
minutes
1 2 3 4 5 6 7 8 9
Default x
To make program change
Hold Recall Time Set [26] [NEXT] [SELECT] [MEMORY] [END]
/2 MIN/DISABLE
------ 30 SEC/1 MIN/1.5 MIN
30 seconds 1 minute 1
minute30 2 minutes disable
Default x
To make program change
Programmable External
Paging Access Tone [27] [NEXT]
[
SELECT
]
[
MEMORY
]
[
END
]
1
-------- ENABLE/DISABLE
Default To make
p
ro
g
ram chan
g
e
Enable x
Disable
DTMF Receiver Check [28] [NEXT][SELECT] [MEMORY] [END]
appears
1
L- -
[--- ENABLEIDISABLE
until the desired DTMF receiver
Default To make program change
DTMF receiver 1, 2 1 2
Enable x
Disable
Programmable Toll Prefix [29] [NEXT] [SELECT] [MEMORY][END] 1
'- - - -- WITH 11 WITHOU
T
Default To make
p
ro
g
ram chan
g
e
With I x
Without 1
Programmable secret
Auto Dial [30] [NEXT] [SELECT] [MEMORY] [END]
L - - NO SECRET! SECRET
Default To make
p
ro
g
ram chan
g
e
No secret x
Secret
Station Program Clear [98] [NEXT] [MEMORY] [END]
System Clear [99] [NEXT] [MEMORY] [END]