Panasonic KX-TA824 User manual

Set Up the KXTA 824 for Built In DISA Auto Attendant
Step 1. Set the CO Line for DISA/AA Service
Programming mu t be done from exten ion 101
Leave the hand et in the cradle and pre the PROGRAM button
Dial *#1234 (STAR POUND 1 2 3 4)
Dial 414
Pre the SP-PHONE button
Dial * (STAR) Set all line for DISA or dial a pecific CO for individual control.
Pre the AUTO ANS/MUTE button until the di play fla he “CO *:DISA:OGM-“
Dial 1
Pre the AUTO DIAL/STORE button
Pre the HOLD button
Step 2. A ign Dialed Digit to Exten ion Jack
Dial 501
Pre the SP-PHONE button
Dial 1
Pre the AUTO ANS/MUTE button until the di play read “1:Jack-“
Dial the jack number (01, 02 etc.)you want the call to go to when the caller dial 1.
Pre the AUTO DIAL/STORE button to ave your etting.
Pre the SP-PHONE button and the di play will change to “2:Not Stored”
Dial the jack number you want the call to go to when the caller dial 2.
Pre the AUTO DIAL/STORE button to ave your etting.
Repeat the tep until you have entered all jack location you need.
Pre the HOLD button when done.
Example: Dial 1 for Jack 03
Dial 2 for Jack 06
Dial 3 for Jack 02
If unu ed, be ure to a ign Dial 7 for Jack 01 to prevent Modem Acce .
Special Note:
If unu ed, be ure to a ign Dial 9 and Dial 0 to Jack 01 (Receptioni t)
Otherwi e, Dial 9 or Dial 0 may allow a caller to go back out on another line.
Note:
CPC Di connect Service (>250m ) from Telco i required for abandoned call .

Step 3. A ign Auto Attendant to DISA
Dial 500
Pre the SP-PHONE button
Pre the AUTO ANS/MUTE button until the di play fla he “With AA”
Pre the AUTO DIAL/STORE button
Pre the HOLD button
Step 4. A ign Call Waiting to DISA
Dial 506
Pre the SP-PHONE button
Pre the AUTO ANS/MUTE button until the di play fla he “Call Waiting”
Pre the AUTO DIAL/STORE button
Pre the HOLD button
Step 5. A ign “No Dial” to DISA
Dial 510
Pre the SP-PHONE button
Pre the AUTO ANS/MUTE button until the di play fla he “Di connect”
Pre the AUTO DIAL/STORE button
Pre the HOLD button
Pre the PROGRAM button to exit programming.
Special Note:
If you u e the DISA feature on a particular CO Line, the CO Line CAN NOT ring
in on any phone .
The incoming call will be an wered by the DISA feature only.
Step 6. Record your OGM Me age
Follow procedure below…..

How to Record Out Going Me age (OGM)
Programming/Recording mu t be done from exten ion 101
Leave the hand et in the cradle and pre the PROGRAM button
Now rai e the hand et
Dial 911
When you hear the beep…Begin recording your Out Going Me age
When you are done recording…Pre the AUTO DIAL/STORE button
The y tem will play your Out Going Me age back to you
If it ound OK then hang up.
If you want to re-record the OGM, dial 1 and begin recording after the beep.
When you are done recording…Pre the AUTO DIAL/STORE button
How to Li ten to an Out Going Me age (OGM)
Programming mu t be done from exten ion 101
Leave the hand et in the cradle and pre the PROGRAM button
Now rai e the hand et
Dial 921
The y tem will play your Out Going Me age back to you
If you want to repeat the OGM, dial 1 and it will plat again.
Hang up
How to Era e an Out Going Me age (OGM)
Programming mu t be done from exten ion 101
Leave the hand et in the cradle and pre the PROGRAM button
Dial 901
Pre the AUTO DIAL/STORE button
Pre Hold
Pre the Program button
Pre Hold