Panasonic TY-ST42PT3S User manual

Pedestal
TY-ST42PT3S TY-ST42PT3K
Wall stand
TY-ST42PW1
Mobile stand
TY-ST42PF3
Wall-hanging bracket (vertical)
TY-WK42PV1
Wall-hanging bracket (angled)
TY-WK42PR1
Ceiling unit
TY-CE42PS1
Speakers
TY-SP42PM3W TY-SP42PWD3W

How to use this manual
Some notes on how to read this manual
In this manual, the number such as "1, 2, 3,..." appears to the left of each step.
Go ahead in numerical order.
Indicates a situation where incorrect handling may result in death or serious injury for the person performing the
installation.
Indicates a situation where incorrect handling may result in breakdown or damage to physical objects.
Contains more detailed information than in the steps in the main text. Be sure to read the notes.
Other notes
• More-detailed explanations and supplemental information for the installation procedures are given on the right.
* Be sure to read not just the steps on the left, but the information on the right as well.
• At the very beginning of the installation procedure, there are illustrations for assembling various accessory parts
on the Wide Plasma Display. Refer to them when installing.
• Each installation procedure for accessory parts is preceded by a brief description of the procedure. During the
pro-cedure, refer to the description if necessary.
• Each installation procedure for accessory parts is followed by an explanation of how to remove the Wide Plasma
Display.Refer to this when it is necessary to remove the accessory parts from the Wide Plasma Display and reposition
it.

Before installing
Be sure to read through these instructions before starting the installation.
The installation should be only performed by a professional person.
If any parts are not installed correctly, the display unit may fall, possibly resulting in damage and personal injury.
Failure to follow Warning instructions may result in damage and personal injury.
Make sure that all safety conditions regarding strength at installation are observed.
If the installation strength is insufficient, the display unit may fall and personal injury may result.
Do not install in places which are unable to bear the weight of the display.
If the strength of the floor and wall at the site of installation is insufficient, the display unit may fall, possibly
resulting in damage and personal injury.
A caution indicates special precautions against actions which may result in fire or electric shock.
Do not install in places subject to humidity, dust, oil fumes, condensation or excessive heat.
These factors may adversely affect the Wide Plasma Display, possibly resulting in fire or electric shock.
Do not install theWide Plasma Display horizontally with the screen facing up, or sideways or upside
down.
Installing the screen other than in the conventional viewing setting may cause heat to build up inside the display
and possibly result in fire.
Two persons are required to install and remove the display unit.
The display unit is heavy and at least two persons are needed to handle it safely.The display unit may drop and
personal injury may result if one person attempts to install it without assistance.
Maintain a space of at least 10 cm respectively at the top, bottom and sides of the display unit and at
least 1.9 cm at the rear of the display unit.
The display unit has air outlet holes at the top and air intake holes at the bottom and rear.These holes must not
be blocked, nor airflow not be obstructed.Otherwise fire may result.

Tools list
The tools in the following tables are necessary for complete assembly.
Before attempting to install the accessories, make sure you have the following tools on hand.
Optional parts list
Pedestal
Wall stand
Mobile stand
Wall-hanging
bracket (vertical)
Wall-hanging
bracket (angled)
Ceiling unit
–––
–––
Plus screw driver Clean cloth Drill Measure Level gauge
–
–
–
–
–
–
Pedestal
Wall stand
Mobile stand
Wall-hanging
bracket (vertical)
Wall-hanging
bracket (angled)
Ceiling unit
Wire or Chain M6 bolt x 6

Accessory list
TY-ST42PT3-S
TY-ST42PT3-K
TY-ST42PW1
Pedestal Wall-hanging bracket (vertical)
Wall-hanging bracket (angled)
Wall stand
1
2
4
5
TY-WK42PR1
TY-WK42PV1
TY-ST42PF3
Mobile stand
3
TY-CE42PS1
Ceiling unit
6
TY-SP42PM3W
TY-SP42PWD3W
Speakers
7
For information on the wiring of the Wide Plasma Display after installing accessories, be sure to refer to the
documentation that comes with the Wide Plasma Display.

Parts list
Check the part number before performing the installation procedure.
Base Assembly screw(M5-20) x 4
Assembly screw (M5-30) x 4
Pedestal
Wall pedestal
Holding bracket
Allen key (accessory)Fixing screw (M5) x 2
Pan head bolt with hex socket
(M8-45) x 4 Insulating spacer x 4
Toothed pan washer x 4Fixing screw (M5) x 2 Assembly
Wall stand
Pole x 2
Wood screw x 2
Black screw x 2
Band x 2
Black screw x 2
Clamp x 4

Wall-hanging bracket unit Fixing screw (M5) x 2
Pan head bolt with hex socket (M8-45) x 4
Tooted pan
washer x 4 Insulating spacer x 4
Wall-hanging bracket unit Fixing screw (M5-35) x 2
Pan head bolt with hex socket (M8-45) x 4
Tooted pan
washer x 4 Insulating spacer x 4
Allen key (accessory)
Allen key (accessory)
Wall-hanging bracket ( vertical )
Wall-hanging bracket ( angled )
Holder Shelf Stand base Support x 2
Cable strap x 5 Bolt (M8)x 4 Assembly screw (M6-16)
and spring washer x 4 each
Assembly screw (M5-15) x 4 Assembly screw (M5-30) x 4
Mobile stand

Ceiling unit Fixing bolt (M8-12) x 2
Ceiling unit
Allen key
Fixing bolt (M8-100)
Spring washer
Washer pan nut (M8)
Fixing screw (M5) x 2
Fixing bolt (M8-20) x 2
Cable tie x 2Pan head bolt with hex socket
(M8-45) x 4
Toothed pan washer x 4
Insulating spacer x 4
Points to note during installation
•This ceiling unit is for mounting a Wide Plasma Display to a ceiling for viewing purposes.
Do not use it for any type of installation other than ceiling mounting.
•In order to ensure correct, problem-free operation of the Wide Plasma Display, do not install the Display in any of
the following places:
•Next to sprinklers or sensors
•Where it may be subject to vibration or shocks
•Near high-voltage wires or electric motors
•Where it may be in direct contact with air from heaters
•When installing this ceiling unit, use a fixing method appropriate to the type of ceiling.
•Insert the mains plug for the Wide Plasma Display into a mains socket which is close and easily accessible.
•Provide adequate ventilation so that the temperature around the display does not rise above 40°C (104 F°).
If there is insufficient movement of the air inside the display, heat may build up inside the display and fire may result.
•For U.S.A (TH-42PW3 / TH-42PWD3 only)
If the connection cable cannot reach the Display when it has been installed to the wall, use the 15 m cable (TY-
SCP15C03) which is sold separately.
Speakers
Speaker x 2 Bracket mounting
Assembly screw (M4-10) x 12
Mounting bracket
(right) x 2
Mounting bracket
(left) x 2 Sponge x 2
Speaker cable
(20 cm) x 2

Dimensions of the display unit
S-VIDEO
VIDEO VD HD PR/CR/R PB/CB/B Y/G
L
R
L
R
AUDIO AUDIO
AUDIO
SERIALTUNER IN
PC INCOMPONENT/RGB IN
AV IN
1020
920
50
610 518
615
89
50
22
18.5
35.7
70.69 296
18 18 18 18 20 53.86
98
39.43
4646
489
44
112.2 65390.9
Units : mm
To connect the power cord and others, refer to the documentation that comes with the Wide Plasma Display.

1-1
Pedestal
TY-ST42PT3S
TY-ST42PT3K
Assembly diagram
CONTENTS
Instruction of the installation...................... 1-2
1.Assembling the pedestal.................................... 1-2
2.Attaching the pedestal to the display unit .............. 1-2
3.Fixing the display unit ....................................... 1-3

1-2
Instruction of the installation
Assembling the pedestal
Attaching the pedestal to the display unit
Ensure that the poles sit
flush with the bottom of
the base.
Place the display face
down on a cloth clean
and free from other
foregin particles, and
then proceed to the next
step.
Spread a clean cloth over a level floor or base, and place on it the display
unit face down.
Remove the screws and covers.
Keep them in a safe place for possible future use.
1
Put the poles into the outer holes on the base, and fasten the four
screws.
1
Assembly screw
(M5-20) x 4

1-3
Insert the four screws, two on each side, into the holes in the back
of the display unit and screw them into the holes on the inserted poles.
3
Front
Rear
Fixing the display unit
Insert the two poles at the top of the pedestal into the holes in the base
of the display unit as shown in the illustration below.
2
Fixing the display unit to a desk.
Screw the bands to the pedestal with screws.
1
Screw the bands to edge of a desk with screws.
2
Assembly screw
(M5-30) x 4
If you are using a
wooden desk, then use
the wood screws.
Use the appropriate
screws for the type of
material of the desk.
Band x 2
Black screw x 2
Wood screw x 2

1-4
Fixing the display unit to the wall
Insert the screws and clamp into the holes at the back of the display
unit.
1
Use a strong wire or chain commercially available to fix the display unit
to a solid area of the wall or pillar.
2
Black screw x 2
Clamp x 4

2-1
Assembly diagram
CONTENTS
Description ................................................... 2-2
Instruction of the installation...................... 2-3
1.Assembling the wall stand.................................. 2-3
2.Fixing the insulating spacers to the display unit...... 2-4
3.Attaching the wall stand to the display unit ............ 2-6
4.Fixing the display unit to the wall ......................... 2-7
Removing the display unit........................... 2-8
Wall stand
TY-ST42PW1

Description
Installation diagram
400 (15
3
/
4
)
610 (24
1
/
64
)
1116.5 (43
61
/
64
)
611.5 (24
5
/
64
)
744 (29
19
/ 64 )
1020 (40
5
/ 32 )
560 (22
1
/ 16 )
390 (15
23
/ 64 )89 (3
33
/ 64 )
19 (
3
/ 4 )
*100
Units : mm
2-2
* A clearance of at least 100mm at the top of the display unit should be provided.

Instruction of the installation
Assembling the wall stand
Refer to the holding
bracket installation
measurements in the
drawing left.Ensure that
the wall is able to bear
the weight at each of the
4 upper and lower
installation locations.
Add reinforcement if any
of these locations are
not strong enough.
Check the strength of the installation location.
The height measurements marked ** are particularly important. Do not
attempt to set up the pedestal in a location where these dimensions and a
clearance of at least 100 mm at the top of the display unit should be provided.
1) On the wall, measure and mark a height 650 mm above the floor;
2) Measure and mark the location 475 mm horizontally to the right of
the mark you made in 1). Measure and mark points 180 mm and 360
mm above each mark (for a total of six marked locations);
3) Drill a hole at each of the six marked locations on the wall.
1
390 (1523/64)
180 (73/32)
631.5 (247/8)
611.5 (241/16)
180 (73/32)
400 (153/4)
Wall installation holes
(4 locations)
Spare wall installation holes
(2 locations)
560 (22 1/16)
744 (2919/64)
Floor surface

** **
Units : mm
Ensure an area of at least
650 mm by 1,230 mm in
length at the location
where you plan to install
the holding bracket.
The holding bracket has
6 slits through which the
bracket can be fixed to a
wall with screws.
If the wall material does
not allow sufficient
strength by using six
installation holes, use
some of the spare holes.
However, depending on
the construction material
used at the place of
installation, cracks may
develop if the screws are
inserted too close to
each other.
2-3

Fix a M6 screw, through any of the slits in the bracket, into the
corresponding hole in the wall.
Using a level along the top or bottom edge, ensure that holding bracket is
horizontal.
2
Fix the screws through the slits into the remaining three holes.
3
Provisionally tighten the fixing screws.
4
Fixing the insulating spacers to the display
unit
1) Spread a clean cloth over a level floor or base, and place it on the
display unit face down.
2) Remove the screws and covers.
Keep them in a safe place for possible future use.
1
The holding bracket must always be installed.It prevents the display unit from
falling after installation.
If the screws protrude
more than 5 mm, it will
not be possible to
properly install the
display unit.
Carefully place the Wide
Plasma Display face
down on top of a clean
cloth, which has been
spread over a flat
surface with no other
objects on it, and then
proceed to the next
step.
2-4

Remove the four screws.
2
As shown in the illustration, use the supplied "Allen key" to fasten the
screw through and , then screw the four to the display unit.
3
Pan head bolt with
hex socket
Toothed pan washer
Insulating spacer
2-5

Attaching the wall stand to the display unit
Insert the two poles at the top of the wall pedestal into the holes in the
base of the display unit as shown in the illustration.
1
Insert the four screws, two on either side, into the holes in the back
of the display unit and fasten them into the holes in the inserted poles.
2
The screws and covers
may be required later if
the display unit is moved
and mounted directly to
a wall, so keep them in
a safe place so that they
will not get lost.
Assembly screw
(M5-30) x 4
2-6