Panasonic TY-S42PX20U User manual

TQZH507 Printed in Japan
1. Align the support pole insertion holes of the plasma TV with the support poles (1 each), and
lower the plasma TV until the poles stop. Slightly lift the left and right sides of the plasma TV and
remove the corner protection pads attached to the bottom.
2. Fasten the plasma TV and support poles using assembly screws (black screws) (× 4)
Ref. Description
Top crosspiece
Bottom panel
Side panel (Left)
Side panel (Right)
Rear cord cover
Glass shelf
Cord holder
TY-S50PX20U
Part No.
TBLA0117
TBLH0550
TBLA0104
TBLA0103
TBLB3110
TKGA0129
TBLA3217
TY-S42PX20U
Qty. Part No.
1 TBLA0116
1 TBLH0548
1 TBLA0104
1 TBLA0103
1 TBLB3080
1 TKGA0127
1 TBLA3184
REPLACEMENT PARTS LIST
To maintain appearance we recommend the following:
Painted Surfaces:Use a damp cloth for cleaning. Do not use any abrasive or chemically treated cleaners.
NOTE:As with all indoor furniture, this unit should not be exposed to direct sunlight, extreme temperatures
or moisture, as this can result in serious irreparable damage.
When making a part (s) inquiry or for out of warranty purchases
please quote part no. & description.
Placement
•To thread wiring, remove the terminal cover and pass wires along the
grooves in the rear cord cover, along the groves in the left and right
side panels, and along the groves in the cord holder under the glass
shelf.
∗Some equipment may have short cords. In such an instance, thread
the wiring over the minimum distance, as indicated by the dotted line in
the diagram.
•After threading wiring, fasten with cord clamps (×6) so that the cords
do not protrude from the grooves. Finally, attach the terminal cover.
If there are any cord clamps left over, store them carefully. You will
need them if you use the unit to house more equipment in the future.
A study of the assembly instructions will not only save you time, but may prevent possible damage to your
new stand.
Assistance may be required for some assembly procedures.
CAUTION : THIS STAND IS DESIGNED ONLY FOR USE WITH APANASONIC PLASMA TV.
APPLIED MODEL : TH-42PX20, TH-50PX20
Use with other appliances may result in instability causing possible injury.
Replacement parts
Assembly screws Glass shelf fastening screws Glass shelf support fastening
screws (Black screws) ( × 4)
Rear cord cover fastening
screws (Black screws) ( × 3)
Assembly screws (Black screws)
Support pole (Right) Support pole (Left) Cord clamps
THEA118 × 4 THEA102N × 8
XSB4+12FZ × 7XST5+12 × 4 XYN5+F55FZ × 4
TBLA3194 × 2
TBLA3197 × 1 TBLB3111 × 6
Bottom cap (Right)
TBLB3107 × 1
Bottom cap (Left)
TBLB3108 × 1
Screws
XTB4+10B × 4
TBLA3196 × 1
Support pole fastening screws
Glass shelf supports (Right) Glass shelf supports (Left) Casters (Wheels)
TBLA3195 × 2 TBLB3074 × 4
Your hardware pack contains / Replacement parts
∗Wire over the minimum distance
Cord clamps Power cord
(Back)
∗The top glass shelf is specifically for the center speaker and AV
amp. If you place a video deck here, it may badly affect the picture.
PANASONIC SERVICES COMPANY
20421 84th Avenue South, Kent, Washington 98032 Tel. : [phone] Fax : [phone]
2003 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 Tel. : [phone]
2003 Matsushita Electric Industeial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
Assembly Instructions
TY-S42PX20U
TY-S50PX20U
Display stand
IMPORTANT
For improvement purposes, design and specifications are subject to change without notice.
STEP 1 Plasma TV installation and fastening method
∗Install the plasma TV by referring to the following illustration.
∗Do not hold the plasma TV at the bottom of the front panel.
Lift and
remove
Support pole
(Left)
Assembly screws
(Black screws)
Corner
protection pad
Support pole (Right)
Support pole
insertion hole
∗Position by placing your hands at the
points indicated in the illustration.
STEP 2 To use with equipment such as a video deck
The tools required:
Plus (Phillips) (+) screwdriver

TQZH507 Printed in Japan
Assembly & Placement
Manual
Assembly
4. Attach the caution label to one
glass shelf on the right side,
facing the front. Insert the glass
shelf in parallel with the grooves
in the glass shelf supports (left
and right), and securely fasten
to the bottom of the (left and
right) glass shelf supports using
the glass shelf fastening screws
(×4). Fit the other glass shelf
in the same manner.
TY-S42PX20U
TY-S50PX20U
Model No.
1. Securely insert the casters (×4) into the bottom panel.
2. Align the dowels of the side panels (left and right) with the dowel holes in the bottom panel and
insert.
Rear cord cover
Notches
Rear cord cover fastening
screws (Black screws)
Glass shelf support fastening
screws (Black screws)
Dowel holes
Glass shelf
supports (Left)
1. Align the dowels in the glass shelf supports (left) (×2)
with the dowel holes in the side panel (left) and insert.
Securely fasten with the glass shelf support fastening
screws (black screws) (×1).
2. Attach the glass shelf supports (right) in the same
manner.
3. Insert a cord holder in parallel with the glass shelf supports
(left and right), and align the dowels of the cord holder
with the dowel holes in the glass shelf supports. Attach
the other cord holder to the other glass shelf supports in
the same manner. Glass shelf supports
(left and right)
Cord holder
Dowel / hole
Caution label
Glass shelf
Glass shelf
fastening screws
Top crosspiece
Support pole (Right)
Support pole
fastening screws
Notches
1. Align the support pole (right) with the notch
on the right side of the top crosspiece, and
securely fasten with the support pole fastening
screws (×2) using a Phillips head (+)
screwdriver. Fasten the support pole (left) to
the left side in the same manner.
2. Insert the rear cord cover fastening screws
(black screws) (×3) into the screw holes on
the back of the top crosspiece and partially
fasten. Slide the 3 notches in the rear cord
cover behind the screws and securely fasten
the screws.
3. Align the dowels of the side panels (left and
right) with the dowel holes in the top crosspiece
and insert. Securely fasten with assembly
screws (×4).
Side panel (Left)
Dowels
Dowel holes
Front
Bottom panel
Side panel (Right)
Casters
Dowels
Dowel holes
Assembly
screws
∗Position the glass shelf such that the caution
label is on the top surface, on the near side.
∗Do not load either glass shelf with equipment
weighing over 12 kg (26 Ib.). Do not load the
bottom storage area with equipment weighing
over 20 kg (44 Ib.).
STEP 1 Attaching of bottom panel, side panels and casters
STEP 2 Attaching of top crosspiece and rear cord cover
Side panel
(Right)
Side panel
(Left)
∗∗
∗∗
∗Do not use electric powered screwdrivers.
STEP 3 Attaching of glass shelf and cord holder
The tools required:
Plus (Phillips) (+) screwdriver
Side panel
(Left)