Panasonic ET-WBC100 User manual

Specifications
Range of
adjustment
Horizontal swing angle ±5°
Vertical tilt angle ±5°
Horizontal tilt angle ±5°
Vertical slide amount Image size between 2.03 m [80 in]
1
and 2.29 m [90 in]:
-10 mm – +10 mm [-13/32 in – +13/32 in]
Image size between 2.29 m [90 in](exclusive) and 3.05 m [120 in]:
-10 mm – +40 mm [-13/32 in – +1 9/16 in]
Forward/backward slide amount 0 mm – 270 mm [0 in – 10 5/8 in]
Horizontal slide amount -41 mm – 49 mm [-1 5/8 in – 1 15/16 in]
2
External dimensions Width 491 mm – 519 mm [19-11/32 in – 20-7/16in]
Height 210 mm – 245 mm [8-9/32 in – 9-21/32in]
Depth 395 mm – 665 mm [15-9/16 in – 26-3/16in]
Weight Approx. 8 kg (17.64 lbs)
1 For the aspect ratio of 4:3, it is 1.78 m [70 in].
2 The horizontal slide range includes a middle portion that cannot slide.
Applicable projectors
PT-CMZ50
Note
•This illustration is prepared on the assumption that the projected image size and position have been aligned to fit full in the screen.
•This illustration is not drawn to scale
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 1/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

Structural components (ET-WBC100)
This is a wall mount bracket (Model No.: ET-WBC100) for installing the projector to a wall.
Parts name Form (number of parts) Applications
Wall mount bracket x 1
This wall mount bracket is installed to the wall to support the
entire product.
In addition to forward/backward and vertical slide adjustment, it
allows vertical and horizontal tilt adjustment and horizontal swing
adjustment of the projector.
Mount cover These are attached to the wall mount bracket.
Projector mount
bracket kit x 1
This is used to install the projector to the wall mount bracket.
It consists of a projector mount bracket and a connecting plate.
It allows horizontal slide adjustment of the projector.
Screws Screw with captive washer (M6×16)
x 4 Used to secure the projector mount bracket kit to the projector.
Flanged screw (M4×10)
x 4 Used to secure the projector mount bracket kit to the wall mount
bracket.
Projector
dropprevention kit
Screw with captive washer (M6×16)
x 1
Prevents the projector from falling.
Use one of the two wire ropes.
Wire rope
(3.0 mm [1/8 in] wire diameter,
750 mm [29 17/32 in] length)
x 1
Wire rope
(3.0 mm (1/8 in] wire diameter,
660 mm [25 31/32 in] length)
x 1
Flat washer (M6)
x 1
Template sheet x 1 Used to determine positions of the screw holes for securing the
wall mount bracket to the wall.
•Store small parts in an appropriate manner, and keep them away from children.
•Tightening torque for the screw is M4: 1.25 ± 0.2 N·m (excluding the flanged screws), M6: 4 ± 0.5 N·m.
•When tightening up the screws, use a tool such as a torque screwdriver. Do not use electric screwdrivers or impact screwdrivers.
Attention
•Installation work should onle be carried out by the certified personnel.
•Do not install in a location that is not strong enough.
•Read the "Installation Instructions" throughly and then preform the operation correctly and safely.
•If products are no longer being used, they should be dismantled and removed by the certified personnel as soon as possible.
•Dispose of the packaging materials properly after taking the product out of it.
Anchor Bolt Center (Fall Prevention Wire Attaching Position)
アンカーボルト中心線（落下防止用ワイヤーロープ取付位置）
Image Center
投写画面中心
Wall Mount Bracket Center
壁掛け取付金具中心
DPQP1457ZA/X1
Mount cover (L) x 1 Mount cover (R) x 1
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 2/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

Structural components (ET-PKC300B)
This projector mount bracket (Model No.: ET-PKC300B) is included in wall mount bracket (Model No.: ET-WBC100.)
This is a projector mount bracket (Model No.: ET-PKC300B) used to replace the projector mount bracket of an existing wall mount bracket.
Parts name Form (number of parts) Applications
Projector mount
bracket x 1 This is used to install the projector to the wall mount bracket.
Screws Screw with captive washer (M6×16)
x 4 These are used to secure the projector mount bracket to the
projector.
Screw with captive washer (M4×14)
x 5
These are used to secure the connecting plate, which is removed
from the existing wall mount bracket, to the projector mount
bracket.
Projector
dropprevention kit
Screw with captive washer (M6×16)
x 1
Prevents the projector from falling.
Use one of the two wire ropes.
Wire rope
(3.0 mm [1/8 in] wire diameter,
750 mm [29 17/32 in] length)
x 1
Wire rope
(3.0 mm [1/8 in] wire diameter,
660 mm [25 31/32 in] length)
x 1
Flat washer (M6)
x 1
•Store small parts in an appropriate manner, and keep them away from children.
•Tightening torque for the screw is M4: 1.25 ± 0.2 N·m (excluding the flanged screws), M6: 4 ± 0.5 N·m.
•When tightening up the screws, use a tool such as a torque screwdriver. Do not use electric screwdrivers or impact screwdrivers.
Attention
•Dispose of the packaging materials properly after taking the product out of it.
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 3/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

Dimensions
(Unit : mm [inch])
10 [13/32]
40 [1 9/16]
665 [26 3/16]
Vertical slide
Horizontal slide
Factory default position Factory default position
245 [9 21/32]
210 [8 9/32]
395 [15 9/16]
Forward/backward
slide
519 [20 7/16]
491 [19 11/32]
511 [20 1/8]
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 4/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

The illustration shows the ET-WBC100 mounted on PT-CMZ50.
(Unit : mm [inch])
40-300
[1 37/64-11 13/16]
210
[8 17/64]
157-207
[6 3/16-8 5/32]
395-665 [15 35/64-26 3/16]
421-691 [16 37/64-27 13/64]
421 [16 37/64]
47.5 [1 7/8]
449 [17 43/64]
491 [19 21/64]
198.5-288.5
[7 13/16-11 23/64]
172 [6 49/64]
56.6
[2 15/64]
495 [19 31/64]
247.5 [9 3/4]
52-102 [2 3/64-4 1/64] (Factory default : 92 [3 5/8])
195–245
[7 43/64-9 41/64]
367-417 [14 29/64-16 27/64]
Arm extension amount : 0-270 [0-10 5/8]
(Projection surface to rear surface of CMZ50
(lens warranty range)) : 0-181 [0-7 1/8])
418 [16 29/64]
286.5 [11 9/32]
131.5
[5 11/64]
173 [6 13/16]
165 [6 1/2]
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 5/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

Dimension of screw holes used for securing the wall mount bracket.
(Unit : mm [inch])
25.5 [1]
16 [5/8]
20 [25/32]
68.5 [2 45/64]
131.5 [5 11/64]
209 [8 15/64]
418 [16 29/64]
47.5 [1 7/8]
15 [19/32]
173 [6 13/16]
86.5 [3 13/32]78.5 [3 3/32]
38 [1 1/2]
63.5 [2 1/2]
18 [4/64]
8 [5/16]
20 [25/32]
10
20
Wall mount bracket
center
Image center
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 6/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

The dimensional relationship between the screen and projector is shown below.
Determine the installation position on the wall based on the “Dimensional relationship diagram” and the
“Dimensional relationship”.
The projected image size can be adjusted by changing the distance between the screen and the projector.
Dimensional relationship diagram
<For PT-CMZ50>
SH
L
L1
D
SD
H1 L5
H2
SW
L3
L4
L2
Wall mount bracket center →
←
→Center axis of
horizontal swing
adjustment
SH
Image center
Note
•The illustrations of projectors in this manual are for informational purposes only. The appearance may differ from the actual product.
•This drawing is not in exact scale.
SH Projected image height
SW Projected image width
SD Projected image size
LProjection distance (distance from the screen surface to the mirror reflection surface1)
DDistance from the wall surface to the screen surface
L1 Distance from the screen surface to the back surface of the projector
L2 Distance from the back surface of the projector to the wall surface
L3 Distance (225 mm [8-27/32 in]) from the center axis of horizontal swing adjustment to the back surface of the projector
L4 Distance from the wall surface to the center axis of horizontal swing adjustment
L5 Distance (47.5 mm [1-7/8 in]) from the image center to the wall mount bracket center
H1 Distance from the top edge of the projected image to the center of screw holes (on the lower side) used for securing the wall mount
bracket
H2 Distance from the top edge of the projected image to the center of screw holes (on the upper side) used for securing the wall mount
bracket
1 The mirror reflection surface cannot be seen from the outside because it is located inside the projector.
Attention
•To prevent obstruction of the intake and exhaust vents, install the projector with a clearance from walls and objects. For details about the
required distance from surrounding walls and objects, refer to the operating instructions for your projector. If you are installing the projector
in a sealed space, be sure to provide additional air conditioning equipment and ventilation equipment. Insufficient ventilation will result in an
accumulation of heat and may activate the projector’s protection circuit.
•Avoid setting up in places which are subject to sudden temperature changes, such as near an air conditioner or lighting equipment (studio
lamps, etc.).
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 7/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

Dimensional relationship
To use a projected image size not listed in the tables, check the projected image size SD (m) and calculate the
value using the formulas provided in “Formulas for calculating dimensions”.
<For PT-CMZ50>
Dimensions in the tables are values when Digital Zoom Extender function is disabled by setting the [POSITION]
menu →[SCREEN ADJUSTMENT] →[DIGITAL ZOOM EXTENDER] to [OFF] on the projector.
Unit: m
Projected image size [Aspect ratio 16:10] LL1 H1
1
H2
1
SD SH SW
2.03 [80 in] 1.077 1.723 0.41 0.010 0.346 0.519
2.16 [85 in] 1.144 1.831 0.43 0.033 0.358 0.531
2.29 [90 in] 1.212 1.939 0.46 0.055 0.370 0.543
2.41 [95 in] 1.279 2.046 0.48 0.078 0.381 0.554
2.54 [100 in] 1.346 2.154 0.50 0.10 0.393 0.566
2.79 [110 in] 1.481 2.369 0.55 0.15 0.417 0.590
3.05 [120 in] 1.615 2.585 0.59 0.19 0.441 0.614
Projected image size (Aspect ratio 16:9) LL1 H1
1
H2
1
SD SH SW
2.03 [80 in] 0.996 1.771 0.42 0.020 0.407 0.580
2.16 [85 in] 1.058 1.882 0.44 0.043 0.422 0.595
2.29 [90 in] 1.121 1.992 0.47 0.067 0.438 0.611
2.41 [95 in] 1.183 2.103 0.49 0.090 0.453 0.626
2.54 [100 in] 1.245 2.214 0.51 0.11 0.469 0.642
2.79 [110 in] 1.370 2.435 0.56 0.16 0.500 0.673
3.05 [120 in] 1.494 2.657 0.61 0.21 0.532 0.705
Projected image size (Aspect ratio 4:3) LL1 H1
1
H2
1
SD SH SW
1.78 [70 in] 1.067 1.422 0.41 0.007 0.344 0.517
1.91 [75 in] 1.143 1.524 0.43 0.032 0.358 0.531
2.03 [80 in] 1.219 1.626 0.46 0.058 0.371 0.544
2.16 [85 in] 1.295 1.727 0.48 0.083 0.384 0.557
2.29 [90 in] 1.372 1.829 0.51 0.11 0.398 0.571
2.41 [95 in] 1.448 1.930 0.54 0.13 0.411 0.584
2.54 [100 in] 1.524 2.032 0.56 0.16 0.425 0.598
2.79 [110 in] 1.676 2.235 0.61 0.21 0.451 0.624
1 Values in the tables are based on the factory default height position of the arm.
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 8/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

Formulas for calculating dimensions
To use a projected image size not listed in “Dimensional relationship”, check the projected image size SD (m)
and use the respective formula to calculate the value.
Values obtained with the following formulas contain a slight error.
When calculating the value using image size designation (value in inches), multiply the value in inches by
0.0254 and substitute it into SD in the formula.
<For PT-CMZ50>
Aspect ratio 16:10 16:9 4:3
Screen height (SH) =0.530 x SD =0.490 x SD =0.6 x SD
Screen width (SW) =0.848 x SD =0.872 x SD =0.8 x SD
Projection distance (L) =0.1782 x SD + 0.0485 =0.1831 x SD + 0.0485 =0.2017 x SD + 0.0485
Distance from screen surface to back surface
of the projector (L1) =0.0100 + (L-0.4105)
Distance from back surface of the projector
to wall surface (L2) =L1 + D
Distance from wall surface to center axis of
horizontal swing adjustment (L4) = L1 + L3 + D or = 0.0100 + (L-0.4105) + L3 + D
Distance from top edge of projected image
to center of screw holes (on lower side)
used for securing the wall mount bracket
(H1)
=0.0933 x SD + 0.1564 =0.1231 x SD + 0.1564 =0.1056 x SD + 0.1564
Distance from top edge of projected image
to center of screw holes (on the upper side)
used for securing the wall mount bracket
(H2)
=0.0933 x SD + 0.3294 =0.1231 x SD + 0.3294 =0.1056 x SD + 0.3294
ET-WBC100/ET-PKC300B
Wall Mount Bracket
As of February 2023 9/9
WBC100/PKC300BG_STR_T01_14/02/2023
S P E C F I L E
TENTATIVE

1
Panasonic Connect Co., Ltd. 2022
Feature 01 |Communicate Clearly and Comfortably
⚫Delivers a large80-inch imagefrom about 1 cm (1/3 in)4
⚫5,200 lm3and WUXGA resolution makes text and graphics easy to read in brightly lit rooms
⚫Quiet 26 dB operation (QUIET Mode) reduces distractions when the projector is nearby
⚫Stylish cabinet(availablein black/white) has no lens protrusion and harmonizes with any décor
Feature 02 |Flexible, Versatile, and Easy to Install
⚫Lightweight wall-mountbracket option ships partially preassembled for easy installation
⚫Powered center/periphery focus via remote control simplifies post-installation adjustment
⚫Digital Zoom Extender and Digital ImageShift function enables convenient adjustment after installation
⚫Supports wide-aspect 2560 x 1080 (21:9)5and 3240 x 1080 (27:9)5input signals
⚫Accepts 4K input signals1
⚫Connect a second projector/monitor via HDMI™ output terminal
Feature 03 | Eco-friendly Long-Term Operation
⚫No light-sourceor filter maintenancerequired for 20,000 hours6, reducing waste
⚫Watts-per-lumen efficiency is approx. 31 %7better than other lamp-based short-throw models
AVAILABLE FROM
CY2023 Q2
PT-CMZ50
Laser Projector DeliversBig Pictures from
Ultra-ShortDistances with Minimal Shadowing,
Easy Installation, and ConvenientAdjustment
Model PT-CMZ50
Light output
5,200 lm3
Resolution WUXGA (1920 x 1200 pixels)
Light source
Laser diodes
Dimensions
(W x H x D)
495 mm x 160 mm x 421 mm (19 1/2˝ x 6 19/64˝ x 16 37/64˝)
(excluding feet and protrusions)
495 mm x 176 mm x 421 mm (19 1/2˝ x 6 15/16˝ x 16 37/64˝)
(with feet at shortestposition)
Weight Approx. 9.5 kg (20.9 lbs)
Operation
noise 35 dB (NORMAL/ECO), 26 dB (QUIET)
Note: Design and specification subject to change without notice. Release date varies by country or region.
1 4K/30p signals are supported via HDMI™ and DIGITAL LINK terminals. 2 Requires optional AJ-WM50 Series Wireless Module (sold separately). Availability may vary by countryor region. 3 When [PICTURE MODE] is set to [DYNAMIC] and [LIGHT POWER] is set to [NORMAL]. Measurement, measuring conditions, and method of notation are
all compliant withISO/IEC 21118: 2020 international standards. Value is average of all products when shipped. 4 Value is the distance from projector body to wall.5 A 2560 x 1080 (21:9) input signal is displayed at 1920 x 810 (21:9), and a 3240 x 1080 (27:9) input signal at 1920 x 640 (27:9). 6 Around this time, light output will have
decreased to approximately 50 % of its original level ([PICTURE MODE]: [DYNAMIC], [DYNAMIC CONTRAST] set to [2], temperature 30 ° C [86 ° F], elevation 700 m [2,297 ft] with 0.15 mg/m3of particulate matter). Estimated time until light output declines to 50 % varies depending on environment. Filter can be washed and reused up to two
times. Filter cleaning cycle: 20,000 hours (under dust conditions of 0.08 mg/m3), 10,000 hours (under dust conditions of 0.15 mg/m3). 7Based on a comparison between PT-CMZ50 (max. power consumption 325 W, brightness 5,200 lm)and PT-TW381R (max. power consumption 300 W, brightness 3,300 lm).
12
1
Tentative

Panasonic Connect
Media Entertainment Business Division
PT-CMZ50 introduction
February 2023 Ver2.0
1. This presentation is for product introduction purposes only. Please refer to spec file, webpage or l eaflet for detailed information.
2. Unauthorized reproductionis prohibited.

3
Panasonic Connect Co., Ltd. 2022
PT-CMZ50
Laser Projector DeliversBig Pictures from
Ultra-ShortDistances with Minimal Shadowing,
Easy Installation, and ConvenientAdjustment
AVAILABLE FROM CY2023 Q2
PT-CMZ50
5,200lm
WUXGA (1920 x 1200)
12
1 4K/30p signals are supported via HDMI™ and DIGITAL LINK terminals.
2 Requires optional AJ-WM50 Series Wireless Module (sold separately).

CMZ50
Concept
Project a large 80-inch image from
about 1 cm (1/3 in)1. Avoid screen
shadows and give remote and
on-site participants a clear view,
even in brightly lit spaces. Ceiling and
wall-mount options simplify installation
while smooth UX streamlines usability
in the classroom, office,and beyond.
Communicate Clearly and Comfortably
WUXGA images from ultra-short distances
Feature 01
Flexible, Versatile, and Easy to Install
Partially preassembled wall-mountoption
and powered center/periphery focus
Feature 02
Deliver big, clear pictures
from ultra-short distances
Eco-Friendly Long-Term Operation
Energy-efficient operation reduces
cost and environmental impact
Feature 03
Tentative
1 Value is the distance from projector body to wall.

55
Panasonic Connect Co., Ltd. 2022
暫定版
CMZ50 Product Position
Ultra-Short-Throw 5,200 lm1CMZ50
Creates Opportunities in Diverse Spaces
Zoomlens
LMZ460
Zoom lens
(1.36–1.64:1)
4,600–4,200 lm
VMZ71
Zoom lens
(1.09–1.77:1)
7,000–5,200 lm
TMZ400
Short-throw
(0.43:1)
4,000 lm
CMZ50
Ultra-short-throw
(0.235:1)
5,200 lm1
Ultra-short-throw
0.235:1 0.43:1 1.09–1.77:1 1.36–1.64:1
Tentative
1 When [PICTURE MODE] is set to [DYNAMIC] and [LIGHT POWER] is set to [NORMAL]. Measurement, measuring conditions, and method of notation are all compliant with ISO/IEC 21118: 2020 international standards.
Value is average of all products when shipped.

66
Panasonic Connect Co., Ltd. 2022
暫定版
Eco-friendly Long-term Operation
Reduces Environmental Impact, from Unboxing to EOL
More
Efficient Longer Lasting Less Waste
Watts-per-lumen efficiency about
31 %1better than other lamp-based
short-throw models
Includes ECO Mode to further
reduce power consumption
No lamp disposal thanks
to long-lasting laser
Light source and filter
don’t require maintenance
for about 20,000 hours2
1 Based on a comparison between PT-CMZ50 (max. power consumption 325 W, brightness 5,200 lm) and PT-TW381R (max. power consumption 300 W, brightness 3,300 lm). 2 Around this time, light output will have decreased to approximately 50 % of its original level ([PICTURE
MODE]: [DYNAMIC], [DYNAMIC CONTRAST] set to [2], temperature 30 ° C [86 ° F], elevation 700 m [2,297 ft] with 0.15 mg/m3of particulate matter). Estimated time until light output declines to 50 % varies depending on environment. Filter can be washed and reused up to two
times. Filter cleaning cycle: 20,000 hours (under dust conditions of 0.08 mg/m3), 10,000 hours (under dust conditions of 0.15 mg/m3).
Tentative
Filter can be washed and
reused, reducing waste

7
Panasonic Connect Co., Ltd. 2022
Delivers a Large 80-inch Image from About 1 cm (1/3 in)1
Feature 01 | Communicate Clearly and Comfortably
Challenge
-Need to display content as large as possible
-Installation space is limited by room size or ceiling
obstructions (lights, cameras, microphones, etc.)
-Need to avoid screen shadows andlens dazzling
CMZ50 Solution
✓Projects an 80–120 in (2.03–3.05 m) image,
ideal for rooms with limitedinstallationspace
✓Installs almost flush to the wall with optional wall
mount avoiding obstructions on the ceiling
✓Ultra-short-throwdesign limitsshadowing,
ideal for exhibitions/studios where people
are close tothe screen
Tentative
1 Value is the distance from projector body to wall.
1

8
Panasonic Connect Co., Ltd. 2022
•High brightness improves image visibility in
environments with bright LED lighting
•WUXGA resolution smooths and sharpens fine text for
clear visibility when viewed at a distance
Panasonic WUXGA model compared to a competitive model with
Full HD-equivalent resolution achieved via shifting technology.
5,200lm1at WUXGAfor clear image visibility Sharp, high-contrast pictures in well-lit rooms
1 When [PICTURE MODE] is set to [DYNAMIC] and [LIGHT POWER] is set to [NORMAL]. Measurement,
measuring conditions, and method of notation are all compliant with ISO/IEC 21118: 2020 international standards.
Value is average of all products when shipped.
•High 3,000,000:11Dynamic Contrast optimizes image
expression for realistic depth and dimensionality
•System Daylight View enhances image visibility according
to ambient light levels in the room
1 Full On/Full Off. When [PICTURE MODE] is set to [DYNAMIC] and [DYNAMIC CONTRAST] is set to [1].
Feature 01 | Communicate Clearly and Comfortably Tentative
competitive model
System Daylight View OFF System Daylight View ON

9
Panasonic Connect Co., Ltd. 2022
•Heat-resistant laser light source contributes to a significant
reduction in fan and exhaust noise
•Operation noise is almost indiscernible even
when seated close to the projector
•Stylish cabinet design without lens protrusion
•Black or white body suits a variety of spaces, from
classrooms and meeting rooms to museums
Lamp-based
model →CMZ50
Operation noise130 dB 4 dB
Lower 26 dB
Operating noise is
perceived to be about
half that of the
lamp-based model2
Quiet Design Limits Distractions Stylish Cabinet Blends into Your Space
Feature 01 | Communicate Clearly and Comfortably Tentative
1 Based on a comparison between PT-CMZ50 (26 dB) and PT-TW381R (30 dB) in QUIET Mode. 2 Decibel
value is a logarithmic expression, meaning that a 4 dB change results in the perception that operating
noise is approximately halved(or doubled) compared to the original value.