Panasonic NA-F75G6 User manual

© Panasonic Corporation 2015 Unauthorized copy-
ing and distribution is a violation of law.
Order No. APIN150902CE
Fully Automatic Washing Machine
Model No. NA-F75G6
Model No. NA-F70G6
Model No. NA-F65G6
Model No. NA-F62G6
Model No. NA-F75S6
Model No. NA-F70S6
Product Color SRB : SUS Silver
LRB : Silver
FRB : Flower Red
Destination India
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions----------------------------------------------- 2
2 Specifications ----------------------------------------------------- 3
3 General/Introduction -------------------------------------------- 3
4 Technical Descriptions ----------------------------------------- 4
5 Installation Instructions ---------------------------------------- 7
6 Operating Instructions-----------------------------------------10
7 Troubleshooting Guide ----------------------------------------12
8 Disassembly and Assembly Instructions ---------------17
9 Wiring Connection Diagram ---------------------------------21
10 Exploded View and Replacement Parts List -----------22

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
2
1 Safety Precautions

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
3
2 Specifications
3 General/Introduction
3.1. "AUTO RESTART" function
Model NA-F75S6 NA-F70S6 NA-F75G5 NA-F70G5 NA-F65G5 NA-F62G5
Rated Voltage and Frequency 230 V / 50 Hz
India
Rated Power
Consumption
Wash 430 W 423 W 430 W 423 W 408 W 400 W
Spin 250 W 250 W 250 W 250 W 250 W 250 W
Power Consumption Amount 117 Wh 113 Wh 117 Wh 113 Wh 110 Wh 107 Wh
Color Siliver SUS Silver Silver Flower Red
Outer Dimension
Body W: 520 mm x D: 530 mm x H: 744 mm
Installation W: 525 mm x D: 571 mm x H: 969 mm W: 525 mm x D: 571 mm
x H: 929 mm
Water Supply Pressure 0.03 to 1MPa (0.3 to 10 kgf / cm2)
Standard Water Consumption 110 L 107 L 110 L 107 L 101 L 99 L
Standard Capacity Wash 7.5 Kg 7.0 Kg 7.5 Kg 7.0 Kg 6.5 Kg 6.2 Kg
Spin 7.5 Kg 7.0 Kg 7.5 Kg 7.0 Kg 6.5 Kg 6.2 Kg
Weight with Accessories 31 Kg 30 Kg
Weight with Packing 35 Kg 34 Kg

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
4
4 Technical Descriptions
4.1. Features and Technical information
4.1.1. Operation Time of each course
4.1.2. Product special features
1. Aqua Beat
2. Load sensor
3. Detergent indicator
4. Water level sensor
5. Reservation timer
6. Softener compartment
7. Large size cassette lint filter
8. Detergent compartment
9. Automatically power shut off
10. Fault indication (LED blinking, lightening)
11. Buzzer on-off function
12. Overflow detecting
13. Child Lock function
14. Auto Re-start function
15. Air Dry
16. ECO navi
17. Temp-Setting
18. Aqua Wave Pulsator
19. Gentle Hand Wash
20. Double Inlet
21. Petit active foam system
4.1.3. Weight Sensor
The weight is sensed by the moving force of the Pulsator, which changes a capacitor pole and releases a signal wave. The wave is
changed into a pulse number from which the clothes weight is sensed. Prior to weight sensing for Normal and Strong program, the
machine runs without water by spinning the Pulsator to left and right for 4.2 seconds (ON 0.3 second- OFF 0.4 second).
The motor stops (OFF), a water system counts the pulse number, then calculates the accumulated pulse numbers for drawing water
into the tub over a defined level. The dial will indicate High wash level.
Course Time Capacity
1 Normal Approx. 38 - 45 min Rated load
2 Quick Approx. 18 min 2.0 Kg or less
3 Baby-Care Approx. 43 - 52 min Rated load
4 Bed Sheets Approx. 59 min 4.2 Kg or less
5 Gentle Hand Wash Approx. 41 min 1.2 Kg or less
6 Tub Hygiene Approx. 133 min -
7 Daily Sari Approx. 40 - 46 min 1.2 Kg or less
8 Power Soak Approx. 83 - 150 min Rated load
9 Air Dry Approx. 90 min 2.0 Kg or less

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
5
4.2. Function Control
Clothes quantity checking, wash level indication and detergent consumption indication.

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
6
4.3. Power consumption and current
The following requirements shall be met in accordance with Product Standard.
(1) Washing
Note : To determine the value, integrate the data for 2 min after 5 min from starting motor and convert based on duty ratio of
water flow for that period.
(2) Spinning
Note : To determine the value, integrate the data for 2.5 min after 3.5 min from starting motor and convert based on duty ratio of
water flow for that period.
Model Voltage Frequency Power source Water load Rated load
NA-F75G6/S6 230V 50Hz Current (A) 1.7 + 0.4 2.15 + 0.5
Power consumption (W) 340 + 80 430 + 50
NA-F70G6/S6 230V 50Hz Current (A) 1.7 + 0.4 2.15 + 0.5
Power consumption (W) 340 + 80 423 + 50
NA-F65G6 230V 50Hz Current (A) 1.7 + 0.4 2.15 + 0.5
Power consumption (W) 340 + 80 408 + 50
NA-F62G6 230V 50Hz Current (A) 1.7 + 0.4 2.15 + 0.5
Power consumption (W) 340 + 80 400 + 50
Model Voltage Frequency Power source No load Rated load
NA-F75G6/S6
NA-F70G6/S6
NA-F65G6
NA-F62G6
230V 50Hz
Current (A) 0.9 + 0.2 1.1 + 0.2
Power consumption (W) 215 + 50 250 + 50

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
7
5 Installation Instructions
5.1. Installation

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
8

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
9
5.2. Child Lock program
5.3. The option component for installation
Service pressure hose unit
• AXW1251-201---1 m
• AXW1251-202---2 m
• AXW1251-203---3 m
• AXW1251-205---5 m
• AXW1251-250---0.5 m

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
10
6 Operating Instructions
6.1. Operations Panel

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
11

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
12
7 Troubleshooting Guide
7.1. Test Running without water
< Method to test running without water >
1. Set the power switch to [OFF].
2. Press and hold both the [Process] and [Power Soak] buttons with one hand.
3. Press the power ON button.
4. Release the your fingers from the buttons and power switch which you pressed in steps 2. and 3. above.
(Check A can be carried out in this state with your fingers released.)
5. Within three seconds, press the [Process] button to set to the desired check procedure as follows.
Number of times
the [Process]
button is pressed
Check
Procedures
Check contents Lamp illumination condition Operation condition
• End signal
• Auto power-off
• The end buzzer sounds three times
after operation is finished.
• The lamps as shown in figure will simul-
taneously flash on and off and the
power will automatically be switched off.
• Abnormal in memory storage.
It should be indicated [02].
• In case of the end buzzer is [switched
off],[Child Lock] will be switched on.
• Abnormal signal of
memory:
[H05] will be displayed.
• Indication of [H17] is
given for thermister
error.
• Even if there is no water in the tub, the
washing operation will continue for six
minutes.
• Press the [Program] button to change
the current.
Every 1 second, wash current will be
changed.
[Normal] - [Gentle Hand Wash]
Normal current : LED display [1] for 5
seconds.
Gentle Hand Wash current : LED dis-
play [5] for 5 seconds.
• Pressing [Power Soak] is able to switch
over program(agitation water supply
hot water supply).
• Spin operation check.
• Abnormal signal of lid
switch and SF switch.
• The spinning operation will continue for
six minutes.
• SF SW 2 OFF(Open the lid) [hours]
lamp On.
• SF SW 1 OFF(Open the lid) [Reserve]
lamp On.
• SF SW 1 and 2 are both OFF. Buzzer
notifying that the lid is open while the
tub is rotating.

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
13
• Water level to be deter-
mined by cloth amount
detection is to be 1 rank
higher than the normal
level.
• Pressing the [PowerSoak] switch
selects whether to use correction func-
tion or not. ( [L0] or [L1])
• Press [Start/Pause] button to set water
level raise.
• Clear belt tension data.
It shows belt tensile
force.
• b0 :Belt tension rank 0 (Shipping) Good
Condition.
• b1 :Belt tension rank 1 A little bit loose.
• b2 :Belt tension rank 2 Very loose.
• The error indication dis-
play for past two times.
• [E] shall be indicated initially, press
[Power Soak] button to change last time
to time before last and return to E as ini-
tial mode.
• If there were some abnormal alarm in
the past , [U] or [H] and some number
shall be indicated mutually.
• [U12] , [H15] and abnomal test check
will not be recorded.
• The display for running
number
• [C] should be indicated initially, press
[Power Soak] button to change indica-
tion of digit of operation times.
• Press once : Digit (Thousand-Hundred)
Press twice : Digit (Ten-One)
ex: Press once : shows [12](One thou-
sand two hundred thirty four)
• Running number count including all
[Wash Rinse Spin] processes.
• When exceeding 9999 times, Digit
(Thousand) is indicated.
• Contiune [A000] to [A999]
Number of times
the [Process]
button is pressed
Check
Procedures
Check contents Lamp illumination condition Operation condition

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
14
7.2. Table Of Errors

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
15
7.3. Table of Troubleshooting

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
16
7.4. Symptoms are not trouble.

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
17
8 Disassembly and Assembly Instructions
8.1. Suspension replacement
1. Open the lid and remove the panel A packing.
2. Remove 2 screws mounting side of the body B.
3. Remove 2 screws mounting back of the body B.
4. Rise up the body B against the wall.
5. Pull up and remove the suspension from the body A.
note:
Return the air hose to same as initial position.
8.1.1. About the grease application of a suspension unit
1. Prepare the Grease.
2. The place which applies grease
•Damper Grease

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
18
•CVT-B Grease
Please do not let this grease adhere to a cap and slide part absolutely.
The part becomes a damage.
It becomes a cause of abnormal vibration.
8.2. The option component tool for a repair service.
8.2.1. HW-42(Pulsator screw remover tool)
• It uses when removing the screw of a pulsator.
How to use
1. The shaft(HW-4202) and the T-handle(HW4201) are attached.
2. It uses attaching a Flat Bit(HW4205) or Plus Bit(HW4204) to A sets.
3. Remove the screw of the pulsator.

NA-F62G5 / F65G5 / F70G5 / F75G5 / F75S6 / F70S6
19
8.2.2. HW-25K (Flange nut remover tool)
• It uses when removing the screw of a Spinner Shaft Flange Nut.
How to use
1. Attach the "Fixer" to "Spinner Shaft Flange Nut".
2. Attach the "Hammer".
3. Rotate the "Hammer". (If a Fixer is struck, the nut will loosen.)

NA-F62G6 / F65G6 / F70G6 / F75G6 / F75S6 / F70S6
20
8.3. Valve Unit & Geared Motor replacement
1. Remove screws of the Geared Motor.
2. Pull out the Geared Motor and Valve Unit at the same time.
3. Geared Motor and Valve Unit made be straight.
4. Bend Valve Unit and Geared Motor angle of 90 degrees.
5. Valve Unit and Geared Motor come off easily.