Panduit PES400 User manual

PA28998A01_00 Page: 1 of 2 11-2017
PES400
PA28998A01
Rev. 00 11-2017
PANDUIT EMBOSSING SYSTEM
QUICK START GUIDE
© Panduit Corp. 2017
WARNING
TO REDUCE THE RISK OF INJURY, USER MUST READ
INSTRUCTION MANUAL
*The Operation Manual, PA28981A01, is located in the “Documentation“ folder on the
USB drive provided in the accessory bag. Page and figure numbers below reference
the Operation Manual.
*Easy-Mark Plus™ version 1.2 or higher, also located on the provided USB Drive, is
required to operate the PES400 Embossing System.
Quick Start Guide Checklist for Changing Plate Sizes and Embossing
□Unlock cover with cover key and open machine cover.
□Remove the top clamp by loosening both thumbscrews. see [Figure 1] on [Page 18].
□Remove the top weight(s) [Figure 1]. (For 1.72 wide plates, complete Step 4.2.4 on [Page
18] first.)
□Remove any remaining plates. (For 1.72 wide plates, complete Step 4.2.4 on [Page 18]
first.)
□Loosen the right-hand side knob and slide the right-hand side wall to open the loader.
[Figure 1and Figure 5]
□Change the Plate Support Block if needed, Step 4.2.5 on [Page 19] to determine correct
plate support block.
□Put correct top clamp on and tighten.
□Adjust the Gate Height [Page 23].
□Remove top clamp.
□Position Guide Rails [Page 26].
□Load the plates [Page 28] with Easy Feed Humps up.
□Put the top weight on [Figure 20].
□Put the top clamp back on and tighten.
□Align the back edge of Side Eject Guide Plate [Page 28].
□Close machine cover.
□Adjust the insert of the external hopper to corresponding slot or use corresponding insert
[Figure 24] on [Page 30].
□Turn on PES400 [Page 31].
□Run Easy-Mark Plus [Page 31]. ***Version 1.2 or higher required***
□Emboss one plate [Page 34] to review if embossing force adjustment [Page 34] is needed.
□If any error happens, check the Error Codes on [Page 38] to debug the issue.

© Panduit Corp. 2017 QUICK START GUIDE PES400
PA28998A01_00 Page: 2 of 2 11-2017
Plates
Plate
Height
(in)
Guide Rail
Size Block
(Figure 14)
Plate
Width
(in)
Plate Support
Block and
Top Clamp)
Top Weight
(Figure )
Hopper
Divider
Position
and Inserts
MMMP350W38-M,
MMP350W38-M316,
MT350W38-M316
.38 Narrow
3.5 Long Narrow .38
MMP172W38,
MT172W38-M 1.72 Short Short
Divider
@ .75”,
using Insert
.38 x 1.72
MMP350HW54-MAL,
NCMP35W54T20-AL .54 Medium 3.5 Long Medium .54
MMP350-M, MMP350-M316,
MMP350H-M,
MMP350H-M316,
MMP350H-MAL,
MT350-M .75 Wide
3.5 Long Wide .75
MMP172-M,
MT172-M, 1.72 Short 2 Short Use Insert
.75 x 1.72
MMP350W17-M,
MT350W17-M,
MT350W17-D-4HL 1.72 None
1/16”
(1.6mm)
clearance
3.5 Long Extra-
Wide 1.72
MMP337W53-MAL-4,
MMP337W71-MAL-3 2.12 3.37 Long Extra-
Wide Not Needed
Email:
[e-mail]
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com
www.panduit.com
US & Canada Technical Support:
Tel: [phone]
Panduit Europe
EMEA Service Center
Almelo, Netherlands
Tel: [phone]
Fax: [phone]