Panduit DAP3 Series User manual

DAP3 PAR #:
DAP3BB-S0
DAP3BC-00
DAP3BC-00-55
DAP3BC-S0
DAP3BC-S0-4
DAP3BC-S0-5
DAP3BC-S0-55
DAP3BC-S0-5U
DAP3BC-S0-6
DAP3BC-S3-4
DAP3BC-S3-5
DAP3BC-S3-6
DA A ACCESS POR
INS ALLA ION INS RUC IONS
© Panduit Corp. 2019
B21102
Rev: 00 3-2019
Data Access Ports (DAP), provide end users a safe and secure means to maintain and
monitor performance of P Cs, VFDs, and industrial networks.
Integrated security features shall prevent the disruption of service or unwanted
access by unauthorized personnel. Non-arc flash certified personnel can access networks
within the panel which reduces cost, increases efficiency, and promotes overall safety.
Furthermore, the new, innovative circular design allows for quick and easy installation.
NOTE: In the interest of higher quality and value, Panduit products are continually
being improved and updated. Consequently, pictures may vary from the
enclosed product.
NOTE: Updates to this Instruction Manual may be available.
Check www.panduit.com for the latest version of this manual.
TO REDUCE THE RISK OF INJURY, USER MUST READ
INSTRUCTION MANUA
Safety Information
Failure to comply with the warnings and
information in this manual could result in
product failure, electrical shock, severe
injury or death.
Warning
• Always de-energize power before accessing an electrical enclosure.
• Always follow safety and lockout/tagout procedures when working on or near electrical
systems and equipment.
• Use proper personal protective equipment (PPE) when working around sources of
hazardous electrical energy.
• Do not use this product outside of the specified performance and environmental limits.
• This product must be installed by a qualified worker.
• Always comply with local installation codes and standards.
Information de Sécurité
• Toujours éteindre l'alimentation électrique avant d'accéder à un boîtier électrique.
• Suivez toujours les procédures de sécurité et de verrouillage / étiquetage (lockout/tagout)
quand vous travaillez sur ou à
proximité de systèmes et d'équipements électriques.
• Utilisez un équipement de protection individuelle approprié (EPI) lorsque vous travaillez
autour de sources d'énergie électrique dangereuse.
• N'utilisez pas ce produit en dehors des performances spécifiées et des limites
environnementales.
• Ce produit doit être installé par un ouvrier qualifié.
• Respectez toujours les codes et les normes d'installation locaux.
Page: 1 of 2
© Panduit Corp. 2019 INS ALLA ION INS RUC IONS DAP
Shown: DAP3BC-G3-5 Shown: DAP4BC-G3-5
DAP4 PAR #:
DAP4BB-G0
DAP4BC-G0
DAP4BC-G0-4
DAP4BC-G0-5
DAP4BC-G0-5U
DAP4BC-G0-6
DAP4BC-G3-4
DAP4BC-G3-5
DAP4BC-G3-6
DAP4BC-X0
echnical Specifications
Warning: Do not use this product outside of the specified performance and environmental
limits. Failure to comply with these specifications could result in product failure,
personal injury, or death.
Standards
UL 50E ENC OSURES FOR E ECTRICA EQUIPMENT,
ENVIRONMENTA CONSIDERATIONS
UL 50 ENC OSURES FOR E ECTRICA EQUIPMENT,
NON-ENVIRONMENTA CONSIDERATIONS
CSA C22.2 NO. 94.1 ENC OSURES FOR E ECTRICA EQUIPMENT,
NON-ENVIRONMENTA CONSIDERATIONS
CSA C22.2 NO. 94.2 ENC OSURES FOR E ECTRICA EQUIPMENT,
ENVIRONMENTA CONSIDERATIONS
UL 508A STANDARD FOR INDUSTRIA CONTRO PANE S
CSA C22.2 NO. 14-13 INDUSTRIA CONTRO EQUIPMENT
IEC 60529 DEGREES OF PROTECTION REQUIRED BY ENC OSURE
Application
Degree of Protection For Flat Surface Mounting in a TYPE (U , NEMA and CSA)
4, 4X, 12, 13, IP65 and IP66 Enclosures.
www.panduit.com
echnical Support:
1-800-777-3300
Email: [email protected]

Quarter Turn atch for
locking cover
© Panduit Corp. 2019 INS ALLA ION INS RUC IONS DAP © Panduit Corp. 2019 INS ALLA ION INS RUC IONS DAP
General Dimensions
DAP3 Data Access Port
Alignment
Tabs (4)
DAP4 Data Access Port
Page: 2 of 2
Install Padlock for extra security
(sold separately)
LOCK RING
The features on the lock ring shown can be lined up
with the scribe lines on the inside of the panel door for
proper orientation of the Data Access Port.
2.914”
Dia.
LOCK RING
The features on the lock ring shown can be lined up
with the scribe lines on the inside of the panel door for
proper orientation of the Data Access Port.
HANGING BOX:
To be installed after wiring
for the GFCI is completed.
PUNCHED HOLE:
1) Use 2-1/2 inch conduit hole punch for DAP3 Data Access Ports
2) Use 3-1/2 inch conduit hole punch for DAP4 Data Access Ports
LOCK RING
SERRA ED NU S BOL S
Installation Instructions:
1. Punch recommended hole size per application.
2. Install Data Access Port in front side of panel.
3. Install ock Ring over supplied Bolts (3) [not shown].
4. Secure ock Ring with supplied Serrated Nuts (3) by torquing the nuts to 32 IN* B.
5. Insure all nuts are torqued to 32 IN* B after initial torque down.
6. Wire electrical components per local electrical code.
7. Install Hanging Box with supplied Bolts (2) [only applicable on the DAP4 Data Access
Port with GFCI outlet].
Punch Die Numbers
DAP3: DAP4:
Greenlee 738BB (mild steel) Greenlee 741BB (mild steel)
Greenlee 745H-2-1/2 (stainless steel) Greenlee 745H-3-1/2 (stainless steel)
Panduit DAP3PUNCH-MS (mild steel) Panduit DAP4PUNCH-MS (mild steel)
Panduit DAP3PUNCH-SS (stainless steel) Panduit DAP4PUNCH-SS (stainless steel)