PAR EverServ ES500 User manual

PAR ES500® POS Terminal Setup Guide
[©Copyright 2013 ParTech, Inc. All rights reserved.] page 1 772231901
Thank You!
Thank you for purchasing a PAR point-of-
sale system. We are confident that our
technology solutions will contribute to your
business success.
Examine the Shipment:
Use the invoice to ensure all equipment is
present.
Report any missing or damaged
equipment to your PAR salesperson.
Inventory Components:
Ensure you have the following items in your
POS order:
POS terminal
AC power cord
2 Serial adapter cables (C8200)
Dual Cash Drawer Adapter cable (C2355)
1. Power LED 2. Touch Screen and LCD
3. Power Switch 4. Customer Display
5. Credit Card Reader 6. Cable Well
32
POS Dimensions
ES500 POS Terminal Overview
Remove Terminal from
Box
Remove the terminal from the box as
shown.
4
3
2
1
C2355 Dual Cash Drawer Adapter Cable (Right) TwoC8200 Adapter Cables (Left)
5
Note: The ES500 POS terminals have two non-powered RJ-
50 10-pin (COM 1 & 2) serial connections. COM 3 and COM
4 are powered RJ-50 serial ports. COM 3 is 5V and COM 4
is 12V. The ES500 has no DB9 serial ports - only RJ-50
10P10C-pin serial ports. When using peripherals with DB9
serial connections with the ES500, an adapter cable must
be used. An example would be between the terminal and
the printer serial interface cable. The adapter cable (PN
C8200) comes in approximately 10” length. A C2355 (Dual
Cash Drawer Adapter Cable) cable is shipped with each
terminal and additional cables can be purchased from PAR.
Inventory Equipment
Power Cord
ES500 Register
6

PAR ES500® POS Terminal Setup Guide
[©Copyright 2013 ParTech, Inc. All rights reserved.] page 2 772231901
Service and Support
For service and support during or after installation,
contact the PAR phone center at 1-800-382-6200.
Battery Warning
A lithium coin-type battery is installed on the ES500
motherboard. If this battery is replaced, it must be replaced
with an equivalent battery type. Dispose of the used battery
according to local disposal instructions.
Connect AC Power Cord to
Terminal
1. Lay the terminal on its back on a clean, flat
surface.
2. Locate the AC power cord.
3. Connect the AC power cord to the POS
terminal power supply. The power supply is on
the underside of the terminal.
4. Connect the other end of the AC power cord
to an uninterruptible power supply (UPS)
Connect Peripherals to POS Terminal
1. Lay the terminal on the counter on its back
with the bottom facing you.
2. Tilt the top cover up.
3. Connect your peripherals to the POS terminal.
Refer to the Cable Connections diagram.
4. Place register upright.
5. Power on the POS terminal. The power button
is located on the bottom left side of the top
cover.
6. Power on the peripherals.
Plug Power Cord into
Power Brick
Cable Connections
CD1= RJ-12 Cash
Drawer Port
LAN Connection
USB Ports
COM 1 COM2
(Connect C8200
Cable)
VGA
Power
Button
Input/Output Connections
M5100:
Two RJ-50 10-pin Serial Ports (COM 1 & 2)
Two RJ-50 Serial Ports available with +12 or 5V
(COM 3 & 4)
One RJ-12 Cash Drawer port
Four (4) Standard 2.0 USB ports
One 10/100/1000 Ethernet Network port
One VGA port for optional second play
One +19V DC power input jack
(Connect C8200 Cable)
COM 3 (5V) COM 4 (12V)
DC Power
(from
Power
Supply)
Cable Well
Additonal Translations
Additional translations can be found at PAR’s website:
http://www2.partech.com/en/service-support/driver-
page.cfm