Paradyne 9000-A2-GN10-20 User manual

TM
1
1-Slot Assembled Access Unit
Installation Instructions
Document Number 9000-A2-GN10-20
March 1997
Before You Begin
Make sure you have:
A dedicated, grounded ac outlet within 6 feet of the access unit that is protected by
a circuit breaker.
A clean, well-lit, and ventilated site that is free from environmental extremes.
One to two feet of clearance for cable connections.
An operable DDS/frame relay network connection.
An async (asynchronous) terminal or PC (personal computer).
Package Checklist
Verify that your package contains the following:
One-slot Frame Relay Access Unit
One-slot access unit mounting hardware, if ordered
Power cord with desktop power transformer
COM port-to-PC cable (14)
One V.35 DTE adapter cable for Port 1 (1)
Warranty card
RJ48S modular cable for network access (14)
Only one DTE cable is provided. Additional cables may need to be ordered; see Cables
You May Need to Order
on the next page for cable ordering information.

2
Cables You May Need to Order
If connecting to a . . . Order a . . .
Terminal/Printer (DB25
interface/connector – EIA-232
connection)
COM Port-to-terminal/printer cable
DTE with a V.35
interface/connector V.35 DTE adapter cable for another port (Port 1 or Port 2)
LAN adapter COM Port-to-LAN adapter cable
Contact your sales representative to order these cables.
Safety Instructions
Please read the EMI warning and Important Safety Instructions that come with this unit.
Installing the Power Cord
1. Insert the 4-prong plug into the POWER jack. When inserting the plug at the rear of
the access unit, align the plug with the notch above the POWER jack. Make sure the
locking tab snaps securely into the jack.
496-14939-01
POWER
PORT 1 PORT 2
COM NET BKP
Power Cord /
Transformer
Insert the 3-prong plug
into an ac outlet.
OK ALM
9621 The front panel
OK LED lights.
2.
3.
3-Prong
Grounded
AC Outlet
Locking
Tab
POWER
COM

3
Connecting the COM Port to a
User or Management Interface
The access unit must first be directly connected to a PC or async (or other
VT100-compatible) terminal. You can set up just the communication port and protocol,
or you can completely configure the unit. Refer to the User’s Guide for configuration
information.
1. Connect a PC or async terminal to the access unit’s COM port.
497-14940a-0
1
COM Port-to-PC Cable
or COM Port-to-Terminal/Printer
POWER
COM
To Connect to a PC, Async Terminal *
or Printer: a. Insert the 8-pin end of the
cable into the COM port.
Insert the other end of the cable
into the user or management
interface.
c. Press Return on the keyboard to
display the Main Menu.
b.
2. Reload the factory-set configuration options.
3. Edit the Communications Port options.
4. Edit the Node IP Address option if management will be via a Telnet session, through
a LAN adapter, router, or terminal server.
5. Edit the following User Interface configuration options, if needed (e.g., External
Device if connecting to an external modem, or Telnet Session).
6. Save the edited configuration options.
7. Reconnect the COM port cable based upon how the unit will be accessed.
496-14940
b
Router or
Terminal
Server
Gender Changer
to change DB25
Plug to Socket
LAN
AUX
Port
Async Terminal,
SNMP NMS, or PC
COM
Port-to-LAN
Cable
External
Modem PSTN
Network
or
To Connect to a LAN: To Connect to a
Router or Terminal
Server:
To Connect to an
External Modem:
POWER
COM
LAN
Adapter
COM Port-to-Terminal/Printer
Cable
or
or
Set the speed of the async or VT100-compatible terminal to 9.6 kbps so it matches the access
unit’s factory-loaded data rate, character length, and parity.
*

4
Connecting to the Network
496-1494
1
POWER
PORT 1 PORT 2
COM NET BKP
RJ48S
Jack
Insert the 8-pin connector on the
RJ48S network cable into
the NET (network) interface.
1. Insert the other end of the cable
into the RJ48S modular jack.
2.
Connecting to a DTE
If the DTE cable type is EIA-232E:
1. Connect the EIA-232E end of the DTE cable to PORT 1 or PORT 2.
496-1494
2
POWER
PORT 1 PORT 2
COM NET BKP
DTE
Cable
DTE
Cable
V.35 Adapter
Cable Frame
Relay
DTE
Frame
Relay
Router
or
FRAD
If the DTE cable type is V.35 (one is provided, another can be ordered):
1. Connect the plug to the V.35 end of the adapter cable.
2. Connect the EIA-232E end of the adapter cable to PORT 1 or PORT 2.
Verification Checklist
Did the OK LED light? If not, see
Troubleshooting in the User’s Guide.
Did you set the async terminal or PC speed to 9.6 kbps so it matches the access
unit’s factory-loaded speed, character length, and parity? If not, do so now.
Did the Main Menu appear on the terminal’s screen? If not, see
Troubleshooting in
the User’s Guide.
Verifying connection to a LAN adapter, router, FRAD, or external modem requires setup
and configuration; see
Setup in the User’s Guide.

5
Technical Specifications
Specification Criteria
Weight 2.59 lbs. (1.18 kg)
Power
Normal service voltage range 120 Vac12 Vac, 60 Hz 3
Physical Environment
Operating temperature
Storage temperature
Relative humidity
Shock and vibration
35°F to 122°F (1.7°C to 50°C)
4°F to 158°F (20°C to 70°C)
Up to 90% (noncondensing)
Withstands normal shipping and handling
Approvals
FCC Part 15
FCC Part 68
UL
CSA – Safety
Class A digital device
Refer to the equipment’s label for the Registration
Number.
Listed UL 1950
Certified CSA 22.2 No. 950-93
Interface/Connectors
NET – DDS and frame relay
network port
PORT – DTE synchronous
data ports
COM – communications/
management port
BKP – (reserved for future
use)
One 8-position modular keyed USOC RJ48S jack
Two 25-position (DB25) subminiature
EIA-232E/V.24/V.35 connectors
One 8-position modular unkeyed jack
One 8-position modular keyed jack
NET Port/Interface
Data rates
Services supported
56 kbps and 64 kbps clear channel
4-wire service

6
Specification Criteria
DTE Ports/Interfaces
Data rates
Interface types
Uncompressed: 4.8, 9.6, 14.4, 16.8, 19.2, 24, 28.8,
38.4, 48, 56, and 64 kbps
Compressed: 4.8, 9.6, 14.4, 16.8, 19.2, 24, 28.8,
38.4, 48, 56, 64, 128, 192, and 256 kbps
Two 25-pin EIA232E/V.24/V.35 connectors
COM Port/Interface
Data rates
Download rates
9.6, 14.4, 19.2, 28.8, and 38.4 kbps
38.4 kbps
Rear Panel
POWER
PORT 1 PORT 2
COM NET BKP
496-14886
Pin Assignments
NET Port/Interface
Function Circuit Pin #
Transmitted data to the local loop R 1
Transmitted data to the local loop T 2
Received data from the local loop T1 7
Received data from the local loop R1 8

7
COM Port/Interface
Signal Direction Pin #
DCE Transmit Clock (TXC) From DCE (Out) 1
DCE Received Data (RXD) From DCE (Out) 2
Signal Ground (SG) — 3
DCE Transmit Data (TXD) To DCE (In) 4
DCE Data Terminal Ready (DTR) To DCE (In) 5
DCE Carrier Detect (CD) From DCE (Out) 6
DCE Request to Send (RTS) To DCE (In) 7
DCE Received Clock (RXC) From DCE (Out) 8
DTE Ports/Interfaces
Signal Circuit
Mnemonic ITU/ CCITT # Direction
25-Pin
EIA-232E
Pin #
Shield — — — 1
Transmitted Data (TXD) BA 103 To DCE 2
Received Data (RXD) BB 104 From DCE 3
Request to Send (RTS) CA 105 To DCE 4
Clear to Send (CTS) CB 106 From DCE 5
Data Set (or DCE) Ready
(DSR) CC 107 From DCE 6
Signal Ground/Common (SG) AB 102A — 7
Received Line Signal Detector
(RLSD or LSD) CF 109 From DCE 8
Reserved for future use — — — 9
Not used — — — 10
Reserved for future use — — — 11
Reserved for future use — — — 12
Not used — — — 13
Reserved for future use — — — 14

8
DTE Ports/Interfaces (continued)
Signal Circuit
Mnemonic ITU/ CCITT # Direction
25-Pin
EIA-232E
Pin #
Transmitter Signal Element
Timing (TXC) DB 114 From DCE 15
Reserved for future use — — — 16
Receiver Signal Element
Timing (RXC) DD 115 From DCE 17
Local Loopback (LL) LL 141 To DCE 18
Not used — — — 19
Data Terminal (or DTE)
Ready (DTR) CD 108/1, /2 To DCE 20
Not used — — — 21
Ring Indicator (RI) RI 125 From DCE 22
Not used — — — 23
Transmitter Signal Element
Timing (TT) DA 113 To DCE 24
Test Mode Indicator (TM) TM 142 From DCE 25

*9000–A2–GN10–20*