Paramount Fitness clear o3 User manual

1
295 East Corporate Place • Suite 100 • Chandler, AZ 85225
Toll Free: 1.800.621.5886 • Phone: [phone]
Fax: [phone]
Param[email protected] • www.1Paramount.com
004-027-8780-00 REV111313
US and Foreign patents and patents pending see www.1paramount.com/about/patents/
WATER PURIFYING SYSTEM
INSTALLATION MANUAL
E
C
O
F
R
I
E
N
D
L
Y
P
A
R
A
M
O
U
N
T
C
E
R
T
I
F
I
E
D

2
CONTENTS
SAFETY INSTRUCTIONS ...................................................................................................................... 3
WHAT IS OZONE AND HOW DOES IT WORK.............................................................................. 4
SELECTING LOCATION & MOUNTING UNIT.................................................................................. 5
MAKING ELECTRICAL CONNECTIONS.......................................................................................... 6
ALTERNATE ELECTRICAL CONNECTION FOR
MULTI-SPEED PUMP WITHOUT A CONTROLLER OF TIME CLOCK.................................... 8
MAKING PLUMBING CONNECTIONS ..........................................................................................10
OPTIONAL SUBMERGED EQUIPMENT INSTALL......................................................................13
PLUMBING FOR THE CLEAR03 .....................................................................................................15
USING THE VENTURI INJECTOR METHOD.................................................................................15
SETTING AIR FLOW..............................................................................................................................16
EXTERNAL SAFETY AIR BLEED KIT INSTRUCTIONS (OPTIONAL).....................................16
BULB REPLACEMENT.........................................................................................................................17
TROUBLESHOOTING & SERVICE..................................................................................................19
CLEAR O3 PART NUMBERS .............................................................................................................21

3
IMPORTANT SAFETY INSTRUCTIONS: READ COMPLETELY BEFORE
PROCEEDING WITH INSTALLATION. SAVE THESE INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
CAUTION: READ AND FOLLOW ALL INSTRUCTIONS
WARNING:
• Follow all applicable electrical codes.
• A qualified licensed electrician should perform electrical hookup.
• Turn off power at main source before making any electrical
connections or servicing the unit.
• Use only liquid-tight flexible nonmetallic conduit for electrical
connections.
• A terminal marked G is located inside the supply terminal
compartment. To reduce the risk of electric shock, this terminal must
be connected to the grounding means provided in the electrical supply
service panel with a continuous copper wire equivalent in size to the
circuit conductors supplying this equipment.
• At least one lug marked “BONDING LUG” provided on the external
surface of the unit. To reduce the risk of electric shock, connect the
local common bond grid in the area of the pool or spa to this terminal
with an insulated or bare copper conductor not smaller than 6 AWG.
WARNING:
• ALWAYS wear safety glasses when using power equipment during the
installation process.
• Install at least 5 ft from pool or spa water using nonmetallic plumbing.
Mount ozone generator near pool equipment at least one (1) foot
above maximum water level to prevent water from contacting electrical
equipment. Install in accordance with the installation instructions.
• Short-term inhalation of high concentrations of ozone and long-term
inhalation of low concentrations of ozone gas can cause serious
harmful physiological affects. Do not inhale gas produced by this unit.
If installed in an enclosed space make sure to account for adequate
ventilation.
SAFETY INSTRUCTIONS

4
• UV LIGHT PRODUCED BY THIS UNIT IS HARMFUL TO
THE EYES AND MAY CAUSE BLINDNESS. DO NOT LOOK
DIRECTLY AT A LIT BULB!
NOTICE TO INSTALLER/OWNER:
• Save these instructions and deliver to pool owner when installation is
complete.
• Lamp contains mercury. Dispose of in accordance with local and state
regulations.
• Ozone is created from oxygen using a simple yet powerful system of UV bulbs, to
be used as a pure shock (oxidizer) for the swimming pool.
• Ozone is injected into the pool water using the Clear O3®suction injection system,
where the ozone enriched air is mixed with the water going into the pool circulation
pump. This creates a dynamic environment that best mixes the air and water at
high pressure as it is sent into the filter
• Once in the water, the ozone breaks down materials such as ammonia, oils, and
other non-living waste that are detrimental to chlorine’s function in the pool. This
occurs between the pump and filter and also in the filter. Chlorine is in a group
of the least stable elements and must be combined with another material to
become stable. In swimming pools, this process creates the formation of combined
chlorines, like chloramines, which do not sanitize and have adverse effects
on human skin. Use of ozone allows the chlorine to work primarily as a water
disinfectant.
• Pool water treatment can be broken down into three primary categories:
1. DISINFECTANT - The killing of living organisms (virus, bacteria, algae). This
consumes only 10-20% of the chlorine normally placed in a pool.
2. OxIDATION - The removal of non-living waste from pool water. This consumes up
to 70% of the chlorine placed in standard treated pools
3. RESIDUAL - The remaining, measurable sanitizer is left in the pool as a safety net
to maintain the water quality until it is brought through the pool equipment again.
Usually less than 10% of the chlorine originally placed in a pool is left over as
residual.
Installing a Clear O3® Water Purification system will reduce the amount of chlorine
needed to maintain a pool by up to70%.
THE BENEFITS OF USING OzONE INCLUDE:
• Fewer chemicals to maintain the pool.
• Less work to maintain the pool water.
• More enjoyable water, being treated similar to bottled water.
• Longer filter cycles, and increased life for the salt chlorinator cells (if present).
WHAT IS OzONE AND HOW DOES IT WORK

5
TO COMPLETE INSTALLATION YOU WILL NEED THE
FOLLOWING ITEMS (NOT INCLUDED)
SELECTING LOCATION & MOUNTING UNIT
(1) Six (6) feet ½" non-metallic conduit outdoor rated.
(1) ½" conduit compression fitting.
1. Select a location on a wall near the pool equipment or insert posts into the ground,
which will be used to hang unit. The Clear O3®unit should be at least one (1) foot
above maximum water level, and for extra safety the unit should be mounted higher
than the filter. The unit should be within five (5) feet of an electrical source, and
within nine (9) feet of plumbing connection. A solid surface is necessary to mount
unit. Mounting brackets are horizontally adjustable to line up with hard points on
the mounting surface. The unit must be mounted horizontally and level on the wall.
Electrical connections should be facing downward.
2. Use provided screws and plastic wall inserts or poles and pole mount clamps
(not included) depending on installation surface available.
3. Four (4) mounting brackets are included (two for the top slot and two for the
bottom slot.
4. Install anchors and screws in desired location for the top hangers. They must be no
further apart than twelve (12) inches. Do not tighten screws all the way. (Fig. 1)
5. Hang the Clear O3®from the two top brackets by sliding the keyhole slots over
the screws.
6. Mark the location for the two bottom brackets. (Fig. 2)
7. Remove the Clear O3® from the wall and install the wall anchors.
8. Place the Clear O3® unit back on the screws and line up the two lower brackets
with the wall anchors. (Fig. 3)
9. Install the bottom two screws and
tighten all screws.
Fig. 2 Fig. 3
12" Maximum
Fig. 1

6
Fig. 4 120 Vac 50-60 Hz 0.8A 230 Vac 50-60 Hz 0.38A
OUTPUT
30-60 Vac 700mA - 800mA CLASS P, TYPE
1, RATING: A “RS” ELECTRONIC BALLAST
BLACK
WHITE WHITE
WIRE NUTS
GREEN
BLACK
BLACK
WHITE
YELLOW WITH
GREEN STRIPE
2X BLUE 2X RED
LAMP
LT GREEN LT GREEN
WARNING:
Turn off power at main source before making any
electrical connections or servicing the unit.
1. A licensed electrician should make all electrical connections. Make sure the
unit is grounded by connecting to the pool equipments bond wire to comply
with local electrical codes.
2. Turn off power to the filtration system pump at the circuit breaker.
3. Install an approved seal tight flex conduit (not included) rated for outdoor
use, between the ClearO3 unit and filtration system pump time clock. Feed
the free ends of the wires from the ClearO3 through the conduit and into the
filter system pump time clock or equipment panel (Fig. 5A & 5B). Time clock
or equipment panel must be suitable for field wiring. Electrical connections
should be made in the time clock or equipment panel. NO ELECTRICAL
CONNECTIONS ARE TO BE MADE INSIDE THE CLEARO3!
3.1. The wires from the ClearO3 unit are provided to facilitate connecting to
a panel board that is a maximum of 10 feet away from the unit. If longer
conduit length is needed, then a Listed junction box suitable for the
application may need to be added. All electrical connections need to
be made in accordance with the National Electrical Code.
INTERNAL WIRING DIAGRAM OF THE CLEARO3
UNIT. NOT TO BE USED FOR INSTALLATION.
MAKING ELECTRICAL CONNECTIONS

7
4. Jumper Connections
4.1 Caution: Be sure of line voltage before
connecting the ClearO3 to the power
source. Connecting the ClearO3 to the
incorrect voltage can cause damage
to the unit. Connect green ground wire
to the time clock ground bar (Fig. 6A).
The Clear O3® unit is set to 240VAC
to be connected to the load side (Fig.
6B) of the filtration pump time clock.
4.2 The ballast may be switched to 120VAC
if the line voltage is 110VAC (Fig. 7A).
4.3 Move the jumper from the 220VAC
pins to the 110VAC pins (Fig. 7B).
4.4 If you do not have a terminal board and the
inside electrical connections look like (Fig.
8) contact Paramount for instructions on
how to change the voltage.
Fig. 5A
Fig. 5B
Ground Lug
Fig. 6A
Fig. 6A – Wiring connections
to be made inside time clock
or electrical panel.
Fig. 6B
Fig. 6B – Wiring connections
to be made inside time clock
or electrical panel.
Fig. 8
Fig. 7B
110 V
Fig. 7A
220V

8
The Clear O3® should run with the filter pump
as the filter pump creates the air draw through
the unit needed to create ozone. Do not set
the Clear O3® to run when the filter pump is
off and not pulling air through the unit.
5. Use external ground lug to connect the
Clear O3® to the pool pump ground bond.
(Fig. 5B)
6. Turn on power to filtration system pump.
Check glow tube on the left front of
the Clear O3®. A light blue light indicates lamp is lit and the unit should be
producing ozone. (Fig. 9)
WARNING:
UV light produced by this unit is harmful to the eyes and may cause
blindness! Do not look directly at a lit bulb!
Fig. 9
Light Blue Glow Tube
When a pool is built without a controller or time clock for the pump and a variable speed
pump is used the power input is hot all the time. The variable speed pump is turned on and
off by its own internal controller. There is nothing to connect the ClearO3 to (a relay in a
control panel) so it will turn on and off with the pump. When the ClearO3 is installed on these
pools it does not have a way to be turned off when the pump is not operating. These pumps
are available from all the major pool equipment suppliers and several small manufacturers.
Paramount has available an add-on paddle flow switch (Paramount part# 004-402-0010-00
or Grid Controls part # 57-F1-225-00W). The power is run through this switch and then to
the ClearO3. The flow switch is plumbed in the main line of the pool return. When it sees
flow the ClearO3 is turned on.
ALTERNATE ELECTRICAL CONNECTION FOR MULTI-SPEED
PUMP WITHOUT A CONTROLLER OF TIME CLOCK
Fig. 10 breaker panel
Clear03
steel tight flex
conduit
flow switch

9
1. Plumb the Flow Switch in the main
header after the filter. (Fig.10)
2. A licensed electrician should make all
electrical connections. Make sure the
unit is grounded by connecting to the
pool equipment bond wire to comply
with local electrical codes.
3. Turn off power to the filtration system
pump at the circuit breaker. (Fig 11)
4. Install an approved seal tight flex
conduit (not included) rated for
outdoor use between the breaker
panel and the flow switch and between
the ClearO3 and the breaker panel.
(Fig. 10)
5. Connect the black leg of the ClearO3
to normally open terminal of the flow
switch. (Fig. 12)
6. Connect a black wire to one of the
terminals of the filter pump breaker
and the other end to the power in
(common) terminal of the flow switch.
(Fig. 12)
7. Connect the red leg of the ClearO3
to the other terminal of the filter pump
breaker if a 220V circuit (Fig. 13)or to
the common bar in the electrical panel
for a 120V circuit. (Fig. 14)
8. Connect the green ground wire from
the ClearO3 to the ground bar in the
breaker panel. (Fig. 14)
Fig. 11
THE CLEARO3 UNIT IS FACTORY SET TO 240VAC. THE CLEARO3
SHOULD BE WIRED TO RUN WITH THE FILTER PUMP WHICH CREATES
THE AIR DRAW THROUGH THE UNIT NEEDED TO CREATE OzONE. DO
NOT SET THE CLEARO3 TO RUN WHEN THE FILTER PUMP IS OFF.
Fig. 12
common terminal
Normally open terminal.
Fig. 14
Fig. 13

10
9. Use the external ground lug to
connect the ClearO3 to the pool
pump bond wire. (Fig. 15)
10. Turn on power to the filtration
system pump. Check the glow
tube on the left front of the
ClearO3. (Fig. 16) A light blue light
indicates the lamp is lit and the unit
should be producing ozone.
NOTE: IF YOU SEE A RED OF
YELLOW LIGHT THRU THE GLOW
TUBE TURN OFF THE POWER
IMMEDIATELY AND REPLACE THE
LAMP. RUNNING THE UNIT WITH
A YELLOW OR RED LIGHT WILL
DAMAGE THE BALLAST.
WARNING:
UV light produced by this unit is harmful to the eyes and may cause
blindness! Do not look directly at a lit bulb!
Fig. 15
Ground Lug
Fig. 16
Light Blue Glow Tube
1. Turn off power to the filtration
system pump at the circuit breaker.
2. Pump strainer pot installation: (Fig. 17)
2.1 Check pump elevation above
water level. Refer to (Chart
1)for proper check valve
selection. The 0.5 lb valve
comes standard with Clear
O3® and others are available
to order separately.
2.2 Remove strainer pot plug. If
there is an O-Ring on plug
take O-Ring off of pot plug
and slide over threaded end of
check valve.
Fig. 17
MAKING PLUMBING CONNECTIONS
Chart 1
Pump Elevation
Above Water Level
Check Valve
Rating
Part Numbers
1' (30cm) 0.5 lb 005-402-1250-00
2' (60cm) 1.5 lb 005-402-2502-00
4' (120cm) 3.0 lb 005-401-2503-00
5' (150cm) 4.0 lb 005-401-2504-00

11
Fig. 18 2.3 Wrap the check valve four
times with teflon tape and
install into the strainer pot
plug-hole. Add more tape if
valve does not seal. (Fig. 18)
2.4 Install the combination needle
valve flow meter on the bottom
of the Clear O3® unit. (Fig. 19)
2.5 Install 3/8" OD x 1/4" ID
tubing to compression end of
check valve. (Fig. 20)
3. Pre-pump standpipe installation:
(Fig. 20 & 21A)
3.1 Cut cap off standpipe.
3.2 Glue a 3/4" elbow and a 3/4"
x 1/4" NPT reducer bushing on
end of standpipe.
3.3 Install the threaded end of the
check valve included in the
reducer bushing.
3.4 Install 3/8" OD x 1/4" ID
tubing to barbed end of check
valve. (Fig. 20)
Fig. 19
Fig. 21A NOT TO SCALE
WATER LINE
WATER LINE
2" PIPE
2" PIPE
3/4" PIPE 3/4" PIPE
3/4" PIPE
Fig. 20

12
4. OPTIONAL SUBMERGED
EQUIPMENT INSTALLATION
(FIG. 21B)
To complete this installation option you
will need a two way valve not included.
4.1 Install the two way valve on the
inlet pipe to the pump suction.
(before the standpipe if installed)
4.2 Make all other connections before
the two way valve.
4.3 Make tubing connections to the
pump pot or standpipe as in
standard pump above water level
installation.
4.4 Start the pump with the valve fully
open.
4.5 Note the filter pressure. Then
close the valve slightly until the
pressure on the filter drops two or
three psi.
4.6 Go to setting the airflow on page
19 to finish setting airflow. The
slight restriction this creates on
the pump is the same as if it was
set at approximately one foot
above water level and allows the
pump to draw air in at the pump
pot or standpipe.
(Fig. 21B)
5. Lay the 3/8 tubing along desired
route to the compression fitting on the
combination needle valve flow meter
on the Clear O3® unit.
6. Connect the tubing to the compression
fitting. (Fig. 22)
7. Use the provided wires ties to tie
the loose tubing to the conduit or
plumbing. (Fig. 23)
WATER LINE
TO SKIMMER
TO MDX
CLEAR O3
CLEAR O3
3-
WAY VALVE
2-WAY VALVE
*NOT TO SCALE*
2-WAY VALVE
3/4" PIPE
2" PIPE
WATER LINE
Fig. 21B
Fig. 22
Fig. 23

13
New Installation using Paramount venturi
installation kit.
TO COMPLETE THIS INSTALLATION YOU
WILL NEED THE FOLLOWING ITEMS (NOT
INCLUDED)
- (2) 2” X 2” X ¾” SLIP TEE
- (1) ¾” X ¾” UNION BALL VALVE
- (2) 2” VALVES ¾” FITTINGS AND PIPE
- (2) ¾” UNIONS
NOTE: ¾” PLUMBING CAN BE 2” IF
NEEDED FOR STRENGTH
1. Install two ea. 2" valves, and two each
2" X 2" by ¾" slip tees. One valve and one
slip tee on the suction side of the pump and
one slip tee and valve on the return side of
the pump (before the heater). (Fig. 24)
2. Plumb ¾" slip tee PVC from pressure side
tee into a union ball valve. (Fig. 25A)
3. Plumb ¾" PVC from the ball valve into the
inlet side of the venturi (coming from the
return line after the filter before the heater if
it has one.) (Fig. 25B)
4. Plumb ¾" PVC from the suction side tee
to a ball valve and union and then into the
outlet side of the venturi. Note: The venturi
must be level and removable for cleaning.
The flow arrow on the venturi must point
to show the flow to the suction side of the
pump. (Fig. 25B)
Fig. 24
Fig. 25A
Fig. 25B
OPTIONAL SUBMERGED EQUIPMENT INSTALL
2" x 2" x ¾" SLIP TEE
¾" UNION BALL VALVE
VENTURI
PRESSURE
SIDE FROM
FILTER
PRESSURE
SIDE FROM
FILTER
PRESSURE
SIDE FROM
FILTER
SUCTION SIDE
SUCTION SIDE
SUCTION SIDE

14
5. Connect a short piece of 3/8" OD X
¼" ID tubing on the barbed end of the
venturi.
6. Connect the ¼" barb in line check
valve to the short piece of tubing. Note:
The correct direction of flow through
the check valve (Fig. 26A & 26B).
7. Connect the rest of the 3/8" tubing
to the other end of the barbed in line
check valve.
8. Connect the tubing to the compression
fitting. (Fig. 27)
9. Connect the compression fitting to the
flow meter. (Fig 28)
VENTURI
3/4” PVC
FLOW
PRESSURE SIDE
FROM FILTER
SUCTION SIDE
TO POOL
Fig. 26A
CHECK VALVE
INSTALLED IN-LINE
3/8” OD X 1/4” IO TUBING
FLOW
PRESSURE SIDE
FROM FILTER
SUCTION SIDE
TO POOL
Fig. 26B
COMPRESSION FITTING
PRESSURE SIDE
FROM FILTER
SUCTION SIDE
TO POOL
Fig. 27
FLOW METER
PRESSURE SIDE
FROM FILTER
SUCTION SIDE
TO POOL
Fig. 28
NOTE: CLEAR O3 MUST BE
MOUNTED 1' ABOVE WATER
LEVEL
NOTE: CLEAR O3 MUST BE
MOUNTED 1' ABOVE WATER
LEVEL

15
The injector manifold must be installed in the pool’s main return line after the pool
filter, heater, chlorinator and spa return. (Fig. 29A) shows the basic installation.
Locate the appropriate section of the return line and install the injector manifold
using PVC primer and glue on all mating surfaces. Glue in a minimum 2” return line.
Water flow arrows on the manifold must be followed and the injector needs to be
facing up with the bypass down. See Fig. 29A & 29B.
The Clear03 ozone suction line will hook directly up to the bottom of the Clear03
and the other end to the injector with the check valve provided with the Clear03. No
flow meter is needed or provided.
NOTE: THE CLEARO3 UNIT MUST BE MOUNTED AT LEAST 1' ABOVE
POOL WATER LEVEL TO PREVENT WATER FROM CONTACTING
ELECTRICAL EQUIPMENT.
PUMP FILTER HEATER
VENTURI INJECTOR
CLEAR03
CHECK VALVE
RETURN WATER
SUCTION FROM
POOL OR SPA
PLUMBING FOR THE CLEAR03
USING THE VENTURI INJECTOR METHOD
Fig. 29A
Fig. 29B

16
1. Clean filter and pump basket before setting
airflow.
2. Turn the knob on the needle valve/flow meter
clockwise to close valve completely.
3. Turn the power on to the pump.
4. Turn the knob on the needle valve/flow meter
counter clockwise until the ball reads in the
middle of the two lines on the flow meter. (Fig. 30)
NOTE: From time to time condensation may collect in the flow meter, especially
in moist climates or following a rain storm. The moisture may cause the
orange ball to become stuck. The flow meter is not broken. The water will
eventually dry up and the ball will begin to float again. To check draw to
the pump look for air bubbles entering the pump pot.
IMPORTANT NOTES REGARDING THE FLOW METER:
1. IF THE PUMP THAT THE CLEAR 03® UNIT IS INSTALLED ON IS A PUMP
RUNNING A PARAMOUNT IN-FLOOR SYSTEM, lock the water valve on
pause (the pause control is located on top of the Paramount water valve) when
the valve is switching ports and therefore at it’s maximum flow. Set the flow
meter so the ball is on the upper line of the “normal” range.
2. WHEN USING MULTIPLE SPEED PUMPS, SET THE FLOW METER WITH
THE PUMP RUNNING ON THE HIGHEST SPEED THAT WILL BE USED.
3. The Clear O3 flow meter is very sensitive and the red ball may drop down
below the ‘normal’ marker after it has been set. If this happens on your unit,
please be aware that this is normal. The flow meter will still deliver the proper
amount of ozone as long as the blue light is on. You do not need to reset the
flow meter until after you clean your filter.
SETTING AIR FLOW
ExTERNAL SAFETY AIR BLEED KIT INSTRUCTIONS
(OPTIONAL)
Sometimes the internal air bleed on the
filter is not sufficient to handle the extra air
in the system with an ozonator installed.
An External Safety Air Bleed Kit (006-402-
3872-00) (Fig. 31) for in-ground swimming
pools is available to remove excess air from
the filter and send it downstream (up to 15’)
past all equipment. After installing always
Fig. 31
Fig. 30

17
test per instructions that air is vented from the filter when the pump is running. You
must install an external air bleed if the filter is old, does not have an internal air bleed,
there is a solar system on the pool or there is a robotic pressure side cleaner.
MOUNTING INSTRUCTIONS
1. Turn the power off to the pump.
2. Remove the pressure gauge from
the filter.
3. Install the nipple into one end of
the brass tee.
4. Install the pressure gauge by
threading into the other end of the
brass tee supplied.
5. Install the tubing compression
fitting by threading into the side of
the brass tee.
6. Install the tee assembly by
threading into the hole where you removed the pressure gauge (Fig. 32).
7. Insert one end of the tubing into the compression fitting (Fig. 32).
8. Turn the power on to the pump and check that air is coming from the other end of
the tubing.
9. Turn the power off to the pump.
10. Pick a spot on the return pipe downstream of all other devices (heater,
chlorinator, pressure cleaner, etc.)
11. Drill a 7/16” hole through the return pipe at the location selected.
12. Install the saddle clamp with the fitting over the hole. Make sure the gasket is in
place between the fitting and the pipe. (Fig. 32)
13. Lay the tubing along the return pipe to the saddle clamp fitting and cut off
excess length.
14. Connect the end of the tubing to the compression fitting on the saddle clamp
(Fig. 32). The tubing can be secured to the pipe using cable ties (not included).
Installation of External Safety Air Bleed Kit
Fig. 32
12 3
4
FROM
PUMP
FILTER
HEATER CHLORINATOR
BIOSTAT/
BIOCIDE
RETURN
LINE
NOTE:
Ozone production from direct UV light will decline over time. UV bulbs continue
to illuminate after they stop producing an effective level of ozone to clean your
pool water. To make sure your pool continues to receive all the benefits of ozone,
Paramount recommends that you replace your bulb every three (3) years.
WARNING:
• Turn off power at main source before making any electrical connections
or servicing the unit.
• UV light produced by this unit is harmful to the eyes and may cause
blindness! Do not look directly at a lit bulb!
BULB REPLACEMENT

18
1. Turn the power off to filtration system pump at circuit breaker.
2. Remove three screws in left end side cap labeled “electrical connections”. (Fig. 33)
3. Remove side cap. (Fig. 34)
4. Grasp light bulb plug and pull light out about one inch. (Fig. 35)
5. Remove plug from light bulb. (Fig. 36)
6. Pull light bulb free from Clear O3® unit. (Fig. 37)
7. Make sure gasket is in place on replacement light bulb.
8. Align with key and slide into hole until bulb seats firmly and completely into unit.
(Fig. 38)
9. Press plug onto light bulb.
10. Replace side cap and three screws.
11. Turn on power to filtration system pump.
12. Check glow tube on the left front of the Clear O3®. A light blue light indicates
lamp is lit and the unit should be producing ozone.
Fig. 34 Fig. 37
Fig. 35 Fig. 38
Fig. 33 Fig. 36

19
ISSUE SOLUTION
No air bubbles entering system or pool Clean filter then adjust airflow needle
valve
Filter empties and pump loses prime Replace check valve fitting at strainer pot
Light bulb does not light Check power to Clear O3®, then
replace bulb
TROUBLESHOOTING & SERVICE

20
4
5
612
11
2
1
3
8
10
9
7
14
13
(optional)
16
15
(optional)
17
19
(optional)
18
(optional)
20
(optional)