Parker GS Global Resources V12 Series Installation manual

Visit our homepage for additional support
parker.com/pmde
Bulletin HY30-8223-INST/EU
Installation and
start-up information
Hydraulic Motors
Series V12, V14 and T12
Effective: August 22, 2016
Supersedes: March 12, 2014
V12 V14
T12
T12
V12

Bulletin HY30-8223-INST
2Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic Motors
Series V12, V14 and T12
Installation and start-up information
Direction of rotation versus
flow
NOTE: The V12, V14 and T12 motors are
bi-directional.
V12 rotation:
- End cap position T (AC, AD and AH
controls): When port B (open arrow) is
pressurized, the motor rotates clockwise
(right hand; R), and when port A (black
arrow) is pressurized, the motor turns
counter clockwise (left hand; L)
- End cap position M (EO, EP, HO and
HP controls): A and B port positions inter-
change (A-to-B, B-to-A).
V14 rotation:
- Refer to the V14 illustration below right
(valid for all compensators and controls).
T12 rotation:
- Refer to the V14 illustration below right.
NOTE: Before installing a V12, V14 or
T12 motor in series (when both
A and B ports can be subject to
high pressures simultaneously)
contact Parker Hannifin.
V14_flow_rotation.eps
Leif A./
03-03-11
V12_flow_rotation.eps
Leif A./03-04-01
Direction of rotation vs. flow for the V12 mo-
tor (here shown with AC-compensator; end
cap position T).
Direction of rotation vs. flow for the V14
motor
(shown with AC-compensator).
Right hand
rotation (R)
Side port ARear port
A B
Left hand
rotation (L)
Side port B
Left
hand
rotation
(L)
Right
hand
rotation
(R)
Port A
Port B

HY30-8223-INST
3Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic Motors
Series V12, V14 and T12
Installation and start-up information
Filtration
Maximum motor sevice life is obtained when the fluid cleanlineness meets or exceeds ISO
code 20/18/13 (ISO 4406).
A 10 µm (absolute) filter is recommended.
Case pressure
To secure correct case pressure and lubrication, a spring loaded check valve, 1-3
bar, in the drain line (shown on next page) is recommended.
NOTE: Contact Parker Hannifin for information when operating at high speeds.
Min and max case pressure [bar] vs. shaft speed [rpm].
Frame size 1500 3000 4000 5000 6000
V12-60 max 12 0.5–7 1–5.5 1.5–5 2–5
V12-80 max 12 0.5–7 1–5.5 1.5–5 2.5–5
V14-110 max 10 1–6 1.5–5 2–4.5 3–5
V14-160 max 10 1–6 2–5.5 2.5–5.5 -
Required inlet pressure
The motor may operate as a pump under certain conditions. When this occurs, a minimum
pressure must be maintained at the inlet port; increased noise and gradually deteriorating
performance due to cavitation may otherwise be experienced.
A 15 bar inlet pressure, measured at the motor inlet port, satisfies most operating condi-
tions.
Contact Parker Hannifin for more specific information on inlet pressure requirements.
Operating temperatures
The following temperatures should not be exceeded
Main circuit: 80 °C.
Drain fluid: 115 °C.
Continuous operation at high power levels usually requires case flushing in order for the
fluid to stay above the minimum viscosity requirement. A flushing valve and restricting noz-
zle, available as an option, provide the necessary main circuit flushing flow.
Refer to fig. 1 (page 5), and to:

Bulletin HY30-8223-INST
4Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic Motors
Series V12, V14 and T12
Installation and start-up information
Drain ports
There are two drain ports on the V12 and T12 and three on the V14motors. The uppermost
drain port should always be utilized.
In order to avoid excessively high case pressure, the drain line should be connected di-
rectly to the reservoir.
V14 shown V14 shown
V14_drain.eps
Leif A./ 03-03-11
V14_drain.eps
Leif A./ 03-03-11
V14_drain.eps
Leif A./
03-03-11
Fig. 1.
Fig. 2. Fig. 3.
Flushing valve
(optional)
Drain and
cooling flow
to reservoir
Check valve
To reservoir
Check valve
Drain port
Alt. drain port
Alt. drain port
Alt. drain port
Drain port
Check
valve
Recom-
mended
1-3 bar
Alt. drain ports
To reservoir
V14 shown
Recom-
mended
1-3 bar
Recommended
1-3 bar

HY30-8223-INST
5Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic Motors
Series V12, V14 and T12
Installation and start-up information
Hydraulic fluids
Ratings and performance data for the motors are valid when a good quality, contamination-
free, petroleum-based fluid is used in the hydraulic system.
Hydraulic fluids type HLP (DIN 51524), automatic trans-mission fluids type A, or API CD
engine oils can be used.
When the hydraulic system has reached full operating temperature, the motor drain oil
viscosity should be above 8 mm2/s (cSt).
At start-up, the viscosity should not exceed 1500 mm2/s.
The ideal operating range for the motor is 15 to 30 mm2/s.
Fire resistant fluids, when used under modified opera-ting conditions, and synthetic fluids
are also suitable.
Contact Parker Hannifin for additional information about:
- Hydraulic fluid specifications
- Fire resistant fluids.
Before start-up
Make sure the motor case as well as the entire hydraulic system is filled with hy-
draulic fluid.
The internal leakage, especially at low operating pressures, is not sufficient to provide lubri-
cation at start-up.

Bulletin HY30-8223-INST
6Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic Motors
Series V12, V14 and T12
High Speed / High Power operation
Running in procedure at mid. displacement
Running In Example:
40
45
50
55
60
65
70
75
80
0 10 20 30 40 50 60 70 80 90 100
0
50
100
150
200
250
300
350
400
Temp [°C]
Pressure [bar]
Time [min]
Running In @ 500 rpm Drain Temp
Differential Pressure
Installation and start-up information
Running in procedure Parker Motors
We suggest the following procedure to run in the V12/V14/T12 motors.
1.Start @ 500 rpm, differential pressure 250 bar, outlet 10-15 bar.
2.Run until the drain temperature has passed its maximum* and has decreased 1-2 °C
3.Increase differential pressure to 350 bar
4.Run until the drain temperature has passed its maximum* and has decreased 1-2 °C
5.Increase differential pressure to 400 bar
6.Run until the drain temperature has passed its maximum* and has stabilized.
*If, at any point, the temperature tends to pass 100 °C, decrease the pressure at once.
Please make sure the drain temperature probe is in the drain oil flow to measure the
correct temp.

HY30-8223-INST
7Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic Motors
Series V12, V14 and T12
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED
HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY
DAMAGE.
This document and other information from Parker-Hannifin Corporation, its subsidiaries and
authorized distributors provide product or system options for further investigation by users having
technical expertise.
The user, through its own analysis and testing, is solely responsible for making the final selection
of the system and components and assuring that all performance, endurance, maintenance, safety
and warning requirements of the application are met. The user must analyze all aspects of the
application, follow applicable industry standards, and follow the information concerning the product
in the current product catalog and in any other materials provided from Parker or its subsidiaries or
authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or
system options based upon data or specifications provided by the user, the user is responsible for
determining that such data and specifications are suitable and sufficient for all applications and
reasonably foreseeable uses of the components or systems.
WARNING – USER RESPONSIBILITY
Installation and start-up information

Bulletin HY30-8223-INST
8Parker Hannifin
Pump & Motor Division Europe
Trollhättan, Sweden
Hydraulic Motors
Series V12, V14 and T12
Position notification regarding Machinery Directive 2006/42/EG:
Products made by the Pump & Motor Division Europe (PMDE) of Parker Hannifin are
excluded from the scope of the machinery directive following the “Cetop” Position Paper on
the implementation of the Machinery Directive 2006/ 42/ EC in the Fluid Power Industry.
All PMDE products are designed and manufactured considering the basic as well as the
proven safety principles according to:
• SSENISO13849-2:2008-09,C.2andC.3and,
• SSEN982+A1:2008,
so that the machines in which the products are incorporated meet the essential health and
safety requirements.
Confirmations for components to be proven component, e. g. for validation of hydraulic
systems, can only be provided after an analysis of the specific application, as the fact to be
a proven component mainly depends on the specific application.
Dr. Hans Haas
General Manager
Pump & Motor Division Europe
Parker Hannifin Manufacturing Sweden AB HY30-8223-INST/EU
Pump&MotorDivisionEurope Art.No3785940-06
461 82 Trollhättan
Sweden © Copyright 2016
Tel.+46(0)520404500 Allrightsreserved
www.parker.com/pmde
Declaration